Installation steps of quick-loading wallboard Advantages analysis of quick-loading wallboard

Quick-assembled wallboard is a new type of environmental protection decorative material, which has been loved by consumers because of its functions of environmental protection, moisture prevention and heat preservation. However, when choosing to decorate, we don't know how to decorate. Everyone who knows how to install it feels particularly simple, but we don't know how to start. Let's take a look at the installation steps and advantages of quick-loading wallboard with everyone!

Advantages of fast loading wallboard

1. Thermal insulation

Tested by the national authoritative department, the thermal insulation efficiency exceeds the existing national standards, and the temperature difference between the installation room and the ordinary plate installation room is 7 degrees; Compared with paint, the phase difference is 10 degree, which is the best material for wall decoration in hot summer and cold winter areas in south China. This product has unique thermal insulation performance. When it is applied to balconies, sun rooms and villas, it completely solves the problem of sun exposure on the top floor. It achieves obvious energy-saving effect and is also an energy-saving decorative material strongly advocated by the state.

2. Sound insulation

Tested by national authorities, the sound insulation reaches 29 decibels, which is equivalent to the sound insulation of solid walls. If it is used in the bathroom, it can obviously solve the underwater sound of sewer pipes, and can also be applied to various sound insulation rooms in factories.

3. Fire prevention

Tested by the national authority, the fire protection grade reaches B 1, which basically meets the fire protection requirements of the project.

4. Super hardness

The product is made of aluminum alloy plate and polyurethane, which increases the strength and hardness of the product and can be used for various retaining walls.

5. Waterproof and moistureproof

The product has moisture-proof performance, which is especially suitable for decoration in the south, and especially solves the problem of decoration mildew caused by wall leakage in the decoration of southern families.

6. Green and environmental protection

The raw materials used on the surface of the product are all environmentally friendly materials, and the installed room is environmentally friendly and tasteless. If the room is decorated as a whole, there will be no painting process, which solves the problems of decoration material time and paint smell. If you install it today and move in tomorrow, it will save time.

7. Easy to install

The traditional gusset plate installation method is adopted in product design, which greatly solves the complicated installation of other aluminum plates and can be directly installed on the blank wall without professionals and ordinary carpenters, saving labor, time and space.

Installation steps:

Prepare materials

Art cutter, desktop cutting machine (choose serrated saw blade with higher rotating speed), grinder (serrated saw blade), square ruler, tape measure, triangular file, curve saw, 3P air pump, air gun, cement nail gun, wood square: mainly used for structural parts of top light return belt. Wood board: mainly used for background wall. Corner line: Some corners are closed.

Installation measurement calculation

It is estimated that the wall area is commonly used in home improvement, which is three times of the floor area, basically including the wall and the roof. The basic installation area is in this area. Accounting method for measuring the actual area by household: according to the measured area, basically ensure that the height from the top to the ground is not less than 2.75M after the optical loop is completed, and try to ensure the unnecessary losses of consumers during the installation process after accounting.

Material preparation calculation

Make sure that two pieces of material are prepared on the same wall. The background wall needs to be spliced, and a large number of places should be prepared to be more than 0.5 square meters.

construction sequence

The wood structure of the top reflective belt and background wall should be made of wood according to the design requirements, and attention should be paid to the matters needing attention in the operation. There are enough points in the wood structure for fixing the quick-loading wall; Ensure the straightness of the wood square edge; Try to make both sides of the right angle equal in size; The structure is relatively firm; After the wood structure is completed, the actual wiring is carried out and the electrical connection ports are reserved. Water pipe layout and floor installation. Top-mounted quick-loading wall surface, generally, the quick-loading wall surface is installed from the top during the installation process. In the process of cutting plates, it is necessary to make the material section straight and burr-free. The higher the speed of the cutting saw, the less burrs there are. The measurement error must be within 2MM, otherwise the flat-fell seam will be extremely untidy. Wall and background wall installation, in this installation process, such as the use of internal corner line, foot line, waist line, door cover line, window cover line, etc. , line installation line, installed on the fast wall.

Installation processing details

Right-angle bending, in the process of bending, the wall thickness must be included in the bending line (for example, the column is bent at a right angle, the first piece of material is 5CM away from the right angle, the bending line is in the protruding part, the bending line should be 5.8CM, and so on. ) pay attention to the bending process, draw the bending line first, and then take polyurethane material, usually around 8 mm, and bend as straight as possible. 45-degree splicing of concave-convex plates: After the plates are cut at 45 degrees, the burrs are ground flat and then spliced.

Pay attention to right-angle splicing, concave-convex plate right-angle splicing: the inner side of the splicing plate is polished to a 45-degree angle for splicing, and the splicing plate is directly inserted into the notch of another plate. Pay attention to angle control when grinding. Inner corner splicing of concave-convex plate: the outer side of splicing plate is polished to a 45-degree angle for splicing, and the splicing plate is directly inserted into the notch of another plate. Pay attention to angle control when grinding, and its principle is the same as right-angle splicing.

acceptance standard

Flat seams are neat; The closed position does not affect the appearance at all; The material is firmly fixed, and there is no hole in the attached wall material; Reasonable color matching; The internal insulation layer has no external leakage; Corrugated plate butt joint is complete without burr; Whether the folds are at right angles, smooth and beautiful.

When we choose to install quick-loading wallboard, we need to know its advantages and disadvantages and installation steps. Then go and buy it. The above are the advantages and installation steps of the quick-loading wallboard introduced by Bian Xiao, which ends here.