Illustration of phototherapy nail polishing steps

Illustration of the steps of phototherapy nail polishing

Illustration of the steps of phototherapy nail polishing. Phototherapy manicure is a manicure technology that uses a new technology. One of the most praiseworthy advantages is that it is environmentally friendly and environmentally friendly. The ingredients are healthy, and phototherapy manicure will not produce any pungent smell during the operation. The following is a diagram of the steps of polishing phototherapy nails. Illustration of the steps of phototherapy nail polishing 1

Phototherapy nail polishing process

A. The natural nail procedure for strengthening the glue structure (of course the nail has been repaired):

1 , engraving and polishing (pay attention to the edges and nail grooves before engraving and polishing in time)

2. Clean the surface of the fingernails with a special cleaning solution

3. Apply a thin layer of adhesive and bake for 30 seconds

4. Apply transparent (pink) glue (note that the edges and nail grooves do not need to be injected) and bake for 2 minutes (the outer edge should be wrapped with glue)

5. Apply Sealant, not too thin, bake for 2 and a half minutes

6. Clean with cleaning fluid

7. Apply nutritional oil

B. SMD nail polish:

1. Engraving and grinding

2. Top patch type, the surface of the patch type needs to be carved and polished

3 , clean the nail surface with cleaning fluid

4. Apply adhesive for 30 seconds

5. Apply completely transparent (pink) glue for 2 minutes (wrap the outer edge with glue ), polish and polish the manicure

6. Apply sealant and bake for 2 minutes

7. Clean

8. Apply nutritional oil

C. Colorful gel nails:

1. Engraving and grinding.

2. Use cleaning fluid to clean the nail surface.

3. Apply adhesive and bake for 30 seconds.

4. Place a paper backing board, use transparent glue on the outer edge and interconnection, bake for 2 minutes and pinch the crown.

5. Dip the colorful glue into the shell powder paint and apply it to the outer edge in a "Z" shape for 2 minutes.

6. Apply the glitter glue on your nails and bake for 2 minutes.

7. Polish, trim, and clean the nail surface.

8. Apply sealant and perform phototherapy for 2 and a half minutes. The outer edge needs to be wrapped.

9. Apply nutritional oil. If you need to paint or engrave, proceed at the end of step 7.

D. European nail polish:

1. Disinfection and sterilization

2. Remove nail polish

3. Carve and remove Ash

4. Use special cleaning fluid to clean the nail surface until it is naturally comfortable and clean

5. Install the paper backing board

6. Use a small amount of adhesive The mixture is applied on the nail surface from the root to the edge of the nail to form chromatography, and phototherapy is performed for 30 seconds. Phototherapy can be done on the other hand at the same time. (Too much adhesive will make it easy to fall off. You can do 4 fingers at a time. You cannot clean it after phototherapy.)

7. To make the outer edge, use a phototherapy pen to take a small amount of white or colorful extension glue. From the outside of the fingernail to the left side of the nail edge, the extension glue should not be too thick. Hold the pen on the side in a zigzag shape and skim off the unnecessary glue along the smile line of the extension glue. Apply light therapy for 2 minutes. Use a professional medical The tweezers are curved and cannot be cleaned after phototherapy.

8. Apply the pink extension glue on the nail. Penetrate the phototherapy pen into the pink extension glue and then remove it. Pull out a trace of the glue and connect it to the nail surface that needs to be repaired. Let it flow on the nail surface. Restoration, resulting in a smooth floor plan. Repeat this process on other nails, use a plastic pusher to remove the glue on the nearby skin and roots to avoid falling off, and treat with light for 2 minutes

9. Use a special cleaning solution to remove the remaining sticky matter. Remove the paper backing board, rotate the consumer's hand back, and phototreat the back of the fingernail for 1 minute.

10. Clean your fingernails, use a white file to create ideal lines, and remove dust

11. Apply super-effective sealant chromatography to the nail surface to prevent contact. Skin, phototherapy for 2 and a half minutes.

12. Use special cleaning fluid to remove residue again

13. Apply nutritional oil and massage the roots to make the nail surface smooth and flawless. Illustration of phototherapy nail polishing steps 2

Method/step

Remove dead skin, use a dead skin pusher to shovel up the dead skin on the finger edge, and use a dead skin shear to cut off the shoveled dead skin Lose. (Removing dead skin is the key to doing a good phototherapy manicure. If the dead skin is not removed completely, the phototherapy manicure will easily become warped)

Manicure, manicure has There are two places to repair. One is to polish the surface of the nail. The surface of human nails is smooth and contains oil. It must be polished quickly, otherwise the phototherapy nails will not stick well. The second is to cut the front edge of the nail short and use a sanding bar to shape the front edge of the nail into an arc that matches the front edge of the paper support.

After polishing, use a dusting brush to remove dust, and use a cotton pad dipped in a certain amount of cleaning solution to clean the nail surface.

Take a small amount of phototherapy primer and apply it on the polished nail surface. After applying the primer, illuminate the light for 3 minutes

Apply the phototherapy glue, and use a phototherapy pen to take an appropriate amount of phototherapy glue. Apply it on the nails to create the desired shape and length, put it in a phototherapy lamp and illuminate it for 3 minutes to solidify.

Repeat step 4, applying the phototherapy glue twice will make it more resistant to falling off.

Apply no-rinse sealant. Apply a small amount of sealant to the surface of the carved and polished nails and illuminate with light for 3 minutes. This completes the phototherapy gel.

Illustration of phototherapy nail polishing steps 3

Phototherapy nail polishing steps

Materials required for making phototherapy nails

Phototherapy machine, phototherapy set (combination agent/extension paste/model glue/super bright sealer), cleaning gel, phototherapy pen, phototherapy color glue (pink)

Basic phototherapy nail production steps

1. Before doing nails, be sure to make a good nail base. First, roughen the nail surface.

2. Next, use a polishing stick to polish the "surface" of your nails to smooth out the uneven texture on the surface of your nails. On the one hand, it can make the mirror effect of subsequent phototherapy more flawless. On the other hand, it can remove the oil on the surface of the nail, making the phototherapy glue and the nail adhere more firmly.

3. Then, apply a thin layer of bonding agent evenly, put it into the phototherapy machine for 30 seconds and then take it out.

4. Apply pink sequin glue evenly, make a two-thirds gradient, put it into the phototherapy machine for 30 seconds and then take it out.

5. Apply model glue, put it into the phototherapy machine for 50 seconds and then take it out. Then use a pinch strip to remove the glitter protrusions and shape the nails according to your personal preference. In this way, the beautiful phototherapy nails are completed.

Note: The glue should be applied evenly and the adhesive and sealant should not be too thick. When applying glue, use the pen smoothly and do not apply it to the skin. The complete phototherapy nail treatment is complete.