Emergency plan to prevent thunderstorm weather

Emergency plan to prevent thunderstorm weather

In normal study, work and life, unexpected events are not allowed. In order to avoid more serious consequences, it is often necessary to make emergency plans in advance. How to write an emergency plan? The following is my carefully prepared emergency plan to prevent thunderstorm weather. Welcome to read the collection.

Emergency plan for preventing thunderstorm weather 1 In order to prevent lightning and rainstorm from harming the safety of mine facilities and personnel in rainy season, strengthen the work of lightning protection and rainstorm prevention in coal mines, establish an efficient and orderly disaster relief organization, improve the overall level of disaster prevention work, and prepare for disaster prevention work in our mine quickly and efficiently, the emergency plan for lightning protection and rainstorm prevention is specially formulated.

I. Scope

This plan is applicable to lightning protection and rainstorm emergency work within the mining area of Xuzhou Li Tang Mining Co., Ltd.

Second, the organization and responsibilities

1, emergency organization system

Set up a leading group for lightning protection and rainstorm prevention, be responsible for the leadership of lightning protection and rainstorm prevention in this mining area, and supervise and inspect the lightning protection and rainstorm prevention work. Responsible for the rescue of sudden lightning storm disasters, the team members must quickly rush to the relevant posts to direct the handling of problems. Team members are required to be familiar with the on-site working environment and have the ability to deal with unexpected problems in time.

Team leader:

Deputy team leader:

Members:

2. Specific responsibilities

(1) Be responsible for studying and formulating specific measures and opinions on lightning protection and rainstorm disaster work arrangement and accident emergency treatment in this area;

(2) Responsible for the emergency support and response to lightning and rainstorm disasters;

(3) Responsible for joint inspection, quality supervision and acceptance of lightning protection and rainstorm prevention;

(4) Responsible for the handling, rescue and accident aftermath of lightning and rainstorm disasters;

(5) Responsible for the construction and management of lightning protection and rainstorm accident handling team;

(6) Responsible for organizing the deployment of personnel and materials;

(7) In case of serious disaster, take countermeasures and report to the superior in time.

Three, disaster prevention requirements and points

In the case of lightning and rainstorm, according to the actual situation of thunderstorm, the leader of the emergency plan team decided to release the start and end time of the emergency plan for lightning protection and rainstorm prevention in our mine and organize its implementation. Relevant personnel are on standby at any time to ensure the safety of life and property of employees in our mine.

IV. Safe implementation of lightning protection and rainstorm prevention

1. According to the specific conditions of the company's buildings and related facilities, check the connection between the existing lightning protection devices and the metal objects on the roof, whether the down conductor is broken or corroded, whether the soil near the grounding device sinks, and whether the drainage pipeline is blocked. Clean all flood discharge pipes to ensure smooth flow.

2. Conduct annual inspection of all lightning protection products and facilities. Do a good job in the daily maintenance of lightning protection devices, and designate a special person to be responsible.

3. During a thunderstorm, employees in the factory are forbidden to walk near high-voltage lines to prevent high-voltage discharge from hurting people.

4. In case of lightning, when the high-voltage line is disconnected from the ground, contact Fengxian Power Supply Bureau for power outage and evacuate people as soon as possible. Don't go near the break point within 30 meters, and evacuate employees in an orderly and organized manner.

5. In case of water disaster, the personnel on duty should report to the planning team in time, and the members of the planning team should be under unified command and assume their respective responsibilities.

6. Install submersible pump in the cable trench of the ground substation, and drain the water into the main drainage ditch in time when the accumulated water is serious.

7, rainy days, mechanical and electrical personnel on duty to inspect the factory, the focus is on the substation and distribution station.

8, thunderstorm days must arrange personnel on duty in the substation, to ensure the normal power supply.

9, the rainy season three prevention materials must meet the requirements. Mainly check the implementation of water pumps, drainage pipes, switches, cables, iron hoists, woven bags, raincoats, rain boots, canvas, miner's lamps, safety helmets and other materials, and hang special cards for management.

10, before the thunderstorm season comes, the hidden dangers of double-circuit power supply lines must be handled well:

(1) Cut down trees that pose a threat to the power supply line along the way to prevent the power supply line from tripping due to grounding or short circuit caused by contact between overhead lines and trees in thunderstorm weather;

(2) Replace defective porcelain bottles and stay wires;

(3) All lightning arresters must be tested and qualified.

1 1. Check the lightning rods, lightning wires and grounding grids of all buildings, and take measures to rectify those that do not meet the requirements.

12. If the grounding resistance is greater than 2 ohms, salt or other measures must be taken to reduce the resistance to below 2 ohms.

13. In case of frequent lightning and rainstorm, the personnel on duty of the preplan team shall be responsible for starting and stopping the main and auxiliary winches according to the weather conditions.

14. During the thunderstorm, the leading group of emergency plan work should arrange inspection, and the responsible person should rectify the existing problems within a time limit.

Five, 35KV ground substation emergency plan

(1) facility maintenance

Power accidents are mainly prevented, and the main equipment in the substation should be regularly maintained and inspected. The main measures are as follows:

1, quoted from the 35KV two-way mine power supply of Litang Coal Mine ground substation (the first Li I line and I line), to ensure the first run, and the other one must be hot standby.

2, do a good job of 35KV substation equipment maintenance, to ensure that the equipment platform in good condition.

3. Patrol the lines beyond 35KV once a month to ensure the normal power supply of the power supply lines from Shouxian Substation and Shunhe Substation to Litang Coal Mine.

4. Strengthen the contact with the superior substation and the dispatching room of Fengxian Power Supply Bureau.

5, the personnel on duty strictly implement the power supply technology operating rules and the rules and regulations of the substation.

6, in strict accordance with national standards, according to the provisions of equipment performance testing.

7. Regularly set and check the relay protection to ensure that the protection is sensitive and reliable.

8, found that the equipment anomalies or defects should be timely investigation and handling, leaving no hidden dangers.

(2) Normal operation mode of the line

There is a ground substation in the ground industrial site of Litang Coal Mine, in which two power sources (the first I line) are led out from Zitong 1 10kV substation, and the other route is led out from Shunhe 1 10kV substation (Li Shun I line). The line is overhead, the conductor is LGJ- 185, and the length of the line. 8 kilometers, 13. 2 kilometers.

(3) Active lines and emergency response to accidents

Active power lines: the first Li I line in Litang Coal Mine supplies power and the Li Shun I line in Litang Coal Mine supplies power.

Accident emergency: When the primary circuit is out of power, the faulty line should be cut off quickly and the active line in the other circuit should be connected.

(4) Substation accident power failure

If the first Li I line (or I line) in Litang Coal Mine can't restore power supply temporarily after power failure, it is necessary to switch the switch in time to supply power to the I line (or I line) movable line in Litang Coal Mine.

In case of power failure of Li Shun I Line (or Juri I Line) in 35KV Litang Coal Mine, the personnel on duty should first determine the cause of the accident, deal with it quickly, and report the situation to the mine operation department and superior leaders. If the accident line is the power supply network in the mine, the accident network should be removed first, and then the power supply should be restored; If the superior substation loses power or the line fails, another line should be activated immediately.

The specific operation steps are as follows:

Li Shun I line accident power outage operation:

1, turn off switches 35204, 35203 and 10206, and confirm the disconnection;

2. Check whether the incoming switching power supply of 35 104 is charged and confirm that it is charged;

3. Confirm that the incoming switch handcart of 35 104 is in the working position;

4. Turn on the 35 104 switch and confirm that it is closed;

5. Check whether the instructions of 35 104 switching power supply are normal and confirm that they are normal;

6. Confirm that the 35 103 switch is in the working position; Close the switch 35 103 and confirm that it is closed;

7. Check whether the 1 # 5000 kva transformer works normally, and confirm that it is normal;

8. Check whether the 10KV 10 105 incoming line cabinet and the original 10KV feeder cabinet are closed, and confirm that they are in normal working condition.

Emergency power outage operation of Shouli Line 1:

1, turn off switches 35 104, 35 103, 10 105, and confirm the disconnection;

2. Check whether the incoming switching power supply of 35204 is charged, and confirm that it is charged;

3, confirm the 35204 incoming switch handcart in the working position;

4. Turn on the 35204 switch and confirm that it is closed;

5. Check whether the instructions such as 35204 switching power supply are normal and confirm that they are normal;

6, confirm the 35203 switch in the working position; Turn on the 35203 switch and confirm that it is closed;

7, check whether 2 # 5000 kva transformer works normally, and confirm its normal;

8. Check whether the 10KV 10206 incoming cabinet and the original 10KV feeder cabinet are closed, and confirm that they are in normal working condition.

After emergency power failure and brake switching operation:

Restore the power supply of each power supply location, and contact the superior substation and the dispatching room of Fengxian Power Supply Bureau until the equipment runs safely and normally. After confirming that it is normal, put the first Li I line (or I line) and main transformer in Litang Coal Mine into hot standby state.

Six, 35KV substation belongs to the main load emergency plan

(a) the main shaft winch room high voltage power failure emergency plan

1. If the power supply of line I (or line II) of the main shaft winch room cannot be restored temporarily after power failure, the brake must be switched in time to supply power to the active line of line II (or line I) of the main shaft winch room.

When the power supply of line I (or line II) in the main shaft winch room is out of power, the personnel on duty should judge whether it is an accident or other reasons in a very short time, deal with it quickly, and report the situation to the mine dispatching room and superior leaders. If the person on duty judges that it is an accident trip, the equipment or line at the accident point should be cut off first, and the other circuit power supply should be activated immediately.

The specific operation steps are as follows:

Main shaft winch room I line accident power outage operation:

(1) Confirm that the power supply of spindle I line is in the off position.

(2) Confirm that the handcart of 10209 spindle II line is in the closing position.

(3) Close the spindle 10209 line II.

(4) Restore the normal power supply of the spindle II line.

(5) Check the fault cause of spindle I line, and put the power supply into hot standby after it is confirmed to be normal.

Main shaft winch room II line accident power outage operation:

(1) Confirm that 10209 spindle II power supply is in the off position.

(2) Confirm that the I handcart of the spindle 10 109 line is in the closing position.

(3) close the spindle 10 109 line I.

(4) Restore the normal power supply of spindle I line.

(5) Check the fault cause of spindle II line, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) Turn all switches of the spindle winch to the stop position immediately.

(2) Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply, and resume main shaft hoisting after repair.

(2) Emergency plan for winch room during high-voltage power failure

1. If the power supply of line I (or line II) of the auxiliary shaft winch room cannot be restored temporarily after power failure, it must be supplied to the active line of line II (or line I) of the auxiliary shaft winch room in time.

When the power of line I (or line II) in the auxiliary winch room is cut off, the personnel on duty should judge whether it is an accident or other reasons in a very short time, deal with it quickly, and report the situation to the mine dispatching center and superior leaders. If the personnel on duty and electrical maintenance personnel judge that it is an accident trip, they should first cut off the equipment or lines at the accident point and immediately activate the other circuit for power supply.

The specific operation steps are as follows:

During the power failure operation of I-line accident in winch room:

(1) Confirm that 10 108 auxiliary shaft I line power supply is in the off position.

(2) Confirm that the handcart of 10208 countershaft II line is in the closing position.

(3) Close the auxiliary shaft 10208 line II.

(4) Restore normal power supply of auxiliary shaft II line.

(5) Check the fault cause of the auxiliary shaft I line, and put the power supply into hot standby after it is confirmed to be normal.

Emergency power failure operation of line II of auxiliary winch room:

(1) Confirm that the auxiliary shaft II power supply at 10208 is in the OFF position.

(2) Confirm that the handcart of 10 108 countershaft I line is in the closing position.

(3) Close the auxiliary shaft I line 10 108.

(4) Restore normal power supply of auxiliary shaft I line.

(5) Check the fault cause of the auxiliary shaft II line, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) Turn all switches of the auxiliary winch to the stop position immediately.

(2) Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply, and resume auxiliary shaft hoisting after repair.

(3) Emergency Plan for High Voltage Power Failure of Box Transformer in Compressor Room

1. If the power supply of line I (or line II) of the box-type transformer in the air compressor room cannot be restored temporarily after the power failure, the switch should be switched in time to supply power to line II (or line I) of the box-type transformer in the air compressor room.

When the power supply of line I (or line II) of box-type transformer in air compressor room is cut off, the personnel on duty should judge whether it is an accident or other reasons for power failure in a very short time, deal with it quickly, and report the situation to the mine dispatching room and superior leaders. If the person on duty judges that it is an accident trip, the equipment or line at the accident point should be cut off first, and another loop power supply should be started immediately.

The specific operation steps are as follows:

Accident power failure operation of box transformer I line in compressor room;

(1) Confirm that 10 102 compressor room box transformer I line power supply is in the off position.

(2) Confirm that 10205 compressor room box transformer II line handcart is in the closing position.

(3) Close line II of box transformer in 10205 air compressor room.

(4) Restore the normal power supply of box transformer II line in compressor room.

(5) Check the failure cause of I-line of box-type transformer in compressor room, and put the power supply into hot standby after it is confirmed to be normal.

Emergency power failure operation of box transformer II line in compressor room:

(1) Confirm that 10205 power supply of box-type transformer in air compressor room is in the off position.

(2) Confirm that 10 102 compressor room box transformer I line handcart is in the closing position.

(3) Close 10 102 compressor room box transformer I line.

(4) Restore the normal power supply of I line of box transformer in compressor room.

(5) Check the failure cause of box transformer II line in compressor room, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) Turn all switches of the air compressor to the stop position immediately.

(2) Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply and resume operation after the compressor is repaired.

(4) Emergency plan for power failure of wind turbine room

1. If the power supply of line I (or line II) of the fan room cannot be restored temporarily after power failure, the switch must be switched in time to supply power to the active line of line II (or line I) of the fan room.

When the power supply of line I (or line II) of the wind turbine room is out of power, the personnel on duty should judge whether it is an accident or other reasons in a very short time, deal with it quickly, and report the situation to the mine dispatching room and superior leaders. If the person on duty judges that it is an accident trip, the equipment or line at the accident point should be cut off first, and another loop power supply should be activated immediately.

The specific operation steps are as follows:

Operation of I-line emergency power outage in the fan room:

(1) Confirm that the power supply of I line of fan in low-voltage 400v distribution room is in the off position.

(2) Check whether the power supply of line II of fan in low-voltage 400V distribution room is charged, and confirm that it is charged.

(3) Close the low-voltage 400V transformer room fan II line power switch circuit breaker.

(4) Restore the normal power supply of fan II line.

(5) Check the cause of fan I line failure, and put the power supply into hot standby after it is confirmed to be normal.

Emergency power failure operation of line II of the wind turbine room:

(1) Confirm that the power supply of line II of the fan in the low-voltage 400v distribution room is in the off position.

(2) Check whether the I-line power supply of the fan in the low-voltage 400V distribution room is charged and confirm that it is charged.

(3) Close the low-voltage 400V transformer room fan I line power switch circuit breaker.

(4) Restore the normal power supply of fan I line.

(5) Check the fault cause of the fan II line, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) Turn all switches of the main fan to the stop position immediately.

(2) Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply and resume operation after the main fan is repaired.

When a 35KV total power failure accident occurs, shaft maintenance personnel such as Gao Ming, Han, Song Huaidong and Zhang Fusong must quickly arrive at the main shaft site, open the explosion door of the main shaft, and implement natural ventilation to ensure the safety of underground ventilation.

Emergency plan for preventing thunderstorm weather 2 In order to prevent, avoid and mitigate lightning disasters, ensure the safety of campus teachers and students' lives and campus equipment and property, and put an end to accidents caused by lightning disasters, this plan is formulated according to the spirit of relevant documents of the Ministry of Education and China Meteorological Bureau on preventing meteorological disasters, as well as the detailed rules of Fujian Province's "Measures for the Management of Lightning Protection and Disaster Reduction", combined with the actual situation of our school.

I. Organizational structure

1, emergency leading group:

Responsibilities: Responsible for organizing, coordinating and inspecting the lightning protection work on campus, mastering the dynamic situation of lightning protection work on campus, putting forward preventive countermeasures and measures, and earnestly strengthening the leadership of lightning protection work. Formulate emergency plans and improve emergency mechanisms. Set up a lightning protection emergency rescue team attended by the main leaders of the campus and the person in charge of the office. In the event of an accident, the emergency plan for lightning protection shall be ordered to be started, and decisions and instructions shall be made in time to organize and direct the disposal work according to the instructions of the superior and the on-site situation.

2. Emergency Working Group

(1) Early Warning Information Group:

Responsibilities: Collect and sort out all kinds of information, pay attention to meteorological analysis, grasp lightning disaster information in time, conduct analysis and research, and provide basis for leadership decision-making. When lightning accidents happen, keep abreast of the progress of lightning protection emergency treatment and report information to superiors and subordinates.

(2) On-site disposal group:

Responsibilities: Investigate and collect information such as the cause, current situation and development trend of the incident in time, and report to the leading group; Evacuate personnel, clean up the scene, rescue the wounded, minimize losses and quickly control the spread of the situation; Protect all kinds of evidence in time according to the situation on the spot.

(3) security group:

Responsibilities: Be responsible for guarding the scene of the accident, evacuating people and vehicles, maintaining order at the scene, preventing irrelevant personnel from entering the scene, and cooperating with the medical and public security departments for rescue to prevent the situation from expanding.

(4) Logistics Support Group:

Responsibilities: Responsible for ensuring the mobilization of vehicles and personnel at the disposal site and the supply of tools, equipment and materials.

Second, the safety precautions

1, to raise awareness of the importance of campus lightning protection. The lightning protection work will be included in the important agenda of the campus. According to the seasonal characteristics, the preventive measures will be actively studied and the lightning protection work plan will be implemented.

2. Intensify publicity and education, and improve the lightning protection awareness and ability of teachers and students. Each campus should combine the publicity and education of lightning protection knowledge with other safety education on campus, strengthen the education of lightning protection safety knowledge for teachers and students in various forms, angles and levels, carry out emergency plan drills, hold lectures on lightning protection knowledge, carry out lightning protection knowledge consultation, and master various preventive methods in case of lightning emergencies. Comprehensively improve the legal lightning protection, scientific lightning protection, active lightning protection awareness and self-help and self-protection ability of teachers and students. All campuses should strengthen the training of campus lightning protection staff and strive to improve campus lightning protection ability.

3, do a good job of lightning protection safety inspection.

(1) Install lightning protection facilities as required, formulate inspection and maintenance system for lightning protection devices, and arrange personnel with lightning protection and electrical knowledge to be responsible for daily inspection and maintenance. Before and after the thunderstorm season, the inspection should be strengthened to eliminate the fault of lightning protection device in time.

(2) Consciously accept the detection service of lightning protection center of meteorological department and obtain the detection certificate of lightning protection device in Shaanxi Province. A new building shall have a test report issued by the lightning protection device testing institution.

(3) Regularly check the circuit and fence of the campus school building, and rectify the hidden dangers in time to ensure the safety of the campus school building when lightning strikes.

(4) For the libraries, computer rooms, laboratories and other departments and offices on campus, regular inspection and protection should be done, with special attention paid to the safe storage of chemicals and lightning protection.

(5) Establish a ledger of lightning hidden dangers, dismantle all unsafe facilities and take effective measures to eliminate hidden dangers.

Third, emergency measures.

1. In case of lightning accident, the discoverer shall immediately report to the campus lightning protection emergency work leading group; Call 1 10, 1 19 for first aid. In case of casualties, fire and explosion, the site should be protected and rescue personnel and property should be organized quickly.

2. After the accident, the leading group and the on-site disposal team should arrive at the scene of the accident at the first time, and base themselves on self-help or rescue according to the formulated emergency rescue plan;

(1) When lightning causes casualties, fires and explosions, measures such as fire fighting, medical rescue and personnel evacuation should be implemented in time to ensure the personal safety of teachers and students;

(2) Quickly control the hazard source, inspect and monitor the hazards caused by the hazard source, and determine the hazard area and degree of the accident;

(3) Immediately report the disaster to the safety emergency leading group of the District Education Bureau;

(4) protect the site;

(5) Ensure that the communication equipment is in good condition, and the main information inside and outside, up and down is in smooth contact.

3. When the heart activity and breathing of the person knocked down by lightning stop, artificial respiration and external heart massage should be adopted for rescue, and at the same time, 120 should be called for help as soon as possible.

4. When the computer network fails due to lightning strike, in addition to checking the damage degree of online equipment, it is also necessary to conduct a comprehensive inspection of the network equipment and computers that are not in working condition, so as to find out the problems in time and take corresponding measures to deal with them in time to minimize the losses.

5. For major lightning accidents, the campus should report the time, place, causes, consequences and measures taken to the safety emergency leading group of the District Education Bureau and the safety and stability management office of the District Education Bureau as soon as possible after the accident. The campus duty telephone and the school (park) director's mobile phone are opened 24 hours a day, effectively sending out information and reporting information.

6, to participate in emergency rescue personnel, under the unified command of the accident emergency leading group to carry out rescue, shall not delay, prevarication, effective measures should be taken to reduce accident losses, to prevent the spread of accidents.

Fourth, matters needing attention

1. After the accident, it is necessary to consider in advance whether power, gas and water should be cut off during the disaster relief process to avoid secondary disasters.

2. If the building is seriously damaged due to lightning strike, it shall notify the relevant departments for safety appraisal and evaluation.

3, when a lightning fire, start the corresponding fire emergency plan.

4. Implement the accountability system. For those who fail to perform safety duties according to law, violate safety regulations or disobey orders and arrangements in the emergency process, resulting in serious consequences, the campus shall give administrative disciplinary sanctions or other sanctions to those responsible in accordance with relevant regulations. Accidents that have adverse effects due to dereliction of duty or management out of control shall be punished by the relevant administrative departments and public security organs according to law. If a crime is constituted, criminal responsibility shall be investigated according to law.

Emergency Plan for Thunderstorm Prevention 3 This plan is formulated to prevent, avoid and mitigate lightning disasters, ensure the life of campus teachers and students and the safety of campus equipment and property, put an end to accidents caused by lightning disasters and ensure the normal work of the school.

I. Guiding ideology

Based on the principle of "people-oriented, safety first, prevention first", we will take active and effective measures to increase publicity and education, improve the safety awareness and preventive ability of teachers and students, and ensure the safety of teachers and students in our school.

Second, the emergency leading group and related institutions

In order to strengthen the prevention of lightning disasters in rainy season, strengthen leadership, and achieve early detection, early reporting and early prevention, a lightning protection safety leading group is established.

Team leader: Li Jinliang

Deputy team leader:

Team member: class teacher.

Three. Preventive measures and measures

1, carefully check the installed lightning protection facilities, find problems in time, and rectify them in time.

2. The lightning protection facilities of buildings include lightning induction of direct lightning (including side lightning) and lightning wave intrusion protection.

Direct lightning refers to the direct lightning strike on any part of the building above the ground, resulting in electrical effect, thermal effect and mechanical force. The protection facilities for direct lightning strike are mainly to protect the building itself from damage and reduce the various influences on the building space when the huge lightning current leaks into the earth along the building during lightning strike; Lightning induction refers to electrostatic induction and electromagnetic induction on nearby conductors during lightning discharge, which may cause sparks between metal parts; Lightning wave intrusion refers to the action of lightning on overhead lines or metal pipelines, which may invade houses along these pipelines, endanger personal safety or damage equipment. In view of the above, pay attention to the following links.

1. Lightning protection of buildings: check whether lightning protection facilities and equipment are perfect and intact, and whether the building itself is connected with external metal objects.

Second, indoor lightning protection: close doors and windows, stay away from walls, pipes and metal objects, live in the center of the room, and do not touch the ground or floor barefoot; Turn off all electrical appliances and make wired calls.

Outdoor lightning protection: stay away from tall buildings, hilltops, trees, iron towers, etc. Choose a dry and low place, squat with your feet together, and don't touch the ground barefoot; Throw away metal objects (keys, mobile phones, knives, etc.). ) you carry it with you; Can't answer the wireless phone.

3, to carry out lightning protection safety knowledge education, improve teachers and students' understanding of lightning protection safety and protection ability.

Fourth, the emergency measures taken by the school

1. Strengthen the publicity and education on safety precautions, improve the safety awareness of teachers and students in the whole school, and educate teachers and students on safety precautions and emergency rescue through one-day activities and class meetings by various forms and means.

2. When the rainstorm comes, the school security administrator should quickly cut off the main power supply of the campus.

3. In outdoor activities, teachers should immediately organize students to quickly hide in buildings protected by lightning protection facilities.

4. In the event of lightning, teachers should calm students' emotions, calmly observe the surrounding environment and quickly take countermeasures, so that students can squat down with their legs together, their heads on their knees and their hands clasped, and they cannot kneel or lie down.

5, in case of major problems, in a timely manner at the same time, timely report to the higher education authorities.

6, conscientiously do a good job in campus circuit, equipment safety hidden trouble investigation.

;