Traditional Culture Encyclopedia - Hotel franchise - Chinese style bed making operation process
Chinese style bed making operation process
The operating procedures, methods and requirements for Chinese-style bed making 1. Tidying up the bed: During the process of removing linens, the mattress may shift and the pads may become warped. You must tidy up the bed in a clockwise direction. They reset, note: the front side of the protective pad should be facing up and free of stains and hair. 2. Spreading bed sheets: Spreading bed sheets is divided into three steps.
(1) To throw away the sheet: Use your left hand to grasp the label at the end of the sheet, and with your right hand to grasp the end of the sheet to loosen it, and throw it to the end of the bed, then grab the head of the sheet with your right hand and open the sheet on the left and right sides. .
(2) To place an order: With your hands about 80-100cm apart (determined by the center line of the sheet), with your palms facing down, grab the head of the sheet and press it about 30cm on the mattress, and then lift the sheet about 70cm height, so that the air enters the end of the bed and becomes bulging. Lean your body slightly forward and throw out the sheets with force. When the air pushes the end of the sheets away, adjust and pull the sheets toward the head of the bed until they droop 35cm.
(3) Corner wrapping: First wrap the bedside, tuck the drooping sheets at the headboard under the mattress, wrap the right corner, pull up and fold the drooping sheets on the right side with your left hand, and fold the right corner with your right hand Tuck the sheets under the mattress, then use your left hand to pull the folded corners down and wrap them at right angles. With your right hand, tuck the sheets with drooping corners under the mattress. Wrap the left corner in the same way as the right corner. Wrap the left and right corners of the end of the bed in the same way as the left and right corners of the head of the bed. Same. Note: After the entire sheet is laid, the front of the sheet should be on top, the sheet label should be at the end of the bed, and the midline should be in the middle. The sheet should be positioned at one time when billing is made, and the sheets should be tightly wrapped, and the four corners should be at right angles.
3. Entering the quilt cover: There are three steps to complete the quilt cover.
(1) Take the quilt cover and open it on the bed, then open the entrance of the quilt cover, face up and bottom down.
(2) Take the folded quilt to the end of the bed, distinguish the end of the quilt (the one with a trademark is the end of the quilt), fold the quilt head in three with your left hand, and hold the two corners of the quilt to top the quilt cover Stretch in the two corners, first align the left corner of the quilt with the corner of the left quilt cover, then align the corner of the right quilt and pull it down along the edge of the quilt and the edge of the quilt cover.
(3) Then you can straighten or throw it out according to your height, so that the quilt fits the quilt cover as much as possible. Place the inserted quilt in the middle on the bed. The inserted quilt should be flat. There should be no wrinkles, the length of both sides should be the same and naturally vertical, and should not bulge. The end of the quilt should be 20 centimeters away from the carpet, and the two corners of the end of the quilt should be raised as a standard.
(4) Pillow cover: Place the pillow core flat on the bed, open the mouth of the pillow bag with both hands to let in the air, put the pillow core into the pillow bag mouth, lift the upper edge of the pillow bag mouth with your left hand, and lift the upper edge of the pillow bag mouth with your right hand. Fold the pillow core in half and stuff it into the pillow bag. Then lift the mouth of the bag with both hands and stir it while lifting it. Finally, tuck the excess part of the pillow bag into the pillow core and close the bag mouth. Seal it.
(5) Place the pillow: Place the pillow flat and centered against the head of the bed. The placed pillow must be full and flat around the edges and the pillow core should not be exposed.
- Previous article:Which wedding banquet in Yunyan District of Guiyang is delicious?
- Next article:What does Taikoo Hui do?
- Related articles
- Why is the weather in Hunan hot and cold?
- How to get from Vienna Hotel Huizhou Yanda Avenue to Huizhou West Lake Park
- How to set off firecrackers with cranes at weddings?
- Beckham has contacted Messi to retire at Miami International. Will he join him?
- How to write a notice to a circle of friends after the Chinese New Year?
- Are you allowed to stay in a local hotel during the probation period?
- 10 Excellent composition harvested in summer vacation.
- Where is Fu's tomb?
- Living in an apartment for five nights in a row. Do you change your bedding every day? Have you changed the fee?
- What are eight places in Brunei that must be visited?