Let's have a look. What other bathroom cabinet installation knowledge do you not know?

The beauty of the bathroom is inseparable from the bathroom cabinet. After all, there are too many toiletries to keep the bathroom clean and beautiful, so the bathroom cabinet is very important. Then let's take a look at the installation steps and acceptance criteria of bathroom cabinets!

First, understand the common problems in the installation process.

(1) The difference between drainage and surface drainage

1. For wall drainage, the installer will affect it on the spot.

2. For ground drainage, it is divided into.

(1) The cabinet has no drawers.

Floor hole location. Reserved on the backplane.

(2) The cabinet contains drawers.

The factory will change the internal shape of the drawer to leave the ground drainage position.

(3) the ground is not balanced

Installers can use and handle plastic mats.

Second, the bathroom cabinet installation punching method

1. Prepare the following tools for punching ceramic tiles: lithium battery hammer, glass drill, water, cement nail and sealant.

2. Choose a suitable position on the perforated tile, and check whether the tile is empty to avoid punching holes in the empty tile.

3. Before tiling, seal the tiles with glue now, which helps to locate the punching position and prevent the tiles from cracking.

4. Cut a small point at the cutting position of ceramic tile with cement nail first, which can prevent the bit from slipping when drilling.

5. When preparing for drilling, first set the electric hammer to the flat drilling mode, and then turn on the switch. The flat drilling mode rotates slowly during drilling, and then drives the hole to.

Three, ceramic tile wall drilling matters needing attention

1, when all your tiles are perforated, you need to add water when you play, but when the tiles are cold, you can only punch them.

2. If the ceramic tile is cracked seriously, it can be repaired with toothpaste. Find a series of toothpaste with the same color as the ceramic tile, squeeze out some, spread it evenly on the gap, and then wipe off the excess toothpaste until it dries. You can hide the cracks.

3. For the expansion bolt drilled in ceramic tile, select the width of the hole according to the size of the bolt.

4. When the ceramic tile is perforated, water drips when the ceramic tile is perforated, which can prevent the ceramic tile from cracking due to the heating caused by the perforation.

5. The ceramic tile cracks in the stamping process, which can be cracked and repaired according to the imagination. If there are only a few small cracks that do not affect the use, you can use glass glue to add cracks, which can avoid black cracks and make the tiles ugly.

6. When drilling, be sure to stick the seal on the surface of the ceramic tile, because this can prevent the porcelain glaze on the surface of the ceramic tile from slipping off during drilling, causing the ceramic tile to break, and also prevent the drill bit from leaving the drilling position and scratching the surface of the ceramic tile.

Fourth, the installation steps

(1), installation method of main cabinet.

1. Installation method of wall-mounted bathroom main cabinet

First of all, check whether the wall is firm (otherwise, use floor-standing type). According to the selected hole position, punch holes in the wall with an impact drill (the installation table is 80-83cm above the ground, which can also be adjusted according to the height and habits of residents). Plug the plug into the plug on the wall, and then lock the cabinet on the wall with tapping screws (expansion screws can also be used for installation). After the cabinet is installed, adjust the levelness by aligning the basin with the wood of the cabinet.

2. Installation method of floor-standing bathroom cabinet

Place the cabinet horizontally, screw the cabinet base assembly to the fixing piece through stud screws, and then put the flat cabinet in a proper position, with the cabinet base on the outside to make the cabinet balanced, and adjust it to the level through grounding screws for stable placement.

(2) Installation methods of payment cabinets and shelves

According to the selected hole position, punch a hole in the wall with an impact drill, insert the plug into the wall, and then lock the wall with self-tapping screws. After installing the cabinet, adjust the release plane.

(3) Installation method of bathroom mirror

1. Measure the size of the mirror with a tape measure, then insert the wall plug into the appropriate position of the wall according to the installation specifications, and then screw the screws into the wall to an appropriate depth.

2. Insert the tapping screw into the wall according to the two holes on the back of the mirror.

(4) Installation method of basin

1, installation process

Insert the expansion bolt → twist → hang the washbasin pipe rack → put the washbasin on the shelf to find the water level → receive water: washbasin → straighten → receive water.

2. Installation method

(1) When installing the pipe rack washbasin, draw a vertical line according to the centerline of the sewer outlet, measure the height upward from the ground, draw a horizontal line on the wall, and draw a mark on the wall according to the width of the washbasin, with a diameter of 120mm. Stay away from brick slag and other sundries in water punching. Insert the expansion bolt into the hole, crush it with cement, hang the thin tube rack, put the rubber pad on the bolt and eye socket, put the nut on it, and screw it into the basin fixing hole of the end cover of the elastic medium pipe rack. Put the washbasin on the shelf to find a plane, weld the bolt with a diameter of 4 mm on the horizontal iron bar, insert the upper end into the fixing hole, and insert the lower end into the pipe rack. Nuts, twist to medium.

(2) Install the cast iron washbasin, draw a vertical line according to the center of the sewer, measure the height upward from the ground, draw a horizontal line as a crosshair, mark the horizontal line, wash the washbasin according to the width, and then mark the horizontal line. Draw a vertical line for each one, put it on the shelf in the pot and draw the position of the hole. Introduce the roll-in hole, fix the flowerpot on the shelf on the wall with screws, put the washbasin on the shelf, and move the shelf with bolts. Open and pull out the movable frame, hook the frame in the hole, then tighten the movable frame screw and level it to find it.

(5) Installation method of sewer pipe

1. Wall drainage.

The reserved hole on the sewer wall should be 50~55CM from the ground, in the middle of the cabinet.

2. Ground drainage.

Just leave a hole in the middle of the cabinet, but not too far from the wall.

(6) Installation method of inlet pipeline

The outlet of the hot and cold water inlet pipe can be located in the middle of the cabinet, but it should be between 45~50CM or slightly above the ground. No entry.

(7) Installation method of rearview mirror headlights

The outlet of the wire should be about 200CM from the ground and placed in the middle of the bathroom cabinet.

Verb (abbreviation of verb) installation precautions

(1), the height of attention.

Whether it is a stand-alone or washbasin, the height of the basin surface or table top is 80-85 cm, because too short basin will lead to low back pain.

(2) Pay attention to completion.

The edge of the washbasin must be slightly higher than the countertop, but the connection with the countertop must be smooth. The purpose is to prevent the water splashed on the countertop from being rubbed back into the pool and to facilitate the cleaning of the countertop. The mesa itself must use curved surfaces. Smooth materials, edges and two corners must be smooth to avoid. Smoothness of washbasin itself. The high water level of the pool makes it difficult for the water in the water to adhere to the water surface, reducing the number of times to scrub.

(3), pay attention to the depth and faucet.

Traditionally, the depth of washbasin is directly proportional to the water flow intensity of faucet, which is higher than installation, that is, deep basin can only be installed. The faucet is. Ten thousand, the bottom can't be light, for.

Installing a thick faucet in the swimming pool will make people splash on themselves. The bottom of the pool should have enough radian, not too flat, or water will accumulate.

Acceptance criteria of intransitive verbs

(1), flat: the upper edge of all sanitary equipment should be horizontal, the height of appliances in the same room should be consistent, the allowable deviation should be less than 5mm, and the allowable deviation of installation verticality should be less than 3 mm.

(2) Stability: After the equipment is installed, there should be no jitter.

(3) Prison: After installation and use for a period of time, it should be resolutely prevented from loosening.

(4) Accuracy: the coordinate position, elevation size, drainage outlet and drainage outlet of sanitary ware shall be accurate.

(5) No leakage: the connection on the sanitary ware and the connection of the drain must be tight and watertight.

(6) Easy to use: The installed sanitary ware should be arranged according to different objects and the position should be reasonable. The valve handle should be oriented and the whole set of facilities should be beautiful.

(7) Good performance: the valve and nozzle switch are flexible.