Traditional Culture Encyclopedia - Photography major - How to balance the camera tripod

How to balance the camera tripod

As long as the camera tripod shakes left and right, it will tilt, tilt badly, and then it will be leveled. What should I do?

The tripod is fixed and generally flat. Adjust the pan/tilt to control the level. If the tripod is fixed and can shake, it is not fixed. If the shelf itself can shake, exchange goods and return them.

How to level the camera when it is broken?

How to level the level: _

(1) Flat terrain: First, loosen the tripod fixing screws, and stretch the tripod close to yourself. The length of the tripod should not exceed the tip of your nose, and then fix the screws. Place the three tripods of the tripod between two observation points, open the instrument box after the tripod is roughly in line with the ground, and install the sighting part of the level on the tripod with connecting screws. _ The second step is to look at the position of the bubble in the circular level (pay attention to rotate the triangular spiral of the sighting part of the level roughly to the middle before installation). The direction of the round medicine bottle indicates that the direction is high. At this time, just hold one of the tripods (the other two are stationary) and move back and forth until the round bottle is basically in the center of the round bottle or in the circle of the round bottle. Finally, it is accurate leveling.

(2) Uneven terrain (steep slope): First, adjust the length of the three legs according to the terrain. If the slope is steep, you can let two long legs down and one short leg up. Similarly, make the level level roughly horizontal by visual inspection (then step on any two feet, leaving one movable for easy adjustment), or lift the tripod to make the air bubble roughly centered, and then level it with foot screws. _ Note: If the ground is soft, all three legs should be stamped firmly, and then rough and fine leveling should be carried out.

How to adjust the tripod? How to mount the camera on a tripod?

1. The first step to open the tripod is to open the buckle below, as shown in the figure below.

2. For the camera, it is to install the turnbuckle at the bottom. The belt buckle must be tightened, as shown in the figure below.

3. After straightening the tripod, we first screw this bolt to the right to increase the spacing in the slot, as shown in the figure below.

4. Install the button in the red box at the bottom of the card slot, carefully aim the camera at the snap screw, and slowly move forward, as shown in the figure below.

5. When the camera is pushed to the deepest position, tighten the limit bolt again, so that the camera is only stuck in the card slot, as shown in the figure below.

6. Tighten the bolts here again to prevent the camera from shaking up and down to ensure safety, as shown in the figure below.

7. Adjust the big bolt at the bottom to the overall level, and complete all installation and adjustment, as shown in the figure below.

Extended data:

Classification of tripods

Tripod can be divided into wood, high-strength plastic, alloy, steel, volcanic rock, carbon fiber and so on. The most common material is aluminum alloy, and the advantages of aluminum alloy tripod are light weight and firmness. The latest tripod is made of carbon fiber, which has better toughness and lighter weight than aluminum alloy.

According to the largest diameter of the big foot pipe, it is divided into 32mm, 28mm, 25mm and 22 mm. Generally speaking, the larger the foot tube, the greater the load-bearing capacity and the stronger the stability of the tripod.

According to the number of foot tube sections, it can be divided into 3 sections, 4 sections and 5 sections. Generally speaking, the fewer the number of foot tube joints, the better the stability of the tripod. On the other hand, the fewer the number of foot tube segments, the less portable they are.

According to the use, it can be divided into tripod for product shooting, tripod for portrait shooting, tripod for landscape shooting, tripod for selfie, etc.

How to adjust the horizontal angle of the tripod of the camera? I found the camera slightly tilted, a few degrees to the left. How to flatten? I tried every one.

Generally, tripods have grades. If there is no other way to adjust the tripod head, you can adjust it through the legs of the tripod. Nowadays, cameras basically have their own level. You can ensure the level of the camera by observing the level and adjusting the three brackets.