How to polish hotel marble?

Many people like to install marble when decorating. It looks very beautiful. However, with the passage of time, people's use and improper artificial care in the process can easily make marble lose its original luster and brightness. Some people say that it is not good to change it, but the cost is too high and the time is too long, which may delay the normal use. Therefore, many people will choose polishing, polishing and polishing on the original basis to restore its original luster and brightness. So, how to polish marble? How to maintain after polishing?

How to polish marble?

1. Thoroughly clean the floor. First, use a cutter to remove the concrete slurry at the crack of the stone, and then use a brush and vacuum cleaner to thoroughly remove the dust. Wipe it with a clean mop, and the ground is free of sand and impurities.

2. After the overall cleaning of the stone surface is completed, repair the small broken points and crevices on each stone with marble glue. First, repair the original damaged surface with marble glue close to the color of stone. Then, use a special stone slitting machine to slit the middle seam of the original stone installation neatly again to make the seam width uniform, and then fill it with marble glue close to the color of stone. After the marble glue is mended, you must wait for the glue to dry before you can do the next process.

3. After the marble glue dries, grind the whole ground with a grinder, and grind it horizontally as a whole, focusing on grinding the caulking glue between the stone and the edge near the wall, decorative modeling and special-shaped modeling, keeping the whole stone ground flat, completing the first grinding, caulking the marble glue again, and grinding it for the second time after caulking, and then using a stone refurbished machine to match the steel stone water mill from coarse to fine. * * It needs to be completed seven times. (Bridge grinding and professional grinding must be used for granite renovation, and resin grinding is not allowed. Rough grinding: it is not allowed to reduce grinding times and change the number of grinding discs. Use a 60-mesh grinding plate to polish the stone floor. The colors of cutting, height difference, scratches and deformation are basically the same, and it must be full. Fine grinding: Do not reduce the grinding times, and do not change the mesh of the grinding plate. )

4. After polishing, treat the water on the ground with water absorbent, and blow dry the whole stone floor with a hair dryer. If time permits, natural air drying can also be used to keep the stone surface dry.

5. Spray the liquid medicine evenly on the ground, polish it with a marble polishing machine, and sprinkle the liquid medicine and the same amount of water on the ground with a cleaning machine with a red cleaning pad to start polishing. Under the action of thermal energy, the surface effect formed by the crystallization of crystal surface substances on the stone surface.

6. Overall ground maintenance treatment: if the stone with large porosity is coated with marble protectant, it should be re-polished to increase the crystal face hardness of the overall ground.

7. Ground cleaning and maintenance: When a crystal mirror is formed on the stone surface, use a vacuum cleaner to absorb the residue and moisture on the ground, and finally use a polishing pad to polish it, so that the whole ground is completely dry and bright as a mirror. If it is damaged locally, it can be repaired locally, and you can walk on it at any time after the construction is completed. (After the stone surface is dried, do crystallization hardening treatment until the surface effect required by the sample is achieved. After the transformation, the mirror gloss of the cave stone surface reaches more than 60 degrees, and there can be no height difference between stones. Granite surface reaches above 80 degrees, and there can be no glue leakage. )

How to maintain marble after polishing

1. After the continuous care of the crystal layer and crystal layer polished by the marble grinding block (commonly known as crystal face care), the pores are not completely closed, the marble can still breathe inside and outside, and the stone is not easy to get sick. At the same time, it has certain waterproof and antifouling effects.

2. After the marble is waxed and polished, the pores of the stone are completely closed, and the stone can't breathe inside and outside, and the stone is prone to pathological changes.

3. The continuous nursing operation of the polished crystal layer and the crystal layer of the marble grinding block is simple, and it is not necessary to clean the ground with a cleaning agent, and it can be polished directly with clear water and dried with chemicals. Can be polished and cared at any time and can be operated locally. There is no new contrast in the surface color of marble.

4. After waxing and polishing marble, after a period of time, it is necessary to remove the worn wax layer and use waxing water. Large-scale simultaneous operation and construction are required, and local construction is not allowed. After local construction, the surface will have color difference.

The above content is Bian Xiao's concrete introduction to "How to polish marble and how to maintain it after polishing". The surface of marble looks smooth, but it has gone through many processes to become so beautiful. Besides being beautiful, it can also play an anti-slip role. Marble polishing is a very important process, so we should pay more attention to it during operation and do a good job of maintenance after installation to prolong its service life.