On rainy days, there is water all over the house.

On rainy days, there is water all over the house.

On rainy days, there is water all over the ground. Many people will find that there is a lot of water on the floor at home when it rains. When the home construction is not standardized or the materials are not selected properly, there will be many headaches in the later period. Let's share that there is water on the floor in rainy days.

There is water everywhere in the house on rainy days 1, which is related to the season. Especially in our south, when it rains, tiles are particularly easy to regain moisture. Rainy weather, the temperature is relatively high, so the humidity is relatively high, and it is easy to produce water droplets. However, this phenomenon will disappear when the weather improves.

Regarding the ground treatment, the waterproof treatment of the foundation was not done well when the tiles were laid, or the purchased tiles did not absorb water, which led to the formation of water vapor in the underground soil. The tiles are wet, which leads to high humidity in the room. This situation is troublesome to deal with, and it is necessary to deal with the waterproof problem of foundation again.

The ventilation effect is not good, and there is water leakage in the room, which leads to the resurgence of tiles.

Solution:

Dehumidify with air conditioner. Most air conditioners now have this function. Turning on the dehumidification function of air conditioner can effectively solve the indoor humidity problem in rainy days, and can also form all-round protection for "moisture-proof" household appliances such as TV sets and computers.

If the outside air humidity is too high, remember to close the doors and windows; If the room is too humid, make sure the room is ventilated and dehumidified with air conditioner and fan.

Put some quicklime (mixed with some sand) in the wet corner.

On rainy days, there is water all over the house. On rainy days, there is no way to get wet at home. This may be because:

Reason: After the door and window seal fails or the high-quality sealing material is not installed, the gap width between the door and window pulley and the overhead track can reach more than 8 mm at the widest part of the upper and lower track grooves (not easy to see). The strong wind in the heavy rain makes the rain enter the room through these gaps with the wind.

Solution: Find a nearby door, window and screen processing and maintenance master to help install the fully hidden sealing material (automotive grade) for the windows. Strong hands-on ability can also seal the gaps in five directions of doors and windows by themselves (invisible installation does not affect push-pull and switch).

What should I do if there is water on the ground at home when it rains?

1, moistureproof treatment. After the local treatment of cracks and hollows, the surface layer should be fully moisture-proof and closed. The principle of treatment is to block the capillary permeation channel in cement mortar or concrete. Generally, the method of brushing waterproof paint or waterproof agent can be adopted.

Before painting, the surface should be scraped and cleaned, and two waterproof coatings should be painted. When brushing the road, force it to penetrate into the capillary hole. After the coating is dried (generally about 24 hours), brush it for the second time to form an integral waterproof coating. At the corner between the ground and the wall, paint should be brushed to the height of the wall skirting board.

Check. First, check whether there are cracks on the ground, which is the main channel for groundwater to penetrate upwards. Generally, cracks with a width exceeding 0.05 mm are visible cracks on cement mortar or monolithic concrete floor.

Regular cracks usually appear along the longitudinal or transverse direction of the room, which is formed by shrinkage and cracking of materials. Check the ground again for empty drums. You can tap vertically along the ground with a wooden stick. If the tapping is free, then there is an empty drum.

3, cracks, empty drum processing. For regular cracks, V-shaped cracks should be chiseled. After the cracks are cleaned, they should be sealed with asphalt ointment. If it can be baked with flame, the cracks can be fully dried.

Generally, hair cracks are closed in a large area. Where there is an empty drum, the surface layer should be knocked off, the cushion layer should be chiseled off, a cement slurry should be brushed on the cushion layer, and then the surface layer should be repaired and leveled with the same material.

4, the original ground moistureproof treatment, do a new surface. The choice of new surface material should consider the high strength, wear resistance, moisture-proof ability, easy cleaning, practical and beautiful, and cement mortar surface can also be used.

As for air humidity, except for special needs, equipment can be used to control humidity. Generally, buildings should not open windward windows and doors, so as to reduce the influx of humid air into the room.

Why is the tile floor wet?

Indoor humidity mainly occurs on the ground floor of the house. There are generally two reasons:

First, when humid air with high temperature (relative humidity above 90%) meets the ground with low temperature, the ground is smooth and does not absorb water, and it is easy to produce condensed water on the ground (usually it will be produced when the temperature is around 2℃). This happens mostly in the rainy season, with much rain, high temperature and high humidity. Once the climate turns sunny and dry, the humidity phenomenon can be eliminated;

Second, the water in the foundation soil under the ground cushion rises by capillary action, and the vaporous water permeates upward, which makes the ground material wet and aggravates the humidity deterioration of the whole room. This kind of situation often happens all the year round and is difficult to deal with.

In addition, there are reasons such as poor outdoor drainage and poor indoor ventilation. The surface layer in most parts of South China is mostly clay and loam. Capillary water level of clay can rise to 2-2.5m, and loam can reach1-1.3m.. When building materials with poor compactness are used as indoor floors, the capillary action will be enhanced, and the ground moisture will be more serious.

On rainy days, there is water all over the house. 3. What should I do if the floor tiles in my living room suddenly seep?

First of all, check the causes of water seepage in floor tiles. If the weather is wet, you should open the window to ventilate. If the water pipe leaks, find the cause of the rupture and replace it with a new one.

If there is water seepage in the gap of ceramic tile, it should be filled with waterproof caulking agent at this time. If there is a fault in the waterproof layer, a new waterproof layer should be made at this time. Knock off the floor first, then waterproof and lay the floor.

Second, how to deal with the leakage of floor tile joints?

If there is a problem with the waterproof layer, take the tiles apart first, and then blow the putty when you see the inner wall. Then the wall is waterproof and tiled. This method is particularly complicated, so be sure to check it clearly before operation.

If the joint of the floor tile leaks, it is caused by the rupture of the water pipe. At this time, the water pipe should be tested first to see if there is any water leakage.

If it is really the phenomenon caused by the broken water pipe, it is necessary to check the leaking place first, then cut the wall open and replace it with a new water pipe. If the cracks in ceramic tiles are not handled properly, water seepage will occur. At this time, the gap should be filled with special cement and caulking agent, and then the waterproof layer should be made.

Or fill the tiles with waterproof caulking agent. If there is water seepage inside the cracks in the tiles, then use waterproof caulking agent to fill the cracks in the tiles. Moreover, the water permeability of the tile itself is particularly low, so there is often water seepage in the cracks of the tile, and then the water leakage phenomenon can be solved in place.

If you haven't been waterproof before, you should be waterproof again at this time. Cracks in ceramic tiles will appear if they expand with heat and contract with cold, so the main solution is to make waterproof layer again.