Traditional Culture Encyclopedia - Hotel accommodation - What is the size of the flat glass door? How to install the flat glass door?

What is the size of the flat glass door? How to install the flat glass door?

Speaking of flat glass doors, I believe everyone is familiar with them. In the present decoration, flat glass doors can be seen everywhere, such as hotels, shopping malls, offices and so on. In addition to the role of partition, flat glass doors also play a beautiful and easy-to-observe effect. For example, flat glass doors in hotels and shopping malls can be seen at a glance, while in offices, flat glass doors play a transparent and observable role. Although flat glass doors can be seen everywhere, I believe many people still don't understand the relevant knowledge of flat glass doors. The following small series will explain the size and installation method of flat glass doors!

What is the size of the flat glass door?

The flat glass door has a frame or no frame, and its size will be determined flexibly according to the actual situation:

1. The frame part can be made more than 1500x3000mm if it meets the requirements, such as the floor spring door used for the gate of a shopping mall. Of course, the strength of the four frames should be sufficient.

2. It should not be greater than 1 100x2200mm in the case that the frameless is just a door clip.

3. Ordinary doors are 1000x2 100mm with or without frames.

How to install the flat glass door?

The installation of flat glass doors is more complicated than doors made of other materials, so the installation of flat glass doors should be cautious, which can effectively avoid causing some unnecessary injuries. Flat glass door is a special kind of door, and its thickness determines that it is not a solid door, nor does it conform to the characteristics of opposite sex doors. It is called a glass door mainly because its material contains glass. For example, when tempered transparent glass is used, the door leaf has a transparent function, and when frosted glass is used, the door leaf has a translucent function. Now let's take a look at the installation steps of the flat glass door. The installation of flat glass doors varies according to different types.

1.? Preparation before installation: Before installing the thick glass door, ensure that the ground construction and stainless steel or other decorative door frames have been completed. Thick glass limit groove has been set aside. Be very careful when chamfering the four corners-usually, you should hold a fine grinding wheel with your hands and grind the corners slowly to prevent the edges and corners from collapsing. The wooden base with stainless steel veneer should be fixed on the ground by wooden wedge nails. After that, the stainless steel veneer can be glued to the wood square. The aluminum alloy square pipe can be fixed on the frame column with aluminum angle or on the wooden wedge buried in the ground with wooden screws.

2.? Installation: firstly, use the glass sucker to suck the thick glass tightly, and then hold the sucker to lift the thick glass plate. It takes 2-3 people to lift it at the same time. After lifting, first insert the thick glass plate into the limit groove at the top of the door frame, then put it on the bottom bracket, and adjust the installation position so that the edge of the thick glass plate just seals the seam of the stainless steel decorative surface of the side frame column.

3.? Sealing by injecting glass glue: firstly, break the glass glue into the glass glue injection gun, and then support the bottom of the glass glue tank with the end plate of the back pressure bar of the glass glue gun. Hold the glass glue injection gun body with one hand and the glue injection handle with the other hand, and repeatedly operate the handle to loosen and squeeze out a small amount of glass glue for injection. Then aim the injection port of the glass glue at the gap end and seal it.

4.? Butt joint of thick glass plates: the thick glass plates of the fixed part are often not completed in one piece. When thick glass is butted, pay attention to the butt joint gap between 2 and 3 mm, and the edge of thick glass should be chamfered. After two pieces of connected thick glass are positioned and fixed, glass glue is injected into the gap. After filling, scrape the glass glue on both sides of the thick glass with a plastic cloth, and wipe off the glue marks with a clean cloth.

Seeing this, I believe everyone has an understanding of the size and installation scheme of flat glass doors. In fact, flat glass doors are very practical in daily decoration, both for individuals and enterprises. Because of the advantages of flat glass door, it has gradually replaced the traditional glass door, making home decoration more convenient and beautiful. The methods mentioned in this paper are only a small part of them. Those who have the idea of installing flat glass doors can refer to it, but they should also be analyzed in combination with field visits!

Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp; Wb, you can get it for free ~