What should I do if the toilet sewer leaks?

Question 1: What should I do if the toilet pipe leaks? Check the position of the water pipe first, and the leakage of the pipe body can be blocked with plugging agent. Just handle the joint of the pipe according to the tape falling off, aging or other reasons.

Question 2: What should I do if the toilet sewer leaks? Specific steps: 1. Tell upstairs not to use the toilet to drain water for 2 hours. Prepare epoxy resin or AB glue (two-component), 3. Prepare waste cotton cloth and cut it into 2CM strips. Clean the pipes that need to be repaired. 5. Start to fill the leak: wrap a layer of glue and a layer of cloth in the leaking place, and 6.OK.

Question 3: how to repair the leakage of cast iron sewer pipe in toilet with plastic steel soil? A and B components are mixed and smeared, and after curing, they are extremely hard. There is trachoma in the sewer part of my sink. In a few days, I will do this. I have bought something and solved the small problem.

Question 4: What should I do if there is water seepage around the bathroom pipeline? Generally, there will be a van on the street (specializing in building leakage).

They are all here to make a living, which is very good and can be guaranteed!

Question 5: What should I do if the toilet sewer leaks? This is because the waterproof layer of the bathroom is not done well. Find a bricklayer.

Question 6: It is clear who should repair the leaking sewer pipe in the bathroom. The owner of the pipe in the upper part of your bathroom is the resident upstairs, because 99% of the installation position of the drainage pipe is under the floor of your own house (that is, the roof of the downstairs resident). Give you a suggestion: first, you find a property and let the property negotiate. Second, you should find the upstairs residents to explain the reasons themselves. He stopped talking when he fixed it. He won't care if he doesn't fix it.

Question 7: How to prevent the toilet pipe from leaking? Please add, is it from the root of the pipeline or the ground?

1, coating waterproof materials can be simply divided into grade A and grade B; All solvent-based materials belong to Class A, including polyurethane two-component, one-component and SBS asphalt waterproof materials; All types of aqueous emulsions belong to Class B, JS and silicone. The solid content and performance of Class A are much better than that of Class B! !

2, let me talk about my construction experience, real years of construction experience, according to the transformation of old houses, new houses can omit some steps;

If the bathroom is waterproof, it will destroy the original waterproof layer;

1. After the ground is removed, level off all burrs and protruding parts;

2. 1:2 cement mortar (fine sand with silt content less than 1%), and 6% high ferric chloride waterproof solution are added to re-screed the leveling layer to make a water-collecting floor drain with gradient and slope direction (the responsible developer will set up a water-collecting floor drain in the center of the house for water-collecting and drainage of the filling layer, with the best effect; If not, we will take a bath on the slope and drain the floor; ) The mortar surface must be polished with an iron trowel, or even leveled with a scraper to reduce burrs! !

3, mortar screed-coat curing 7- 10 days to dry, must be dry, otherwise the waterproof layer will bulge damage!

4, the choice of waterproof coating, if it is my own work, I recommend solvent-based two-component polyurethane waterproof coating. I'm from Shandong, and I bought the paint from Shouguang Hongyuan Waterproof Company at a price of 12000/ ton. One set is two barrels of resin and one barrel of curing agent, about 75 kg, and the price is about1k. You can buy it at home, but you must have brown-red solvent-based polyurethane. Because the solid content and performance, durability, tensile strength, impact resistance, leveling and so on of Class A coatings are excellent, just because the price is too high for people to accept.

The dosage per square meter is 2.6-2.8kg, and it is brushed four times, with a total thickness of about 2.0mm!

Brush the bedding face for the first time, add resin and curing agent (that is, initiator, one thing) according to the ratio of 2: 1, weigh the mixture with a platform scale to ensure the accurate ratio, and then add diluent to dilute it. The diluent is pure xylene or pure gasoline, and xylene is better; After dilution, brush your head first, and then wait to dry. It usually takes 3-4 days to dry completely. Note that the pipe root is not brushed, the elevation is raised to 30 cm, and the height of the toilet faucet is 2.2 meters, so it can be brushed locally; The facade steps at the door must be brushed!

5. Next, treat the pipe root; Why brush the head first and then treat the root? Because this can prevent the dust pollution in the process of pipe root treatment and reduce the construction amount! Cut around the pipe root, with a depth of about 3-4 cm and a width of about 3 cm. Be sure to chisel, or it will leak! ! This may be the reason why you said that the pipeline is leaking-the root of the pipeline is leaking!

After chiseling, clean it with wire brush and vacuum cleaner, wipe the pipe with rag and dry it. The root of PVC riser is tightly wound with high-voltage electrical tape for 3-4 times, and the contact with concrete under the high-voltage tape is coated with glass glue (good); After drying, manual caulking with caulking agent is used to cultivate a small conical pile with a height of 20-30 mm;

Air drying and curing for 7-8 days;

All the dust on the working face is cleaned and dried;

6, besmear brushs waterproof coating for the second time, can be appropriate to add solvent (the first time is the thinnest, the role is to let the coating penetrate into the concrete, the thinner the better, the second time with less, the construction can be convenient);

Before the second construction, make up the pipe root that was leaked for the first time! !

7. After the second drying, spread a layer of 200-300g non-woven fabric as the reinforced matrix of the coating film; During construction, all bubbles are extruded and laid flat and dense;

8, besmear brushs paint for the third time and the fourth time;

9. After drying, build cofferdam around, waterproof to 10cm- 15cm, and press water for more than 72 hours. Go downstairs and see if there are any leaks. If there are, make up the brush. If not, it is qualified.

Be careful in the construction process! The waterproof finished in this way should be no problem for 20-30 years. The home made by myself is quite good, but the price is relatively high.

After waterproofing, apply a layer of 1- 1.5cm thick 1:3 cement fine sand mortar protective layer to prevent subsequent workers from damaging the construction! !

I struggled for a long time and it was very difficult. Hope to adopt, give points!

...& gt& gt

Question 8: How to deal with the water seepage at the joint between the toilet sewer and the ground? In many hotels, there are always annoying moldy edges in bathrooms, bathtubs, basins, seafood pool, shower rooms, footlines and countertops, which not only affect the appearance, lower the grade, but also affect the hygiene. This is because glass glue is used in these places, and glass glue itself is suitable for organic matter. Because the glass glue is wet by water, there will be many microorganisms such as mold growing between the surface and cracks of the glass glue. Over time, mold will cover the surface of glass glue and turn black. At the same time, mold will absorb more dirt and bacteria, making the edge of bathtub and corner look dirty and disgusting, which not only affects the appearance, but also feels unsanitary. Also often complained by guests. Maintenance personnel keep changing the glass glue edge, but they can't eradicate your troubles! Generally, glass glue will grow mildew in the second half of the year in a humid environment. A few imported mildew-proof adhesives can be used for one or two years, but they are expensive. Many five-star hotel executives have a headache. Their usual solution is to re-glue the glue once every six months, which is not only labor-consuming, time-consuming and expensive, but also troublesome. The poor viscosity of glass glue leads to its poor waterproof performance, and water will penetrate into the wall through the gap between the glue and the wall, making the wall wet, resulting in moldy and black latex paint or wallpaper in the room and falling off. All of the above are caused by moldy glass glue. If you are worried about these problems and feel helpless, then the sincere waterproof ceramic edge can help you solve this trouble. Ceramic edge is a new waterproof repair material and an upgraded product of glass glue, which can permanently solve the phenomenon of black and moldy bathtub edge and corner edge. The most prominent feature of ceramic edge is that it will never age and deteriorate, never grow mildew and turn black, and its waterproof performance is very strong. It can adhere tightly to the wall, making water impermeable. The ceramic edge contains chemical components that inhibit the growth of microorganisms, and its surface is as smooth as the ceramic surface (the color can also be made into the uniform color of the floor), so mold and bacteria cannot grow on its surface, and its surface is easy to clean, making the bathroom look bright and clean. Ceramic edge is also an environmentally friendly and non-toxic material.

Question 9: What is the reason for the water leakage around the toilet sewer?

Question 10: how to deal with the leakage at the joint of toilet sewer pipe? Remove the leaking pipe, or replace it, coat it with special PVC glue and connect it directly.

You can't stop the water leakage with raw material tape and black tape. If the water leakage is not serious,

It is also possible to apply glass glue to the outside of the pipeline and the leaking place, but only if the glass glue is applied,

The pipeline must be dry and kept for at least 12 hours.