Why are decorative fenders popular? What are the advantages? How to choose and maintain?

The small blackboard is ringing, and I begin to share the knowledge of fender wall ~

Advantages of wallboard-

1, warm in winter and cool in summer

Partition wood is a bad conductor, and a room with partition will be warm in winter and cool in summer.

Moreover, because wood itself can adjust the indoor air humidity, wallboard can be seen everywhere in castles and palaces with a history of hundreds of years in Europe, which is a necessary choice for high-grade decoration. Tested by the national authoritative department, the thermal insulation efficiency exceeds the existing national standards, and the temperature difference between the installation room and the ordinary plate installation room is 7 degrees; Compared with paint, the phase difference is 10 degree, achieving obvious energy-saving effect. 2. Health and environmental protection

Wood materials are natural and environmentally friendly, and they are tasteless when packed. If the room is decorated as a whole, there is no painting process, which solves the problem that the time of decoration materials and the smell of paint will not volatilize for a long time.

3. Air conditioning

Natural wood structure regulates the moisture in the air. When the pressure of water vapor in the air is greater than that of wood, wood absorbs water from the air, which is moisture absorption. On the contrary, desorption. Wood will adjust the moisture in the air through its own breathing. Give you physical fatigue.

4, high-grade, grade

Hundreds of years ago, partitions were first used in castles and palaces in Europe. Nowadays, partitions are widely used in high-end villas and five-star hotels. The partition endowed with the essence of classical culture and art is the first choice for high-end people to pursue high-end life taste and enjoyment.

5. Wear resistance and impact resistance

The separator has high compressive strength and flexural strength, and is an upgraded product of latex paint. Wear resistance and damage resistance are far better than ordinary paint and wallpaper, and it is more suitable if there are children at home. The TV background, sofa background, dining room background and bedside background at home can protect the wall well, and decorative paintings and warm photos can be hung or pasted.

6, UV protection, radiation protection

The partition has a strong absorption effect on ultraviolet rays and radiation, and wood can scatter light, reducing eye fatigue and injury.

7. Reduce noise and improve sleep quality.

The sound insulation of the partition is 29 decibels, which is equivalent to that of most solid walls. For example, the underwater sound of sewer pipes in bedrooms and bathrooms can absorb sound well.

The wallboard produces perfect diffuse reflection of sound, effectively buffering the impact of heavy bass, and the material itself absorbs the bad sharp waves of sound, thus forming a perfect three-level noise reduction function in space, greatly improving the sleep quality of one third of life. Partition type-

The base materials of high-grade wallboard are all wood. The surfaces are all treated,

There are imitation solid wood, imitation stone, imitation ceramic tile, imitation wallpaper and other patterns. Among them, solid wood products are widely used in home decoration. Solid wood products include imitation bar wood, Fraxinus mandshurica, teak, oak, walnut, rosewood, cherry and other patterns, which can be purchased according to the needs of home improvement! Selection skills of protective wall-

1. Selection of wallboard quality: quality can be identified from both inside and outside. The internal quality mainly tests the hardness of its surface and the firmness of the adhesion between the substrate and the surface smoothness. Good quality products have high hardness, impact resistance, wear resistance, no obvious knife marks on the surface and no separation between the surface and the substrate. Appearance quality mainly depends on the degree of simulation. Good quality products have vivid patterns, uniform processing specifications, free splicing and good decorative effect. The strip partition shall be sealed with plastic and shall not be deformed.

2. Material selection of wallboard: according to the type of substrate, it can be divided into two categories: wood and plastic, in which wood can be divided into strip profiles and whole boards; From the processing technology of the substrate, it can be divided into solid wood composite board, medium density board and plywood. No matter what material the substrate is made of, the surface has been treated and has a variety of patterns, such as pure solid wood, imitation solid wood, imitation stone, imitation ceramic tile, imitation wallpaper, wooden stick, manchurian ash, teak, oak and other natural textures. Solid wood composite wallboard is widely used in home decoration.

Precautions for purchasing protective walls-

1. When selecting wallboard, the board with high surface hardness should be selected, which has good impact resistance and wear resistance and is not easy to fall off between the surface and the substrate;

2. Carefully observe the surface pattern by picking the partition, and choose the surface pattern that is realistic, freely spliced and highly simulated.

3. The partition is divided into solid wood composite board, medium density board and plywood, and the middle of the partition is also divided into whole board and lath;

4. The surface of the skirting line is generally treated once, so the surface of the skirting line will have the natural texture of wood, and various patterns such as elm, manchurian ash, imitation tiles, wallpaper, etc.

Thickness of dado-

1, the height of the clapboard is generally 900 ~ 1200mm, and the height of the whole clapboard is generally 2 100 ~ 2300mm. Before installing the partition, the wall surface should be leveled to remove floating ash, and the uneven wall surface should be leveled with putty. Wet walls should be coated with waterproof paint. The panel can be fixed with nail-free glue, which is convenient to install, fast and without nail holes. The angle of yin and yang of wallboard must be vertical and horizontal; Kick angle boards and battens are close to the panel, and there can be no gaps. Docking must be at a 45-degree angle; Visually, the panel height of the clapboard should be consistent; The joint width between panels should be uniform; The diagonal deviation of veneer shall not be greater than 2 mm, and the surface shall be smooth and the wood grain shall be clear.

2. Wood wallboard. Bury the anticorrosive wooden brick in the wall, fix the wooden keel frame on the wooden brick, and then nail or stick the panel on the wooden keel frame. The cross section of wooden keel is 20 ~ 40mm× 40 ~ 50mm, and the spacing of wooden keel is 400 ~ 600mm.

3, metope requirements level off. If the leveling error of the wall is within 10 mm, plastering and trimming can be used; If the error is greater than 10 mm, a pad can be added between the wall and the keel.

4. According to the height of the partition and the size of the room, nail wooden sticks through the bone and install them in whole or in blocks. Install skirting board at the bottom of the wooden dado, and fix the skirting board on the skid and wallboard. The height of the skirting board is 150 mm, and fix it on the partition with wooden lines.

Panel installation-

1. Measure the length and width of the wall surface, and calculate the integral block of the required wallboard according to the size of the wallboard. The extra space should be completed by splicing the wall panels, and the splicing should be distributed at the ends.

2. Fix the skirting hook on the wall with expansion screws or steel nails. Hook holes are 7.8cm away from the ground, a hook is fixed every 60cm, and then the skirting line with one end processed into a 45 angle is hung on the hook. In areas with high humidity, the combination of two skirting lines must leave appropriate expansion joints, especially in the corner where furniture is placed, and more expansion joints should be considered.

3. Insert the partition board into the skirting line from left to right, and the starting block should be slotted from corner to corner. Install expansion screws or steel nails at a distance of 1.5cm from the top of the panel (in the middle of the width of the panel). Pay attention to the fact that the screws can't expose the surface of the panel. When the power switch is still encountered in the construction, a hole slightly smaller than the switch can be chiseled with a chisel, and the external angle can be used when the column is encountered. Apply special glue to the groove of the waistline, and insert the concave-convex surface after a few minutes. The corner must be 45 diagonal.

4. First saw off the convex groove of the first partition and planed it with a chisel. Then from the corner, install a 4.9cm( 1.5in) steel nail on the protruding part of the groove every 60cm, and the joint of the groove wedge does not need to be glued. Each piece should be hammered tightly and corrected with a ruler. The last piece needs to be coated with special glue on the back of the wallboard.

5. The top corner line can be coated with special glue on both sides, stuck on the top corner, pulled apart for a few minutes, and then glued tightly.

Maintenance of protective wall-

Product maintenance is mainly based on wood essential oil.

Now you understand why it is popular to decorate fender walls! Do you like the renderings of the bulwark? Don't forget to put the relevant decoration tips in your collection pocket. If you want to know more, please continue to follow us.

The internal quality mainly tests the hardness of its surface and the firmness of the adhesion between the substrate and the surface smoothness. Good quality products have high hardness, impact resistance, wear resistance, no obvious knife marks on the surface and no separation between the surface and the substrate. Appearance quality mainly depends on the degree of simulation. Good quality products have vivid patterns, uniform processing specifications, free splicing and good decorative effect. The strip partition shall be sealed with plastic and shall not be deformed. 2. Material selection of wallboard: according to the type of substrate, it can be divided into two categories: wood and plastic, in which wood can be divided into strip profiles and whole boards; From the processing technology of the substrate, it can be divided into solid wood composite board, medium density board and plywood. No matter what material the substrate is made of, the surface has been treated and has a variety of patterns, such as pure solid wood, imitation solid wood, imitation stone, imitation ceramic tile, imitation wallpaper, wooden stick, manchurian ash, teak, oak and other natural textures. Solid wood composite wallboard is widely used in home decoration.

Precautions for purchasing protective walls-

1. When selecting wallboard, the board with high surface hardness should be selected, which has good impact resistance and wear resistance and is not easy to fall off between the surface and the substrate;

2. Carefully observe the surface pattern by picking the partition, and choose the surface pattern that is realistic, freely spliced and highly simulated.

3. The partition is divided into solid wood composite board, medium density board and plywood, and the middle of the partition is also divided into whole board and lath;

4. The surface of the skirting line is generally treated once, so the surface of the skirting line will have the natural texture of wood, and various patterns such as elm, ash, imitation tile, wallpaper, etc.

Thickness of dado-

1, the height of the clapboard is generally 900 ~ 1200mm, and the height of the whole clapboard is generally 2 100 ~ 2300mm. Before installing the partition, the wall surface should be leveled to remove floating ash, and the uneven wall surface should be leveled with putty. Wet walls should be coated with waterproof paint. The panel can be fixed with nail-free glue, which is convenient to install, fast and without nail holes. The angle of yin and yang of wallboard must be vertical and horizontal; Kick angle boards and battens are close to the panel, and there can be no gaps. Docking must be at a 45-degree angle; Visually, the panel height of the clapboard should be consistent; The joint width between panels should be uniform; The diagonal deviation of veneer shall not be greater than 2 mm, and the surface shall be smooth and the wood grain shall be clear.

2. Wood wallboard. Bury the anticorrosive wooden brick in the wall, fix the wooden keel frame on the wooden brick, and then nail or stick the panel on the wooden keel frame. The cross section of wooden keel is 20 ~ 40mm× 40 ~ 50mm, and the spacing of wooden keel is 400 ~ 600mm.

3, metope requirements level off. If the leveling error of the wall is within 10 mm, plastering and trimming can be used; If the error is greater than 10 mm, a pad can be added between the wall and the keel.

4. According to the height of the partition and the size of the room, nail wooden sticks through the bone and install them in whole or in blocks. Install skirting boards at the bottom of the wooden dado, and fix the skirting boards on the skids and wallboard. The height of the skirting boards is 150 mm, and fix them on the partition with wooden lines.

Panel installation-

1. Measure the length and width of the wall surface, and calculate the integral block of the required wallboard according to the size of the wallboard. The extra space should be completed by splicing the wall panels, and the splicing should be distributed at the ends.

2. Fix the skirting hook on the wall with expansion screws or steel nails. Hook holes are 7.8cm away from the ground, a hook is fixed every 60cm, and then the skirting line with one end processed into a 45 angle is hung on the hook. In areas with high humidity, the combination of two skirting lines must leave appropriate expansion joints, especially in the corner where furniture is placed, and more expansion joints should be considered.

3. Insert the partition board into the skirting line from left to right, and the starting block should be slotted from corner to corner. Install expansion screws or steel nails at a distance of 1.5cm from the top of the panel (in the middle of the width of the panel). Pay attention to the fact that the screws can't expose the surface of the panel. When the power switch is still encountered in the construction, a hole slightly smaller than the switch can be chiseled with a chisel, and the external angle can be used when the column is encountered. Apply special glue to the groove of the waistline, and insert the concave-convex surface after a few minutes. The corner must be 45 diagonal.

4. First saw off the convex groove of the first partition and planed it with a chisel. Then from the corner, install a 4.9cm( 1.5in) steel nail on the protruding part of the groove every 60cm, and the joint of the groove wedge does not need to be glued. Each piece should be hammered tightly and corrected with a ruler. The last piece needs to be coated with special glue on the back of the wallboard.

5. The top corner line can be coated with special glue on both sides, stuck on the top corner, pulled apart for a few minutes, and then glued tightly.

Maintenance of protective wall-

Product maintenance is mainly based on wood essential oil.

Now you understand why it is popular to decorate fender walls! Do you like the renderings of the bulwark? Don't forget to put the relevant decoration tips in your collection pocket. If you want to know more, please continue to follow us.