How to install the top sprinkler; Precautions for Installation of Top Sprinkler [Detailed Description]

We must pay great attention to the installation of shower. If the installation is careless or not in place, it will affect the water outlet effect of the shower and the comfort of our bathing life, especially the top spray shower, which needs special attention when installing. Let me introduce you to the installation and precautions of the top spray shower.

1. Wrap the two elbows with raw material tape and screw them on the outlet connectors in the two mounting holes on the wall with adjustable wrench. After fastening, ensure that the center distance between the two elbow joints is150 mm.

2. Put two decorative sleeves on the elbow joint;

3. Insert the installation washer into the elbow joint, tighten the installation nuts on the two elbow joints with a wrench, and fix the faucet on the wall.

4. About what? h？ Positioning and drilling three holes with a diameter of 6mm and a depth of 35mm;

5. Drive the expansion pipes into the installation holes respectively, and fix the wall seat on the wall with self-tapping screws. Note: the wall seat must be on the same center line with the faucet outlet connector.

6. Wrap the faucet with cloth before drilling to avoid the faucet from being stained and bruised.

7. Height? h？ It needs to be determined according to the actual product during actual installation.

8. Insert the sealing ring into the lower end of the switch valve.

9. Tighten the lower end of the switch valve and the upper end of the faucet through threads.

10. Before drilling, wrap the faucet with cloth to prevent the faucet from being dirty and bruised. Note: When tightening with a wrench, be careful not to damage the electroplated surface.

1 1. Screw one end of the shower rod and one end of the switch valve together by thread (the end of the column shower rod must have a sealing ring).

12, then put the decorative cover into the other end of the shower bar, then insert that end into the wall seat, lock that end with three fastening screws respectively, and finally push the decorative cover onto the wall;

13. After installation, turn on the water inlet switch and thoroughly flush the pipeline.

14. Connect the nut end of the shower hose with the connector behind the switch valve body, and insert the nut into the shower seat after connecting with one end of the hand-held shower (Note: there must be washers at both ends of the shower hose.

15. Screw the top nozzle onto the shower panel.

1, height of mixing valve from the ground

The inner elbow is reserved for the shower head to prepare for the installation of the water mixing valve in the next step. Its height is generally between 90- 1 10cm, which can be determined according to the owner's requirements or the average height of husband and wife. It can't be higher than 1 10cm, otherwise it can't install a shower with a lifting rod, and it can't be lower than 90cm.

2. Spacing between two internal thread openings

Experienced plumbers all know that the reserved spacing standard of elbow in shower is concealed installation 15cm, with an error less than 5mm and exposed installation 10cm. Remember that everything is centered and measured. If it is too wide or too narrow, it is not appropriate. Don't rely on adjusting alignment. The adjustment range of alignment is very limited.

3. Keep the plane with the wall after pasting the wall brick.

The thread ends are reserved in consideration of the thickness of wall tiles, and it is better to make them 15mm higher than the blank wall. If it is flush with the blank wall, you will find that the thread is too deep in the wall after pasting the wall tiles, and maybe the shower will not fit. However, you dare not stay too high from the wall. If it is too high, the thread ends and adjusting screws will not be covered in the future decoration, which is very ugly.

4. Pay attention to different styles of showers.

Nowadays, with the continuous improvement of people's quality of life, shower styles are varied, and the installation methods are also different, such as surface installation, concealed installation, wall hanging and ceiling installation. As a hydropower worker, we should constantly learn and master the installation methods of new products in the market.

5. Site selection is very important.

Shower is a bathing equipment, and people don't wear clothes when taking a shower, so pay attention to its privacy when installing shower. Generally don't choose near the door or window. In addition, if there is an integral bathroom, it is necessary to fully communicate with the owner about the size of the integral bathroom to see where the shower mixing valve is left. Don't wait until the decoration is finished. After the bathroom is bought, we will smash the wall if the left position is not suitable.

6, left hot and right cold can't be wrong

There is nothing wrong with the left-hand heating and right-hand cooling of the elbow outlet of the shower. This is not only the national standard, but also the usage habit of the majority of owners. More importantly, the products of the manufacturers are also produced according to the regulations of left-hand heating and right-hand cooling. If you make a mistake, some equipment may not work or damage the equipment. This point should be paid attention to when laying pipelines.

7. Internal elbow fixation

It is very important to fix the inner conductor elbow. If it is not fixed, the size can not be positioned, and the mixed-flow valve may not be installed after the transformation.

I'm here to introduce the installation and matters needing attention of the top spray shower. After reading the above introduction, I believe you also know something about the installation of the top spray shower! If you need to install the top spray shower, you can refer to the above introduction for installation, so as to avoid unnecessary losses to your life due to improper installation.