What are the acceptance criteria for hotels (guesthouses)?

There are too many words in the acceptance standards such as what you said, so I will not go into details one by one. I will provide you with some basic interior completion acceptance content below for your reference. I hope it will be helpful to you:

p>

Acceptance standards for coating projects in civil construction:

Applicable to various indoor and outdoor emulsion coatings, solvent-based coatings (including oil-based coatings), varnishes and art coatings and other coating projects.

Guarantee items: The product name, grade, type, color, performance, etc. used for engineering coating and semi-finished products must meet the requirements of the design or selected samples. (Instructions for use should be attached) The engineering coating base must comply with the relevant provisions of this standard. The pattern, color, and type and grade of materials used for artistic coating must comply with the requirements of the design sample, and the quality of the underlying coating should comply with the relevant regulations of the corresponding grade. The thickness of the sprayed coating should be uniform and consistent in color, and the spray points and protruding points of the spray flowers should have a comfortable feel and no grains falling off. The sprayed stubble should be left at the grid joints without obvious color difference. When there are no grid joints, the joints should not have overlap marks. The sprayed surface should be clean and pollution-free.

Inspection methods: observation, hand inspection, and inspection of product certificates.

Basic items

The quality of the surface where thin materials are applied should comply with the requirements in Table 1.

Thin coating engineering quality inspection items table 1

Items

Items

Quality standards

Inspection methods

1

Powder loss and peeling

Not allowed

Observation and hand inspection

2< /p>

Alkali return and color bite

Not allowed

Observation and inspection

3

Leakage and see-through

p>

Qualified

No obvious penetration

Observation and inspection

Excellent

Not allowed

4

Shedding and bumps

Qualified

No shedding or bumps in obvious places

Observation and hand inspection

< p>Excellent

None

5

Color and brush pattern

Qualified

Consistent color, trachoma, The brush marks are not obvious

Observation and inspection

Excellent

The color is consistent, no trachoma or brush marks

6

The color separation line of the decorative line is straight

Qualified

The deviation is not more than 2mm

Pull the 5m line (less than 5m to pull through the line) and check with a ruler

p>

Excellent

The deviation is not greater than 1mm

7

Doors, windows, glass lamps, etc.

Qualified

< p>Doors and windows are clean, glass and lamps are basically clean

Observation and inspection

Excellent

All clean

Quality of the surface of thick paint construction projects Should comply with the requirements of Table 2.

Item

Item

Quality Standard

Inspection Method

1

Alkali return, color peeling and peeling

Qualified

Obvious, the rest is not obvious

Observation and inspection

Excellent

None

2

Less coating, see-through

Qualified

No obvious areas

Observation and inspection

Excellent

None

3

Color, dot distribution

Qualified

The color is consistent, the spray point at 1.5m is evenly brushed and the texture is smooth

Observation and inspection

Excellent

The color is consistent, the spray point at 1m is even and smooth

4

Doors, windows, glass lamps, etc.

Qualified

Doors and windows are clean, glass, lamps, etc. are basically clean

Observation and inspection

Excellent

Completely clean

The quality of the surface where the composite coating is applied should comply with the requirements in Table 3.

Table 3 of quality inspection items for composite coating projects

Items

Items

Synthetic resin emulsion composite coatings

Silicon solution type multi-layer coating

Reaction-curing multi-layer coating

Inspection method

1

Powder loss and flaking Skin

Not allowed

Observation and touch inspection

2

Alkali return and color bite

Passed

There is no bite color in obvious areas, and no other defects

Observation and inspection

Excellent

None

3

p>

Leakage and see-through

Qualified

No obvious defects

Observation and inspection

Excellent

None

4

Spraying points, density and degree

Qualified

The density is even and the spraying points are uniform at 1.5m when viewed from the front Continuous film is not allowed

Observation and inspection

Excellent

The density is uniform, and the spray points at 1m are uniform and diagonal. Continuous film is not allowed

< p>5

Color

Qualified

The obvious parts are consistent in color, and the inconspicuous parts are basically the same

Observation and inspection

< p>Excellent

Consistent color

6

Doors, windows, glass lamps, etc.

Qualified

Doors and windows are clean, Basic

observation and inspection

Excellent

Clean

The surface quality of glass lamps and other projects coated with solvent mixed color materials should comply with the requirements in Table 4.

Table 4 of project quality inspection items for solvent-based mixed color coatings

Items

Items

Quality Standards

Inspection method

1

Peeling, missing brush and rust return

Not allowed

Observation and inspection

2< /p>

Color separation and edge wrapping

Qualified

None on the large surface, 1mm deviation allowed on the small surface

Observation and inspection

Excellent

No large or small surface

3

See-through bottom, sagging or wrinkled skin

Qualified

None on the large surface, obvious absence on the small surface

Observation and inspection

Excellent

None

4

Color , Brushing pattern

Qualified

The color is consistent and the brushing pattern is not obvious

Observation and inspection

Excellent

Color Consistent, no brush marks

5

Bright and smooth

Qualified

Bright and even, smooth and unobstructed feel

< p>Observation and inspection

Excellent

Bright enough, smooth and smooth to the touch

6

Decorative lines and color separation lines are straight< /p>

Qualified

The deviation is not greater than 1mm

Pull 5m of wire (less than 5m of wire) and check with a ruler

Excellent

Straight

7

Doors, windows, hardware, glass, etc.

Qualified

Doors and windows are clean, hardware is pollution-free, glass, etc. Basic clean

Observation and inspection

Excellent

Clean

Note: (1) Equipment pipes are sprayed with silver powder, paint, and coating evenly , bright enough.

(2) Apply matte latex paint and matte mixed color paint without checking the brightness.

The quality of the surface where varnish is applied should comply with the requirements in Table 5.

Varnish Engineering Quality Inspection Items Table 5

Items

Items

Quality Standards

Inspection Methods< /p>

1

Missing brushing, peeling, stains

Not allowed

Observation and inspection

2

Wrapped edges, sagging and wrinkled skin

Qualified

No surface, no obvious small areas

Observation and inspection

Excellent

None

3

Color and brush pattern

Qualified

Consistent color and large brush pattern No surface, no obvious small surface

Observation and inspection

Excellent

Consistent color, no brush marks

4

Wood grain

Qualified

Brown eyes smoothed, wood grain clear

Observation and inspection

Excellent

< p>Brown eyes are smoothed and the wood grain is clear

5

Bright and smooth

Qualified

Bright and even, smooth and smooth to the touch

Observation and hand inspection

Excellent

Bright and soft, smooth and unobstructed feel

6

Decoration Line color and wood grain

Qualified

Decorative line color is uniform and wood grain is clear

Observation and inspection

Excellent

< p>Decorative lines are uniform in color, clear wood grain, clean and free of oil accumulation

7

Doors, windows, hardware and glass, etc.

Qualified

Doors and windows are clean, hardware is pollution-free, and glass is basically clean

Observation and inspection

Excellent

All clean

Note: (1) The large surface referred to in this section refers to the inside and outside of the door and window fixed furniture after they are closed.

(2) The small surface refers to the part of the applied surface that can be seen except the large surface.

(3) Apply matte latex paint or matte paint without checking the brightness.

Color spraying

Suitable for various indoor color spraying and roller coating decoration projects.

Guarantee items: The material variety, quality, and color of color spraying all meet the design requirements and have product certificates, and must be used according to the product combination. The base for color spraying must comply with the relevant provisions of this standard.

Basic items: Special primer should be used for the bottom layer of color spraying; the primer should be evenly coated, without any leakage, and the surface should be smooth. The coating film is firm and meets the requirements of Table 6.

Color spraying engineering quality inspection items table 6 items

Items

Quality standards

Inspection methods

1

Leakage, peeling, stains

Not allowed

Observation and inspection

2

Falling , wrinkled skin

Qualified

No large surface, no obvious small surface

Observation and inspection

Excellent

Not allowed

3

Color and pattern

Qualified

The color is consistent and the pattern is basically uniform

Observation and inspection

Excellent

Consistent colors and uniform patterns

4

Decorative lines and ruled lines

Qualified< /p>

The deviation is not more than 3mm

Pull a 5m line (less than 5m to pull through the line) and check with a ruler

Excellent

The deviation is not more than 2mm

5

Hardware, door and window glass, etc.

Qualified

Doors and windows are clean, hardware is pollution-free, and glass is basically pollution-free

Observation and inspection

Excellent

Clean and pollution-free

Finishing of joinery products This section applies to finishing of high-grade decorative joinery products and finishing of joinery products. For engineering, the range of paints used is: polyester, polyurethane, acrylic, nitrocellulose, and natural resin paints. Inspection quantity: Observation census, allowing 20% ??of the total number of random inspections of defect control items.

Guarantee items The variety, quality, grade, color, performance, etc. of the paint must comply with the design and relevant standards, and should be accompanied by product instructions.

The coating effect must match the sample. The plasticity and workability of the putty used in the paint should meet the construction requirements, and should be selected according to the performance of the primer and topcoat. Thinner should be used according to the properties of the film-forming substances in the paint.

Inspection method: Observe and check the rational performance certificate.

Basic items

The finishing and coloring quality of fine wood products should comply with the requirements in Table 7. ?

Table of quality inspection items for finishing and coloring of fine wood products Table 7