Is it safe to install radiators in the kitchen? How to install radiator?

For the radiator installed in home decoration, we must really master the installation process. This not only ensures our installation speed, but also ensures the installation quality of radiators. So if you plan to install radiators at home, you should understand the installation process of these radiators, including the following four points.

(A): radiator and pipeline positioning

①: If you plan to install the radiator, you must first confirm the installation position of the radiator. For example, in the bedroom, it is generally installed under the windowsill, in the living room, and can also be installed under the windowsill. So we have to go to every room and confirm the position of the radiator first.

②: Here we need to confirm the size of the radiator. For example, the radiator under the window sill can be installed at a height of 500. For the radiator on the wall, you can choose to install the radiator with the height of 1600 mm, and then accurately determine the installation position of the radiator according to the number of radiators. Then, according to the installation position of the radiator, the ink line in the direction of the heating water supply and return pipeline pops up on the wall.

(2): pipeline processing and pressure groove planing.

①: scratch the groove. Like the radiator installed in our home, the pipes are basically buried. The most common installation method is along the ground or along the wall. If slotting is allowed in our home, slotting is usually needed at this time. For example, a groove with a width of about 200mm and a depth of about 30mm is opened on the ground to meet the requirements of installing water supply pipes and return pipe. From the heating pipe to each radiator, operate along the elastic line.

②: After we confirm the specific installation position of the radiator and eject the line, we can process the pipe according to the confirmed position and ejection line. For example, the pipes used at home are basically PPR pipes, and we should also prepare corresponding elbow fittings. Then cut the pipe as needed. In this way, the pipes and fittings that need to be installed are ready.

(3): Install radiator and pipeline.

We can hang the radiator now. When the radiator is hung, it is hung on the wall according to the position we have determined. For example, the radiator installed under the window sill has two installation methods: one is floor installation and the other is wall installation. When installing the wall, the lower part of the radiator is about 25 cm from the ground. In this way, the radiator in each room is simply installed in place.

②: Connection of pipes. At this time, we need to install radiator tubes. When installing, it should be arranged from the location of the residents, and at the same time, it should be arranged for return pipe, return pipe. Here, the installation usually takes place in different ways. Fix the pipe in the groove or on the wall, and finally connect it with the radiator with pipe fittings. It is suggested to install a movable joint at the radiator joint for our maintenance.

(4): Pressing and flushing.

①: We should close the main valves of water supply pipes and return pipes that enter our room outdoors, and then suppress the radiators and pipes installed indoors. When pressing, tap water is poured into it, and then the pump is pressed manually. Generally, the pressure we hit is 0.6MPa, which is six kilograms, and then the pressure is stabilized. Stabilize the voltage for 30 minutes according to the specification requirements, and the pressure drop is not greater than 0.03MPa, which basically meets the requirements.

②: Rinse. Flushing is estimated that many friends have ignored this step, but this step must be done. After pumping, it should be taken out from the return pipe or tube well at the end of backwater, fitted with a flushing valve, and then flushed with tap water. If the pressure is not enough, it needs to be boosted. We need to clean all the impurities in the pipeline and the radiator system, and finally install the radiator.

How to install a radiator with good effect?

For the installation of radiator, it must be installed in the way of indoor water supply and backwater circulation. For example, for the next time, or for the next time, or for the next time, and then distinguish the same trip and different trips, so as to ensure the installation effect of the radiator. Specifically, we should ensure the following three points.

①: The installation method of supply and return water should be consistent with the main system to ensure the effect of radiator. For example, two pipes enter our room in parallel, which shows that the heating system in our home is different. Therefore, when installing, the backwater connected to the first radiator should be the starting end of backwater, which is what we call the different program. For other different forms of water supply and backwater, they should be installed according to their requirements.

②: Each radiator group has a separate control. The water supply pipes and return pipe of any group of radiators installed in our home must be controlled by valves before connecting the radiators, which is convenient for us to clean each group of radiators. Moreover, the parts where the radiator is connected with the pipeline should have flexible joints. In addition, each group of radiators should have automatic exhaust valves. This is the installation requirement of a complete radiator.

③: The radiator must be installed firmly. In other words, no matter whether our radiator is installed on the floor or on the wall, we should take corresponding measures to fix it firmly. For example, the most common floor installation, many friends may not install fixing clips, in fact, this method is not correct. Even if it is floor-mounted installation, it is necessary to install wall clips to ensure that the radiator is firm.