Traditional Culture Encyclopedia - Photography major - How to make remote control boat?

How to make remote control boat?

Remote control boat is the first choice for outdoor toys. Some netizens would rather make their own remote control boat than buy finished products. So, how to make remote control boat? How to make remote control boat? First, prepare a drawing of the ship, make the shape of the ship you like, then stick the steering motor, weld the wires on it with an electric soldering iron, and then make the remote control receiver, power system and steering. Next, let's take a look at Bian Xiao DIY homemade remote control boat production tutorial. How to make remote control boat?

Method 1:

1. Print a drawing of a ship online, just follow the drawing, and then use balsa Balsa to make a ship.

2, adhere to the steering motor, must be strong twist. Weld the wire on it with an electric soldering iron!

3. Make a remote control receiver. Glue the rod antenna first, and then the remote control receiver.

4. Make the power system. Stick on the motor and start wiring. Next to the motor, drill two small holes with an electric drill to lead out the wire, and stick it with hot melt adhesive to seal it. The interior of the ship is also bonded with hot melt adhesive.

5. Turn. Prepare a small piece of wood. The harder the better. Stick it on the front motor. The steering angle must be limited. So, prepare a toothpick, cut it in half and stick it next to it.

6. Then start to place the battery and prepare the remote control transmitter.

After trial, this remote control boat has the following advantages:

1, strong sealing (very important);

2. Long remote control distance;

3. Flexible steering;

4, freely before and after;

5, the appearance is good.

Method 2:

Main materials: acrylic board, motor, fixed plastic strip, metal fixing frame, red paddle, 2 150*2mm shafts, M2/M3 screws and nuts, and 2 6*8mm worms.

Tools: ruler, screwdriver.

Production steps:

1. Fix the plastic strip with M3 screws and nuts. Pay special attention here. It's fixed on the right. Don't fix it wrong. One side with two holes is on a triangle.

2. Then continue to use M3 screw to fix a new plastic frame on the hypotenuse, but this time it is fixed with a single hole. Note that the hypotenuse is fixed on the hull, not the right angle.

3. Then start loading the hull. First, install 130 fixing frame on the hull. When fixing, don't fix it completely, just fix it at an angle. In order to put the motor in the back conveniently, M2 screw is used here.

4. Insert the worm before fixing the motor on the fixing frame, and then install the worm after fixing. The difficulty is unusual, so don't try if you are curious. This step is actually to repair the motor.

5. Fix the other two plastic fixing strips on the hull. Remember that they are fixed with double holes. They are double-perforated. If it is not fixed correctly, it will be very embarrassing in the back.

6. This step is to insert the shaft into the worm, and the worm passes through the plastic strip.

Method 3:

1, find a picture of your favorite ship.

2. Use your space imagination to draw the plan of the ship on paper, save the details and only draw the main body.

3. Cut it with scissors according to the contour line, and then put it together. See if it looks like the boat in the picture.

4. Try several times to find the plane development diagram that is most similar to the ship in the photo.

5. Stick this picture on a 0.3-0.5mm thin iron sheet (aluminum sheet is ok, but it is not easy to weld), cut it with scissors according to the contour line, put it together, weld the joint firmly and then paint it.

6. Cut a small round iron sheet into the shape of three blades of the fan, each blade is bent at an appropriate angle in the same direction, with a hole in the middle, and a bicycle steel wire with an appropriate length is vertically welded as the propeller and rotating shaft.

7. Find an old rod antenna (ballpoint pen core can also be used) and cut a section (bicycle steel wire can be freely rotated in it) as a shaft sleeve.

8. Find a toy motor, weld it on the bracket, fix it in a suitable position in the cabin, connect and assemble the parts, and check whether there is water in the bathtub before the sea trial can be officially carried out.