How to install the stair induction lamp? Detailed solution of step flow

The stair induction lamp recommended for everyone today, as its name implies, is a special lamp installed in stairs or aisles. If someone passes by, it will automatically sense and illuminate. On the one hand, when no one is around, they can automatically turn off, save energy and electricity, and are also green and environmentally friendly. On the other hand, they can choose the early purchase and adjust the brightness according to different needs. Today, I recommend the skills, procedures and precautions for the installation of stair induction lamp.

1. Installation method of stair induction lamp

1. First, find the power cord drawn from the projection floor from the corner (here called the main line, which is usually wired by the decoration unit), and the stair installer needs to extend the main line along the steps to the bottom step. We usually use RVB2*.75 or 2*.5 power cord.

2. First, put the cut treads on the steps, and then appropriately open several screw holes on the treads according to the length of the steps; (There is no clear requirement for the number of holes, and it depends on the actual situation on site. The more the number, the more secure it will be. Three screws need to be installed on the steps about 1M, and four screws need to be installed on the steps larger than 1.2M)

3. Put the expansion bolt into the screw hole, and then fix the treads firmly with self-tapping screws;

4. Install the cut light strip with the connected line into the light strip groove of the tread strip, and connect the end of the light strip to the main line; (Note that the thread end of the light strip should pass along the wire slot of the stopper, and it can't be pressed by other parts of the stopper, so as not to break the wire.) This needs to be advanced. First, install the light strip on the steps of the aluminum profile, and then put the aluminum profile on the steps.

5. Install the LED light board into the stopper, and connect the power cord of the number plate to the main line. If there is an LED light sign on one side of the steps, use a main line, which is placed on one side of the light sign; If there are LED signs on both sides of the steps, the left and right sides should adopt the main line or the power lines should be welded on both sides of the light strip, and the LED signs on the left (right) side should be connected to the main line on the other side through the light strip.

6. Place the left and right plug heads of the connected wires on both sides of the tread strip (pay attention to the routing of the main wire, which should be pressed in the slot of the plug head), put expansion bolts at the screw holes of the plug head, and then fix them firmly with self-tapping screws;

7. Re-install the high and low battens on the left and right sides in the horizontal direction and vertical direction, and pay attention to the main line to be hidden in the middle of the high and low battens; The gap between high and low battens and treads or the joint between high and low battens and high and low battens should not be too large.

8. When all the steps are equipped with stop heads and treads, uniformly install the stop head cover plate with number plate or the stop head cover plate without number plate;

2. Installation steps of the channel light bar:

1. First, install and fix the base of the channel light bar on the ground.

2. Connect the light strip and put it in the channel strip groove, and then cover the channel strip cover.

the step lights are all finished products, which are basically the same as the attached pictures. The drawings issued by the designer are only schematic diagrams and methods, which are subject to the finished step lights.

in addition, wooden boards with a width of about 1 cm should be installed on the front and vertical surfaces of each step before leveling, and the area where wooden boards are installed on the front of the step should be reserved in advance. After installing wooden boards, the surface of the wooden boards should be flush with the concrete plane, and then the step lights should be installed above them, which can reduce the fall-off caused by direct installation of the step lights on the surface of the cement floor for a long time.

from the above examples, we can know that whether the induction lamp of the later stairs can achieve satisfactory results as expected depends on many factors, including not only the choice of induction lamp brand of stairs, the decision of size, but also the attention and operation matters in the later installation methods and process steps. Today, we recommend an installation scheme suitable for induction lamp of stairs, from which we can know that, Prepare some appropriate corresponding spare parts products in advance, including expansion bolts and some profiles, and make wiring with reference to structural differences, so as to maximize the value of stair induction lamp.

Tuba Rabbit online provides free "decoration quotations, 1-4 local decoration companies, 3 sets of decoration design schemes", as well as decoration pit avoidance strategies! Click this link: /yezhu/zxbj-cszy.php? to8to_from=seo_zhidao_m_jiare& Wb, you can get it for free ~