How to use the shower switch

The shower switch can be used as follows:

1, two valves open at the same time.

When the electric water heater is in normal use, the two valves below must be opened, because how much hot water flows out of the water heater, how much cold water will be added, so that the water heater will not burn out. If cold water is not replenished, hot water will not flow out, so two valves must be opened at the same time.

Step 2 set the temperature

The electric water heater determines whether the water needs to be heated through the thermostat. Set a temperature, such as 50 degrees Celsius. When the water temperature is lower than this temperature, the thermostat will automatically turn on and the water heater will start heating. When the water temperature reaches the preset temperature of the water heater (most brands set it at 75-85 degrees Celsius), the thermostat will automatically turn off and the water heater will stop heating, and so on. At ordinary times, the bath water temperature at home can be set at 40 -50 degrees to prevent excessive burns, and the water temperature should be adjusted relatively higher in winter.

3, adjust the use temperature

When taking a bath, you can adjust the hot and cold water by rotating the faucet. When in use, turn the faucet to the middle position and let the water flow for a while. If the water temperature is too cold, turn to the red direction; if the water temperature is too hot, turn to the blue direction. (Generally, hot water is marked with H or red on the left side of the faucet, and cold water is marked with C or blue on the right side. )

4. Quick heating electric water heater

I just got home and I need hot water badly. When I turned on the power, it took a long time for the water heater to heat up. In order to solve this problem, you can choose a quick-heating electric water heater. At present, some fast-heating electric water heaters on the market only need to heat for 15 minutes, with fast heating speed and short waiting time. For example, A.O. Smith electric water heater, Jinguite special heating rod and patented dual-drive rapid heating technology can enjoy hot water without waiting too long.

5. How to use the shower

The use of the shower is very simple. We can turn on the switch to use it. There is hot and cold water in the shower. Usually, turn the switch to the right for cold water and to the left for hot water. Just adjust the water temperature to the right position. Some showers belong to constant temperature showers. There is a knob on the left and right sides of the faucet, and the knob on the left is used to adjust the water temperature. The knob on the right is used to control the water outlet mode and quantity. Everyone can adjust the water quantity and water temperature according to their own needs.

6, shower maintenance

Shower heads will get water stains if they are used for a long time. We can mix white vinegar with clear water in proportion, and then put the shower head in it for 2 hours. Finally, we can wash the shower head clean. We can also take the shower apart and wash the filter screen and water outlet with water.

7. Matters needing attention in using shower head

When using the shower head, try to avoid the shower head falling to the ground, especially the plastic shower head, so as to avoid the shower head being damaged due to bumping. When taking a bath, you can wipe the shower exit with a towel before the shower is over. If the shower head is made of stainless steel, it can be dredged with paper clips to ensure the shower head is unobstructed.

8. settle disputes

When using the shower, if the shower can't produce hot water, you can check whether the water inlet is blocked. If so, we will clean the filter gasket. It is also possible that the hot and cold water in the shower is connected backwards, and we just need to change it. If the water temperature of the shower is low, we can check whether the temperature of the water heater is set lower, if it is set higher.

9. How to use the shower

1. Turn the knob on the left to adjust the water temperature: Turn it forward and the water temperature will drop; Screw it back, the water temperature will rise, and it will not move when it is screwed to 40℃. This is because the water temperature over 40℃ is easy to burn the skin.

2. If you need hot water with higher water temperature, you must press and hold the red safety button on the knob to continue screwing it back.

3. The knob on the right controls the water outlet mode and water quantity: it is closed when the scale is aligned; Twist it forward and the bottom water outlet will come out. The more you twist it forward, the more water you have. Twist it back, and the flowers will splash. The more you twist it back, the bigger the water will be.