How to remove the broken light bulb of the dining room chandelier? What are the tips?

How to remove the broken light bulb of the dining room chandelier? What are the tips? Everyone should remove the broken light bulb from the chandelier first. This step is actually not very difficult. Open the lampshade of the chandelier first (if there is no lampshade, bypass it immediately), and you can immediately see the internal structure of the chandelier, just switching power supply and led light bar. Generally speaking, the led light is broken, which is in two cases. Either the waiting is broken or the switching power supply is broken. If you don't know what's going on, you can buy it according to the specifications of the switching power supply and the length of the lamp, both of which are not expensive. Generally, LEDs are divided into a few dollars, and it is not easy to break down all at once. Buy a few bright strips when a few dollars are broken. In addition, the colors in other areas are different, so you should distinguish them clearly when you buy them. If there are light bulbs on the chandelier, you should buy the right kind of light bulbs. Then carefully tear off the led light bar and be careful not to bend the led light bar.

Led strip was the first to be demolished and replaced. If it doesn't light up, it is likely that the switching power supply is broken. Replace the switching power supply. In short, no matter which one is broken, the other one can be saved, and the worst one can be replaced. After all the installation is completed and there is no problem in the test, you can put the lampshade back. After removing the lampshade, you can see a rectifier. The socket on the rectifier should be unplugged from the led tube, and then the spring plate that can't fix the led tube will break. At this point, the damaged led tube can be removed and replaced with a new one. However, attention should be paid to key points during operation, such as wearing disposable gloves to prevent electric shock accidents. Remember to repeat the above process after replacing the new bulb. After the bulb is glued to the collar, insert the power plug into the rectifier, and finally install the lampshade. But be sure to ensure safety when disassembling and replacing. No one expects all production safety accidents. We can try. If you turn on the power switch and then turn it on, it means that everyone has succeeded. There is another situation that must be noted, that is, if both ends of the led tube do not turn black after the lampshade is taken out, then it is possible that the rectifier is broken and another rectifier is replaced.

Grasp the structure of the chandelier and pull it out, then everyone will see the torsion spring inside the lamp, and then everyone must pull the torsion spring to the ceiling, so that the chandelier can be disassembled. If you can't get it out in the first step, you can try to remove the square buckle on the side of the chandelier. Don't worry about the situation in the middle and late stage of installation, because it can be installed on the splicing after installation. A strong sucker can be prepared in advance. The strong sucker can hold the hook of the glass sucker, hold a part of the edge of the aluminum alloy profile, and gradually drag it to the four corners of the ring, and then it can be removed from the chandelier. Before replacing the chandelier in the dining room kitchen, everyone should turn off the switching power supply, which is a very critical safety maintenance. We can't think that it is impossible to have a big problem if we change the chandelier. The problem usually happens under this idea. Later, after the power failure, everyone needs to check what the problem is, whether it is the damage of the light bulb or the poor contact of the power supply circuit of everyone's lamp.

After checking the circuit problem, everyone should look at the cause of the damage of the light bulb. If it is damaged, everyone must take off the lampshade and put on a new one. Or you can buy a special strong sucker in the sales market and use it to suck the fixed plate on the side. The corners must be done at once, so that they can be taken off immediately. This powerful sucker is quite cost-effective. Because the ceiling lamp specifications of the living room are all matched, you can't pry it open with a screwdriver. Because it is very easy to distort the original appearance, even if it cannot be installed, it is necessary to use professional special tools to replace the lamps as much as possible. If you can't solve it yourself, please ask a professional to replace it. It is best to set manholes along the pipeline laying route, which is beneficial to inspection. Be able to choose a location that is conducive to viewing in a secluded place, and carry out plastic arts solutions for manholes, such as setting integrated lighting or decorations. The restaurant kitchen should use raw materials such as metal materials and plastics. The restaurant kitchen must cook, cook, cook. Although the range hood and exhaust fan are installed, the kitchen fume cannot be completely discharged, and the decorative board or paint that is very easy to digest and absorb stains will deform and fall off.