How to solve the problem of excessive gaps in pure wooden floors

The widening of the floor gap may be due to the fact that the moisture content of the floor was high when it was first installed, and then slowly shrank, causing the gap to increase. It may also be because the house has been unoccupied for a long time and is airtight. The humidity in the rainy season is heavy, and the floor swells and warps. After repairs, the gaps in some places are too large. Whether repairs are needed can be done by checking whether there are any traces on the baseboards on the wall.

When encountering this situation, the householder can observe it for a period of time. When the crack is four to five millimeters thick and mud and dust accumulate, he can buy "bakelite powder" and scoop it up in a dish, drop it into clean water and stir until it Then brush out the cracks, spray a little water, and fill in the bakelite powder slurry. Bakelite slurry usually dries and hardens overnight, and the wooden floor can be stepped on as usual.

There are two ways to repair cracks and holes on the board surface: one is to cut old books and newspapers into pieces, add an appropriate amount of alum, boil it with water to make a paste, and embed it in the cracks. It will be very strong after drying. The second is to mix white glue with sawdust and mix evenly, embed it into the crack, and polish it with sandpaper after a day and night. It is simple and economical.

Floor maintenance:

1. Laminated wood flooring

Laminated wood flooring maintenance is much simpler than solid wood flooring. When cleaning the floor, pay attention to keeping the floor dry, do not wash it with a large amount of water, and be careful to avoid local immersion of the floor in water for a long time. When cleaning stains, use neutral detergent and avoid direct sunlight, rain, moisture, etc. In addition, paying attention to indoor ventilation and maintaining indoor temperature will also help extend the life of the floor. Laminate flooring does not require painting or waxing. Unlike solid wood flooring, sandpaper should not be used to polish it.

2. Solid wood flooring

Improper installation and use of solid wood flooring will cause quality problems in qualified products. When maintaining solid wood floors, pay attention to dryness and cleanliness of the ground. When laying solid wood floors, if there is no moisture-proof treatment and the bathroom and room floors are not isolated, the life of the floor will be affected. Being wet with water or scrubbed with alkaline water or soapy water will destroy the brightness of the paint. If you fail to close the curtains in the summer, the floor in front of the bed will become discolored and crack after being exposed to the sun. If the air conditioner temperature is turned on too low, the temperature changes between day and night will be too large, causing the floor to expand or contract too much, resulting in deformation and cracking of the floor.

During the use of the floor, if it is found that some floors are crusted or peeled off, the floor should be picked up in time, the old glue and dust should be shoveled off, and new glue should be applied and compacted. Waxing once a month is also the best maintenance method, but you should wipe away moisture and stains before waxing.

3. Solid wood composite flooring

The maintenance of solid wood composite flooring is simpler than that of solid wood flooring. Keeping the floor dry and clean, mopping the floor without dripping mops, wiping with alkaline water or soapy water can effectively protect the floor.

If the air in your home is dry, you can moisten the mop or put a basin of water on the heater. You can also use a humidifier to moisten it. Try to avoid sunlight exposure to prevent the surface paint from aging and cracking under long-term exposure to ultraviolet rays. If the local board surface is accidentally stained with stains, it should be removed in time. If there is oil stain, you can use a rag dipped in warm water and a small amount of washing powder to scrub it. If it is a drug or paint, it must be removed before the stain penetrates the wood surface.

High-temperature floors in summer also need to "resume the heat"

In hot weather, the most common problem with floors is shrinkage and seams, because at high temperatures, moisture inside the wood can easily The volatilization causes the volume of the floor to shrink, which leads to the widening of the gaps at the floor joints, and in severe cases, tongue and groove detachment, cracking, etc.

Enclosed space and continuous high temperature are the main culprits of wooden floor seams. The renovated new home has been left unattended for a long time, and the interior is sealed and airtight, causing the indoor temperature to be very high. The house is no different from a drying kiln. Under such conditions, the moisture contained in the floor continues to evaporate, and severe shrinkage and joint separation are of course inevitable.

In addition, wooden floors are also afraid of being exposed to the scorching sun. Many floor seams occur near balconies or windows. Exposure to the sun may also cause the paint film to bubble, discolor, or even peel off. Wood still has some living characteristics after it's been cut, so you should treat your floors with care and thoughtfulness.

The residence with wooden floors must be occupied by someone. If it is really not possible to move in immediately, ventilation and heat dissipation must be maintained regularly. Try not to blow the air conditioner on the floor. If the room feels dry, you can humidify it appropriately. When going out, you should close the curtains to avoid direct sunlight on the floor.