Traditional Culture Encyclopedia - Hotel franchise - How to maintain the tiles?

How to maintain the tiles?

Key points of laying and maintenance of polished tiles

Polished tiles are common floor materials in home decoration. Its surface is smooth, bright and good in texture, especially in spacious halls, and the effect is better. How to lay and maintain polished tiles?

Inspection: Check the appearance quality such as color number, size and flatness at a position of about 3 meters.

Before paving: pave for 15 minutes, then pick it up until there is no water on the surface before construction. In order to obtain the most satisfactory paving effect, the pavement should be carried out in the same direction according to the product pattern characteristics or the trademark pattern on the back. When leveling, the direction can be adjusted by 180 degrees, and it is forbidden to adjust by 90 degrees.

Maintenance of polished tiles

1. Before laying and not using polished tiles, in order to avoid damaging the tile surface during other engineering construction, woven bags and other items that are not easy to decolorize should be used for protection, and the tile surface should be covered well.

2. If you need to use a nail air compressor on the paved brick surface, you should pad the air compressor with objects such as boards. It is forbidden for the wheels of the air compressor to directly contact the brick surface, so as to avoid the impact of the vibration of the air compressor on the brick surface.

3, daily cleaning mop floor, please try to use dry mop, less wet mop, local dirty or stained, can use household cleaners, such as detergent, washing powder, etc. Or use Dong Peng detergent to clean, and wax the floor regularly or irregularly according to the use situation, and then polish it until it is dry, so as to keep the brick surface as bright as new. If the economic conditions are good, please adopt crystal plane treatment to achieve the effect of a high-class hotel. Soak the brick in clear water: before laying, apply a layer of floor wax or antifouling agent to prevent dirt adsorption. After all works are completed, the anti-fouling agent should be removed from the brick surface. Pay attention to the color number and actual size of the variety on the outer packaging when paving.

Method for infiltration clean vitrified brick

Ceramics with water absorption less than 0.5% are called vitrified tiles, and polished tiles with water absorption less than 0.5% are also vitrified tiles (above 0.5%, only polished tiles are not vitrified tiles), and then vitrified tiles can be obtained by mirror polishing, because their hardness is relatively high and they are not easy to scratch. However, due to the rapid progress of ceramic technology, most tiles can achieve low water absorption, so vitrified tiles, vitrified polished tiles and polished tiles on the market are actually similar products. The lower the water absorption, the better the vitrification degree and the better the physical and chemical properties of the product.

In the process of using polished tiles, due to improper use, it may easily cause water seepage on the surface. Several common leakage treatment methods are as follows.

1, tea stains, fruit stains, coffee sauce vinegar, shoe prints and other stains are soaked in sodium hypochlorite diluent (bleach) for 20-30 minutes and then wiped with a cloth; Some stains that have penetrated into the brick for a long time will take several hours to soak.

2. Use sodium hypochlorite thinner (bleach) for the mildew spots formed by the mildew of ink and antifouling wax. When in use, just apply bleach to the stain and soak it for a few minutes to wipe it off.

3, cement, scale, water rust, rust spots with hydrochloric acid or phosphoric acid solution, rub a few times.

4. Use alkaline cleaner or organic solvent (acetone, triethylene) to clean paint, oil stain mark and surface antifouling wax layer, and remove paint and grease remover.

5. Usage of rubber hammer printing for decontamination: soak it in 20%-40% sodium hydroxide (NaOH) solution for 24 hours and then wipe it with cloth, then soak it in 30%-50% hydrochloric acid (Hcl) solution for 30 minutes and then wipe it with cloth.

6, ice cream alkaline cleaner

7, lime scale pickling agent

Remarks:

1, rubber gloves are required when using the above detergents;

2, after removing stains, scrub the brick surface with clear water;

3. The market or supermarket has the latest decontamination detergent. Please refer to the above decontamination scope and methods.