Summary model essay on quality inspection work

Summary of quality inspection work in 5 articles

As a quality inspector in Yilun Call Center, you must first know the name, job number and service quality of each employee. The following is a quality inspection summary essay that I compiled for you, hoping to help you!

On behalf of the hotel quality inspection department, I would like to summarize the work of this department in the past 20 years as follows:

1. sanitary inspection: the original detailed rules for sanitary inspection were revised and improved, the intensity of sanitary inspection was strengthened, and the number of sanitary inspections was increased.

2. Inspection of engineering problems: items requiring maintenance are found in the weekly routine inspection and reported to the engineering department in time.

3. Star special quality inspection: refer to the standards of four-star hotels, check and find items that do not meet the star standards, and feed back to all departments for rectification.

1, Front Office: As the facade of the hotel, the front office has always had high hygiene requirements. Because there is a lot of dust in the lobby, health problems are generally concentrated here. Compared with the past, the health condition has been greatly improved, but we still need to continue to work hard.

2. Housekeeping Department: The hygiene of guest rooms is our key inspection object, so the requirements are very strict, so the hygiene of each floor has been improved to varying degrees. For the sanitation of low floors, it is relatively difficult to work because there are relatively more dust, more guests, so it should be understood, but I still hope that the waiter will have high standards and strict requirements for room sanitation.

3. Security Department: The sanitation during quality inspection has been good, but the sanitation of the front and rear parking lots has been unsatisfactory. There is also the issue of fire safety inspection. During the quality inspection, I found that several inspections were not timely, and I don't know what would happen in the usual inspection. In short, safety is no small matter, so we must do a good job in fire safety inspection to prevent problems before they happen.

4. Engineering Department: There are many routine maintenance items pointed out by the quality inspection, which shows that the routine maintenance inspection of the engineering department is not in place, and I hope to pay attention to it in the future.

5.pa department: pa is responsible for many fields. Although there are often inadequacies, they can be corrected in time after being pointed out, and the sanitary condition of the customer service area is also good. The health of pa group should be classified and planned, and the health items that should be done every day, week and month should be made into tables to remind themselves to implement them.

6. Bathing Department: The hygiene of men's and women's bathing areas is still not in place at ordinary times, and there are many dead ends, but it can be corrected in time after being pointed out, probably because of the large bathing area and heavy workload, but I still hope that the waiters will have high standards and strict requirements for the hygiene of the bathing areas.

In a word, in the past year, with the cooperation of various departments, the sanitary condition of the hotel has reached a new level. In the next year, quality inspection will pay equal attention to health and service. I hope we can make progress together.

1. Quality inspection departments need to improve tabular and standardized management. The data analysis and summary carried out by the quality inspection department is relatively simple, the level is not deep enough, and the content collection is incomplete.

2. Insufficient allocation of quality inspection personnel leads to centralized inspection and lack of usual supervision. Professional quality inspection requires full-time quality inspection personnel, and establish and improve the system of regular inspection and spot check.

3. Inter-departmental communication and collaboration capabilities need to be strengthened. As a quality inspection department, while carrying out various tasks, we should strengthen communication and cooperation and create a good and harmonious working environment for the inspection atmosphere.

4. The follow-up inspection of quality inspection projects is not strong enough. Mainly rely on the department's self-examination, leading to the laziness of personnel in various departments.

Quality Inspection Summary (Part II) _ _ It's time to say goodbye. The memories of this year are busy and fruitful, which makes me happy and worried. I have done quality inspection in the injection molding workshop for more than 3 years, and I really have to work under pressure, but for me, no pressure means no motivation. As a quality inspector, in order to make myself grow faster and improve my work level, I made the following work summary this year:

First, check the quality of work.

As a quality inspector, you should not only master professional inspection knowledge, but also carefully find problems, find problems and solve them. So this year's on-site quality work has benefited me a lot. Learn to read product drawings and try to install products before inspection. According to the requirements of the quality process, do a good job of supervision, find and correct the problems existing in the inspection process. Cooperate with operators to conduct a comprehensive inspection of product quality, and promptly put forward and correct problems.

Follow up and check the whole process of special product processing technology to ensure that each process is qualified. Strictly control the quality of incoming materials and summarize the analysis results afterwards, so as to facilitate the continuous improvement of the work. Hand in the quality problems in the inspection process before going to work every day. Record the advantages of future problems that are easy to appear in the inspection process, and constantly improve the personal professional inspection level; Seriously reflect the quality problems existing in the site and the problems that the company needs to solve.

Second, the shortcomings and problems in the work

There is still a necessary gap in product quality requirements, which leads to the phenomenon of small batch return. On the one hand, due to the lack of detailed personal assessment and sufficient professional knowledge, on the other hand, the working hours are long, the workload is heavy and the work efficiency is not high. I'm not sure if I found any quality problems. I am not decisive, and some things need the help of the leader. At present, quality inspectors are understaffed, work long hours, and the workload increases, so one person can't take a vacation instead of one person.

Three. Work plan and improvement for next year

I will give full play to my advantages, improve my shortcomings and try my best to do my job well. We must adhere to a good mental state and carry forward the spirit of hard work, overcoming difficulties, striving for perfection, being rigorous and meticulous, learning and enterprising, and being brave in struggle. Clear up work ideas and improve work efficiency. Before inspection, we must first understand the products that need to be inspected, make preparations before inspection, and carefully supervise the inspection.

Our company is humanized management, focusing on cultivating employees' skills, team spirit and enthusiasm for work. I believe that I will grow together in the development of your big family, and we will grow and develop!

Summary of quality inspection (III) After our company won the bid for the safe drinking water project of Hongshawo Forest Farm, we immediately set up the project construction department to be responsible for the implementation and construction of the project. At the same time, the technical backbone with rich construction experience and strong business ability is selected as the technical director to enter the construction site. We will carry out the construction in strict accordance with the design scheme provided by the owner, adhere to the principle of "quality first", carefully construct, strictly manage, reasonably arrange construction machinery and equipment, make full use of effective working hours, improve mechanical efficiency, and ensure that the project is completed as scheduled according to the construction organization plan. The completion of the project is summarized as follows:

I. Overview of the Project

The project area is located in Hongshawo Forest Farm in Ganzhou City. The project is mainly used to solve the problem of safe drinking water for employees in Hongshawo Forest Farm. The main construction contents of this project include: a maintenance management room and a water purification room, each with an area of * * * 20m2, a water tower with brick-concrete structure (height 16m, volume 20m3), five inspection wells, and a water pump with the model of 100QJ2- 100/20.

Second, the project management

1. Engineering construction process

After winning the bid, the project department will prepare the construction organization plan in time and organize the construction team to enter the construction site in time according to the characteristics of the project.

In the process of project construction, the company appoints special personnel to be responsible for the construction and quality inspection of the project. At the same time, the leaders of Hongshawo Forest Farm visited the construction site from time to time for inspection and guidance, and put forward good opinions and suggestions, which effectively controlled the quality and progress of the project.

2. Project Budget and Financing The total investment of this project budget is 350,000 yuan.

3. Contract management

In order to ensure the quality and quantity of the project to be completed on schedule, this project signed a contract 1 copy with a contract amount of 350,000 yuan. During the execution of the contract, both parties consciously performed their respective rights and obligations, and no contract disputes occurred, and the contract was performed well.

4. Material supply

Materials such as cement, sand and gravel required for the construction of this project are purchased by our unit, and all kinds of products must have certificates of conformity and experimental reports before entering the construction site. Finally, it can be used under the supervision of engineers and technicians and quality inspectors. In engineering construction, all kinds of materials are supplied in time and with reliable quality, and strict material management ensures the progress and quality of engineering construction. The total quantity of safe drinking water project in Hongshawo Forest Farm is 8384m3, including a main maintenance management room and a water purification room with an area of * * * 20m2, a brick-concrete water tower (height 16m, volume 20m3), five inspection wells and a water pump100qj2-100. Consumption of cement 23, steel 2 tons. Complete 460 labor days.

5. Price settlement

The settlement of the project price shall be reported after the contractor, the owner and the site supervisor review the actual quantities, reviewed by the leaders of Hongshawo Forest Farm, signed by the project leader, and paid according to the completed project price. Up to now, the project has completed all contract quantities.

Third, the project quality

1. Project quality management

Before the implementation of the project, the project department made a detailed plan to complete the construction task of the project with a high starting point and high standards. During the construction process, according to the established engineering quality control standards, special personnel are assigned to carry out on-site monitoring, leaders of Hongshawo Forest Farm regularly or irregularly visit the site, and quality inspectors strictly control the quality to ensure that the engineering quality is not a problem.

2, the main project quality control

2. 1 quality control of well engineering

2. 1. 1 Select drilling equipment

According to the design depth of the well and the construction experience of our company, Red Star -300 water source drilling rig was selected for construction, and drilling officially started on September 2, 2000. In the process of equipment installation, strictly abide by the following operating procedures:

1. Install the drilling rig on a stable basis, straighten and stabilize local beams, and vertically lower the protective tube.

2. Install a lightning rod at the top of the drilling rig and stabilize the auxiliary leg.

3. According to the actual situation on site, transport loading and unloading sites, placement of drilling tools and drill pipes, mud pools, mud pumps, mud circulating tanks, etc. Are arranged not to influence each other.

4, electrical appliances placed in windproof, rainproof, moistureproof place, to ensure the safety of electricity.

5. After the drilling rig is in place, the rotary table and the protective tube should be aligned concentrically, the fuselage should be balanced, the rotary table should be horizontal, and the centers of the start, pulley and orifice should be kept "three points and one line".

2. 1.2 drilling method

This well adopts the construction scheme of coreless omni-directional drilling. Select 450mm jet tri-cone bit to open.

2. 1.3 Construction safety measures

1, comply with drilling safety operation regulations;

2. Complete and reliable safety protection facilities;

3, strictly implement the post operation procedures;

4, strict requirements of construction personnel consciously abide by the relevant rules and regulations of the owner.

2. 1.4 Problems needing attention in drilling

1. When drilling, the rotation speed is slow, the pressure is uniform, and the wellbore is vertical;

2. Strictly control WOB, and the pressure at the bottom of the hole shall not exceed 80% of the weight of the drill collar;

3, always pay attention to the pump pressure, pump volume, pump sound is normal;

4, careful operation, uniform drilling, pay attention to the drilling speed and bit operation, found that the torque increases, serious drilling jump, slow footage, etc. , measures should be taken to deal with it in time;

5. The wellbore is vertical, and there is no sudden change in azimuth and vertex angle;

6. The wellbore is round, without spiral and excessive size and shrinkage;

7. Pay attention to measuring mud performance and adjust mud performance index according to formation change.

2.2 Completion technology

2.2. 1 geophysical logging

After geophysical logging, according to logging curve and drilling layer judgment data, the exposed stratum is comprehensively analyzed and interpreted, and the water inflow section is determined to be 30-50m.

2.2.2 Through-hole, mud scraping and punching for slurry replacement.

After geophysical logging, run the drilling tool to the bottom of the hole, drill it after all the sediment returns, replace it with a brush, destroy the mud skin in the water inlet section, and then punch and change the mud until all the sediment returns from the hole and the mud performance meets the design requirements.

2.2.3 Run drill pipe for completion

1, fully prepared before running, with fine division of labor and clear responsibilities; Carefully check the quality of well pipes, such as sand holes, welding quality and other supporting equipment, such as reducing pipes, splints and centralizers. Accurately measure the length of well pipes, number them and put them in order. When running the pipe, it should be completed according to the technical specifications.

2), fill the filter material

According to the formation conditions, D 1-3mm natural timely gravel is used as the filter layer.

3), water stop

The water stop material is high-quality clay ball, which is divided into two sections to stop water.

4) Cementing

The cementing material is D 10-20mm gravel, the cementing position is 20-74.5m, and the dosage of gravel is about 10m3.

Summary of Quality Inspection Work (Chapter 4) In the busy work, we unconsciously ushered in a new year, and 20 years is meaningful, valuable and more rewarding. Looking back on this year's work, as an employee of the company, I deeply feel the hot air of the company's vigorous development. Over the past year, under the guidance of the leaders and through their unremitting efforts, they have cast themselves into a soldier who can fight hard, but there are also many shortcomings. Looking back on the past year, the work is summarized as follows:

First, performance.

Compared with the work performance in _ _, the achievement in _ _ is really a step up.

Company leaders predict that _ _ will be a bumper harvest year for our company. The first thing to do is to prepare a large number of inflatable cabinets to pave the way for future busyness. In just two or three months, more than 200 units were stocked. It also did not delay the normal shipment of the contract items.

Then, various schemes, large and small, poured into our inflatable cabinets. Guangdong Dongguan HWGO-4K * * * 70 sets, Hebei Zhangjiakou HWGO-2K4V-D * * * 22 sets, Guangdong Foshan Nanhai HWGO-4K * * 57 sets, Shanxi Electric Power HWGO-6K-D * * 15 sets, Shandong Weifang HW.

Second, shortcomings.

When two maintenance cabinets were doing experiments, it was found that the circuit resistance was unreasonable. When the cabinet was cut, the fixing bolts of the main circuit were not tightened. Through this incident, it shows that the workbench is too negligent.

With the continuous progress of the company, I get along with you day and night, so that I can constantly increase my work experience in enrichment. Sometimes, heavy work is too much for me. You must have a sense of responsibility if you want to work. It is my bounden duty to be a quality inspector. Every time I sprint like this, I am full of energy to filter every product. We should deeply reflect on our own mistakes in our work within one year to prevent them from happening again.

Work plan for 20__ years:

At work, we should be strict with ourselves and do all the work well according to relevant standards.

It can be predicted that the work in 20__ years will be more arduous and demanding, and the knowledge to be mastered will be broader and higher. So I will work hard, study hard and improve my cultural quality and various work skills.

Rationalization suggestions:

1. It is suggested that the overtime pay of quality inspectors is reasonable.

2. For the choice of leak detector, it is suggested to choose a quick and convenient instrument.

Summary of Quality Inspection Work (Chapter 5) The New Year is coming. On the occasion of bidding farewell to the old year and ushering in the new year, I would like to report to the leaders on my work in the past year and extend my most sincere New Year wishes to all of you, wishing you good health and all the best in the new year!

In the past year, with the support of the company and the project department, I worked as a full-time quality inspector in Chongqing Branch of China People's Bank and now Sunshine _ 0 Project Department.

In the past year's construction, with the care and help of many predecessors in the project department, my work has made great progress. In the company's monthly quality evaluation, I won six winning red flags. Of course, my achievements only represent the past, and I will redouble my efforts to do better in my future work. The following is a brief summary of the following points, please correct me:

Practicality of work

I learned from books that "scientific things can't be hypocritical and arrogant". In engineering, especially for special structural engineering or high-rise buildings, the technology content is high, which requires our quality inspectors to treat quality inspection work with a down-to-earth and rigorous attitude, be good at learning what they don't know, and constantly improve what they already know, because technology is constantly improved and updated, supplemented by refinement and practicality.

Vision at work

All engineering construction and quality inspection work runs through. In the accumulation of work experience, it can play a leading role in technology. For example, in the 9# building of Sunshine _ 0 Project Department, measures to prevent common faults are taken first, such as controlling the time of people and materials, pulling mortar to lift the floor in a certain period of time, mastering the time of formwork removal and doing well in maintenance, so that the building has almost no cracks so far. Of course, in the pouring process of the first few floors, due to the untimely delivery of concrete by the concrete company and the high temperature, some cold joints appeared. In the future work, I will constantly sum up the past experience and lessons, cultivate my foresight in my work and apply it to the project.

Cultivate the spirit of hard struggle

The construction industry is different from other industries. It needs constant on-site inspection and supervision to find and solve problems at any time, and these works are carried out in the harsh environment on the spot. This requires us to constantly cultivate the spirit of hard work, not afraid of hardship and fatigue, let go of the lofty attitude of managers, and constantly enrich our learned talents from the actual work of the project, so as to exercise and improve our on-site comprehensive processing ability.

Finally, strengthen the cultivation of their comprehensive quality.

As a member of ZTE, I am extremely proud to have the opportunity to study and exercise in such a large-scale market in Chongqing. This environment and external conditions give us a sense of self-confidence and glory, but it is more of a spur to our future work, requiring us to always restrain ourselves with ZTE's corporate image in our work. All our words and deeds must meet the standards of ZTE's super-first-class enterprises, and gradually cultivate our own personal qualities and self-cultivation, so as to be worthy of the trust and training of leaders.

The above is a simple summary of my project construction this year. Please criticize and correct me. In the new year, I will redouble my efforts and constantly improve my overall quality. Under the leadership of the company and the project department, I will continue to explore and innovate in the construction of Sunshine _ 0, and make Sunshine _ 0 a brand of ZTE. Finally, I firmly believe that with the vigorous development of ZTE and the careful training of company leaders, our technicians will grow up rapidly for the company's development.