What is the size and height of the socket in home decoration?

First, the height specification of home improvement socket

Switches are things that we touch every day in our lives. Only by properly installing the switch can we bring convenience and comfort to our life.

1, and the general switch distance is1.2 ~1.4m. According to the Code for Acceptance of Construction Quality of Building Electrical Engineering in China, the switch installation height is1.3m. This height refers to the height from the bottom edge of the switch. The switch height in the same room should be consistent.

2. The exposed socket is not less than 1.8m from the ground, and the concealed socket is preferably 0.3m from the ground.

Second, how many sockets are reserved for home decoration?

When we decorate our home, we need to budget the number of reserved sockets in the whole room. The number of reserved sockets for decoration varies according to the different functions of the room. Next, let's see how many sockets are reserved for home decoration.

1, kitchen

The functions of kitchen sockets are: lampblack machine socket, refrigerator socket, induction cooker socket, electric cooker socket, oven or microwave oven socket. Two sockets need to be reserved under the sink, one for kitchen treasures and one for water purifier, and another 1~2 socket needs to be reserved for electric kettle and other furniture.

2. Bathroom

The functions of the toilet socket are: the socket of the water heater (if an electric water heater is installed at home), the socket reserved for the smart toilet or the computer and the mirror in the toilet, which are mainly reserved for the use of hair dryers, razors or electric toothbrushes; Leave an exhaust fan and another spare socket. If the heating is not enough in winter, let this socket be prepared for the heater at home.

Note: the socket in the bathroom should be waterproof.

3. restaurants

Can be left to the water dispenser, or two hot pots using induction cookers can be reserved near the dining table; You can leave a blank wall. Turn on the fan without turning on the air conditioner.

4. Living room

Reserve one for TV; One wireless WIFI machine, one network receiver and one stereo (4 sets); There should be 1-2 on both sides of the sofa to facilitate our use of laptops; In addition, 1~2 socket is reserved to prepare for future expansion; Don't forget to leave one for the air conditioning socket.

5. Master bedroom

One on each side of the bed can be used to charge the mobile phone at home; 2~3 sockets are reserved on the desktop; Reserve a notebook computer; Electric fan, humidifier, air conditioner, etc. Should be retained; But also reserve one to expand.

6.the second bedroom

Leave one on each side of the bed; Keep a laptop; Leave an electric fan; Air conditioner, TV socket and humidifier socket are reserved 1 piece; Massage cushion should also leave a socket; In order to expand the production capacity, it is necessary to reserve 1 set.

Third, the height of the water heater socket

1, height of socket of electric water heater in toilet

Electric water heater socket 1800-2000mm, depending on the location of the electric water heater.

The installation level of the socket directly affects people's convenience and comfort, and also affects the visual beauty, so we must pay attention to it in the circuit transformation.

2, gas water heater socket height

(1) Water pipes are hot on the left and cold on the right, with parallel spacing 18cm and ground height1.4m..

(2) The height of socket is 1.8m, and the distance of bypass pipe is 20cm.

(3) If the gas pipeline needs to be embedded, the reserved position shall be lower than the water pipe by 10cm, so as to install the original water distribution pipe in the forest area.

(4) The flue opening is directly 63mm, and the height from the ground is 2.4m, which can be moved down or up synchronously 10cm.

(5) Pay special attention to the installation position of the water heater, and no water pipes and wires can pass through to avoid damage during installation.

The most basic condition for installing the water heater is that the room is higher than 2.4m, and the installation height of the water heater is 1.2 ~ 1.5m from the ground to the bottom of the water heater. The installation distance from other household appliances should also be moderate to avoid failures and unnecessary troubles. It is best to install in a well-ventilated place, and it is not allowed to be located in the bedroom, basement, living room, bathroom or closed room.

Installation regulations:

1, the concealed socket should not be less than 30cm from the ground.

2, ordinary socket, its installation height should not be less than1.3m;

3. The height difference of sockets installed in the same room should not be greater than 5 mm. The height difference of sockets installed in rows should not be greater than 2 mm.

4. The switch is generally installed at the same height as the arm, and it is 1.2~ 1.5m from the ground, depending on your needs.

Four-step method for selecting switch socket

I don't know where I saw the summary of switch socket selection made by which manufacturer. I think it's very good, very suitable for consumers, that is, watching, trying, smelling and weighing.

Look at the appearance

Look at the appearance. First, choose the appearance that suits your mind and can match the decoration at home. Then, whether there are defects, black spots, burrs and smoothness on the surface of the switch can be used to judge whether the material is of high quality.

Try to feel

Try to feel the touch. You usually need to press the button to try to feel the touch. If the switch is crisp, the sound is crisp and there is no sticking, it is very important to try to feel the touch. Some are hard, some are soft, some are long and some are short. Although each has its own needs, in general, the switch should be crisp, neither too hard nor too soft.

smell

Smell is smell. Many people know to buy a switch, turn it over and smell it. In fact, they just look at the material of the back seat. Nylon 66 has a strong plastic smell, which is generally used by large factories or low-end series without this material. ABS also has a slight smell, and PC material is colorless and tasteless.

Weighing assembly

It is natural to weigh the weight. In the switch socket, the most important material is the current-carrying parts, that is, copper sheets. The thicker the copper sheet, the heavier the weight, the better the toughness, the more times it is inserted and pulled, and it is still elastic and durable. Although it is not absolutely good, it is also a standard for consumers to judge intuitively.

The content is designed and provided by good user Mandy-yoko. For more questions, let's live in the APP and communicate directly with the host ~