Method for make firewood stove

First determine the construction location, open the flue and build the chimney.

1. Draw a line on the ground to determine the position of the firewood stove (the shape can also be round or square as required).

2. Draw a line on the wall to determine the height of the wood stove (the height of the wood stove is generally 78cm).

3, in the wall excavation flue hole (hole position application mortar seal)

4. build a chimney outside the house (it is higher than the roof, otherwise the smoke will choke the house)

Second, build a furnace body

Ordinary brick furnace body includes furnace door and ash outlet.

PS: Construction and measurement, including dimensions, elevation and other parameters.

Third, the furnace cavity

1, build the furnace chamber with refractory bricks.

2. The finished part, the space for quality inspection of furnace body and cavity, is filled with broken sand and gravel (solid can prevent smoke from escaping, increase strength and prolong life).

Four. Heat preservation and fire resistance construction of furnace and furnace surface

1, filled with thermal insulation material

2. Brick sand will be used to protect the furnace chamber and prepare for the construction of refractory slurry.

3, stove refractory mud construction (must be compacted)

4. Use a pot to compact the refractory mud above the furnace (the pot will be installed in this position later).

5, refractory mud screeding plastic

Five, flue, fire ring construction (technical jobs)

1. Take out the brick sand added to the furnace cavity in the previous step (at this time, the T-shirt can ensure that the refractory mud has a certain strength before construction).

2. Dig back the flue, flue and firestop ring in the circular pit where the pot is pressed out (is it like the outer wall of a tiger stove? Yes, this is technology)

Six, warm water mouth, pot mouth construction

1, these two small pots have been put away before the construction of thermal insulation materials and refractory mud, with the purpose of absorption and preheating, and adding water into them can turn them into warm water.

2. All the contact parts between the pot and the refractory mud are surrounded by steel bars to ensure the firmness of the pot mouth.

3. Smooth the kitchen surface with mortar to reach the expected height, generally 78cm.

Seven, ceramic tile decoration

1. Put tiles on all surfaces (pay attention to the position of the oven door, and the tiles at the ash outlet need to be cut).

2. Install the oven door flue baffle.

Eight. put into service

It can't be used immediately after it is built. You need to wait 15 days to ensure that the cement has solidified.

Immediate use will consume the water that should have been left for cement to set. In that case, if it takes 15 years, there will be a problem in one year.

Extended data

1. First, according to the size of the pot you want to build, draw the framework of the whole stove where you need to build it. According to the red brick, cut a circle on the border with a depth of 3 cm to prevent cracks from appearing below after burning. Then rinse with water and start laying bricks. Bricks are tiled, and a single brick is enough. Remember to leave a stove mouth in front, put a dust leakage net about 25 cm high at the bottom of the stove, and start taking the cigarette mouth behind the six-story brick.

2, build by laying bricks or stones, according to their own suitability to determine the height of the stove, smoke outlet according to the environment, the outlet should be in the downwind, outdoor construction should not be less than one meter of the stove.

3. Then build a pot. The pot is two centimeters higher than the stove, and the front stove mouth and the smoke outlet are the same size.

4, seven or eight centimeters on the ash leakage net, the overall modeling build by laying bricks or stones, square, cementing tile. After finishing, put it in the air for half a day and smoke the stove. In the meantime, sprinkle some cockroaches on the whole stove to prevent it from cracking. It takes about an hour to smoke, and it takes two days to sprinkle some ash irregularly.