Traditional Culture Encyclopedia - Weather forecast - What should I do if I forget to sew beautifully?

What should I do if I forget to sew beautifully?

What should I do if I forget to sew beautifully?

What if I forget to press the seam when sewing? Many people will do it at home, but sewing is a technical job. Obviously, sewing is easy to fail if you are not skilled. Even professional sewing masters make mistakes. What should I do if I forget to press the seam when sharing sewing?

What if I forget to press the seam when sewing? 1 How long can it take to press the seam after the seam agent is bonded?

The drying time of the suture agent is about 2-3 hours, depending on the temperature conditions. The temperature is relatively high in summer, so the sewing agent should be pressed immediately after sewing. If the temperature is high, try to control it within 10 minute. Tips on sewing time after gluing with beautiful sewing agent for two seasons in Xia Dong:

In summer, the weather is hot and the temperature is high. If it is sewn by one person, be sure to pay attention to sewing a few seams and then press it immediately. Don't try to crush these sewing workers after you finish. This mending agent will cure quickly at high temperature. Wait until you finish sewing a set of beautiful sewing agent, which is in the process of curing. When you go to sew, you will find that you can't sew at all. The beautiful sewing agent has hardened and cannot be pressed.

It is best for two people to cooperate in sewing construction in Xia Tianmei. One person is in charge of sewing, and the other is in charge of sewing. The person in front is as responsible for sewing as the person behind. After the sewing agent is pumped out, you should finish sewing quickly. You can't wait, and you don't need to wait.

It is better to sew when the temperature is low in winter, and the curing time of the sewing agent is much longer when the temperature is low. If a person is doing joint construction, you can wait until a group of joint agents is finished before pressing joint. If you apply the sewing agent yourself and press the seam yourself, you can apply more sewing agent before pressing the seam, which will improve the work efficiency.

What should I do if I forget to press the seam when the sewing agent is dry?

There is only one way. When the sealant dries, forget to press the seam, that is, shovel it off with a scraper and then reapply the sealant. However, if it is not easy to remove, and you are afraid that the shovel will scratch the tiles, you can use the following methods to remove the sealant:

1, put hydrochloric acid: If the tile seam is not smooth when it is beautiful, and now it is dry, we can all put some hydrochloric acid, then treat this caulking agent and do it again. If you don't handle it, this sealant can't be smoothed out any more. Therefore, putting hydrochloric acid should be a better method, but the proportion must be clear.

2. Use vinegar: If you want to smooth the sewing agent again, you need to remove each piece of land first, and then do it again. In this case, the effect is better. Then we can use our vinegar to wipe on the sewing workers. It can usually be removed after a period of time, because the acidity in vinegar can corrode. So this is also a better method.

3. Alcohol toothpaste: If the tile sealant is used for a long time and it is difficult to clean when it is dry, then if you have time, you can use toothpaste and alcohol. Try to remove it, but be careful when using it. Because if you are not careful, you may scratch the surface of the tile, so you must be careful when you do it. In this case, the tiles will not be replaced, otherwise the cups that cost a lot of money will be particularly troublesome.

What if I forget to press the seam when sewing? 2 how to repair the sewing agent if it is not ready?

The sewing agent is not ready, maybe it was not pressed in place when sewing. Because the construction requirements of caulking agent and jointing agent are different, the technical requirements will be stricter. If the technology is not up to standard, the sewing agent made at this time is not very good. We need to fix the sealant first, then clean the sealant on the tile with tools, and then re-paste the tile. But when using sewing tools, you must choose the matching sewing tools. In this way, beautiful sewing will be done better after sewing.

If you don't sew for a long time, it will blister, deform or whiten. This phenomenon may be cut corners during the construction, and then directly put a layer of glue on the outside. This is not effective, so we have to make a second remedy. Clean up the sealant in the gap first, and then repaint the sealant.

Moreover, when sewing beautifully, many people will forget to sew or choose the wrong sewing tool after applying glue, so the sewing effect is not very good. If you forget to press the seam, you should press the seam with a tool immediately before the glue is completely dry. If the wrong tool is used, it should be compacted with the right tool before the glue is completely dry.

When sewing, it is best to let experienced people operate it. And we should operate step by step in strict accordance with the prescribed requirements. After this operation is completed, the beautiful seam will be made more beautiful. If it is not done well, it must be adjusted immediately, and it is not particularly difficult to adjust the seam after curing.

What should I do if I forget to press the seam? Can I make another layer on the original seam?

There may be some mistakes in the construction of the beautiful seam, which leads to the failure of the beautiful seam. Some friends want to make another layer on the original seam, depending on the situation. If there is not enough colloid in the seam, it can only be found by pressing the seam. This situation can be remedied by applying glue water directly on it. Or if you don't like the sewing effect, you can clean the surface after the sewing agent is cured, then apply a layer of glue on it again and sew with a bigger tool.

How to remedy the mistakes in sewing?

If the construction is wrong, it must be made up in time, and the remedy method needs to be decided according to different situations.

1. The sewing agent swells, turns white and does not dry.

Some owners want to stick another layer of glue to remedy it. In this case, direct remedy is impossible. It is necessary to shovel out all the sealant in the gap, find out the cause of the problem, then clean the gap and re-glue it. Otherwise, it will easily affect the quality and effect of joint filling, because the hardness of joint filling agent is high after curing. It is suggested to soften it with a hair dryer first, and then remove the joint filling agent to avoid damaging the tiles.

2. I forgot to press the seam

The sewing step is very important. Many owners will forget to press the seam when they are doing beautiful sewing, and they will remember it when they want to shovel glue. At this point, the sealant has solidified. Don't think that shoveling is enough. You can't shovel glue directly without pressing seams. If the forgetting time is not long and the sealant has not solidified, it can be pressed. If it has solidified, it needs to be shoveled and rebuilt.

3. Insufficient colloid in the gap

When gluing, the moving speed is too fast, resulting in insufficient colloid in the gap, which is only found when pressing the seam. This situation can be remedied by applying glue water directly on it.

I don't like the sewing effect.

Different from the caulking agent, the caulking will have a certain radian, but the specifications of the caulking tool are not suitable, and the owner may not like the extrusion effect. You can clean the surface after the sealant is cured, and then apply a layer of glue on it again and press the joint with a larger tool.

How to sew again;

First of all, shovel out the original sewing agent in the gap. If it has solidified, we can use an industrial hot air gun to blow the sewing agent soft, and then use a shovel. Find out the cause of the problem of the beautiful seam, clean the gap, and then re-glue the construction to avoid the previous mistakes.