Introduction of how to fix the stainless steel skirting line

Stainless steel skirting is a special kind of skirting material at present. Compared with traditional wooden skirting, stainless steel skirting is more beautiful, firm, green and environmentally friendly. Stainless steel skirting is not only suitable for home decoration, but also suitable for hotels, hotels, office buildings and various public places. So how to fix stainless steel skirting? Let me take you to know about Home Network No.1 below.

in the home with modernist decoration style, simple and textured decoration materials are the first choice. The use of stainless steel skirting can make the overall style more fashionable, and show different texture and quality in details. Let's learn the fixing method of stainless steel skirting together.

stainless steel skirting line fixing method:

1. Preparation

1. Making positioning ruler: When installing the buckle, use the positioning ruler to determine the height of the buckle installation position. The positioning ruler is 1-24 mm long; 4-5 mm wide; The height depends on the model of the baseboard, and the height of T7 is 17-17.5 mm; T8 is 14.5-15mm high; T1 is 38-38.5mm high; The height of T11 is 36.5-37mm; The positioning ruler can be made of wood or iron.

2. Cleaning the wall foundation: remove the cement floating blocks protruding from the wall, corner and wall root where the skirting line is installed; Check the flatness of the wall, and the maximum gap is not more than 3mm. No side, the convex part of the wall should be leveled. The recess of the wall should be padded.

2. Install the buckle

1. Installation method 1 (cement nail fixing): put the buckle on the positioning ruler, lean against the wall, press the upper end of the buckle with your fingers and fix it with a nail gun, as shown in Figure 1. The cement nail row is 32 mm long; The spacing between buckles is about 4 mm; There should be a buckle at the interface of two skirting lines; There should be a buckle at the end of the wall about 3 mm.

2. installation method 2 (punching and fixing with impact drill): fix a drilling jig on the positioning ruler (the diameter of the drilling jig hole is slightly larger than that of the impact drill), press against the wall root, and drill holes into the wall with the impact drill; Drive a wooden needle or plastic expansion tube into the hole. When fixing the buckle, it is still necessary to use the positioning ruler to adjust the buckle and fix it at the same height (using the waist hole on the buckle). The rest is the same as above

3. Note: the wooden wall or plasterboard wall should be fixed with a carpenter's nail gun; Gypsum wall can also use light steel keel to fix the buckle with self-tapping screws.

3. Installation of skirting profile

1. After ensuring that all buckles have been installed on the same straight line (with an error of 1.5 mm), cut the corners of yin and yang according to the size (leaving a seam of about 2 mm for the joint of silicone cement) and grind off burrs. Then tear off the protective film on the bottom of the skirting line to seal it with silicone rubber. Neutral silicone rubber for sealing and mortar joint is usually silver gray or white in color.

2. hang the upper groove of the skirting line with a good size on the upper opening of the buckle, then lift the rear end of the skirting line up a little and press it down against the wall, so that the upper convex card of the buckle completely enters the upper groove of the skirting line, and pat the middle of the skirting line at the same time, as shown in Figure 2. When installing, start from one end, press one clip at a time to the other end gradually, and avoid hammering.

3. After installation, the gap between the skirting line and the wall and the ground shall be sealed with silicone rubber, and the reserved 2mm gap between the yin and yang corners and the flat joint shall be bonded with masking paper and then bonded with silicone cement.

4. Tear off all the protective films on the skirting line, wipe off the residual glue on the stainless steel veneer with old powder, and remove the black spots formed by the glue heating at the incision with wire drawing cloth.

5. It is easier to install by using stainless steel internal and external corners, and customers are welcome to choose. Its installation method: after the skirting line is installed, the internal angle, external angle and head are respectively stuck at the joint with AB glue.

How to fix the stainless steel skirting line is here for you. This stainless steel skirting line is a new material in the decoration market in recent years, and it is still relatively novel in home decoration. Using stainless steel skirting line can add a lot of colors to your home style, but you need to communicate with the designer before making a purchase.