Traditional Culture Encyclopedia - Travel guide - Various ways to tie your shoelaces

Various ways to tie your shoelaces

1. Take two shoelaces of different colors, each of which is slightly shorter than the original shoelaces.

2. Thread a shoelace (blue in the legend) from the bottom and out from the bottom of the shoe hole;

3. After crossing, skip a row of shoe holes and pass through the third row of shoe holes from top to bottom.

4. Continue to cross and wear two rows of shoes upward at the same time, until you wear the shoe hole in the uppermost or uppermost second row;

5. Use the second shoelace (yellow in the picture), starting from the second row at the bottom, and repeat the steps from the second part to the fourth part until the second shoelace passes through the remaining shoe hole.

Evaluation: the decorative creativity of machine guns needs extra shoelaces;

Grid system method: edit this paragraph back to the directory.

Lattice system method of shoelace system diagram

1. Insert the toe cap directly from the bottom (gray part) and go out from the bottom of each shoe hole.

2. Skip two rows of shoe holes and enter the fourth row of shoe holes after passing through.

3. Then, the two ends of the shoelace vertically jump off a row of shoe holes and pass through the second row of shoe holes;

4. Repeat the second and third steps, insert into the fifth row of shoe holes, and then exit downward from the third row of shoe holes;

5. After passing through, pass through the uppermost shoe hole.

Evaluation: The leftover shoelaces used for decoration are short and not easy to fasten, which is only suitable for shoes with 6 pairs of holes;

Context method: Edit this paragraph back to the directory.

Upper and lower tying method of shoelace tying diagram

1. Thread the toe cap directly from the bottom (gray part) and out from the top of each shoe hole.

2. The toe cap passes through the bottom, through the second pair of shoe holes from bottom to top, then through the top, and then inserted into the third pair of shoe holes.

3. Repeat this process, only let the shoelaces pass through the upper two shoe holes;

Evaluation: convenient decoration, less wear.

Rope ladder method: edit this paragraph back to the directory.

Rope ladder method for shoelace diagram

1. Insert the toe cap from the bottom (gray part) through the two bottom holes;

2. Both ends of shoelaces are aligned upwards and pass through the second row of shoe holes.

3. Before threading the shoelaces upward into the next row of holes, cross-thread the shoelaces under the shoelaces on the other side in the vertical direction.

4. In the top hole, two shoelaces cross under the vertical part, and then fasten them.

Evaluation: neatness and decoration are short, and it is difficult to fasten the toe.

One-handed method: Edit this paragraph back to the directory.

One-handed lacing diagram

1. Take a shoelace slightly shorter than the normal shoelace and tie it at one end.

2. Pass the untwisted end through the rightmost shoe hole, and pull it to the knotted position to be blocked by the shoe hole.

3. Wear the shoelaces zigzag through the shoe store.

4. The loose end (blue) can be easily tucked under the shoelace to prevent looseness.

Evaluation: Super simple, convenient for the disabled to relax.

Zip method: edit this paragraph back to the table of contents.

Schematic diagram of shoelace chain method

1. Insert the toe cap directly from the bottom (gray part) and go out from the bottom of each shoe hole.

2. The toe cap is rounded on the back of the upper.

3. The two toe caps cross each other, and then go out from below to the next row of shoe holes.

4. Repeat this process until both heads are inserted into the uppermost shoe hole.

The decorative evaluation is very strong and it is difficult to fasten;

Shoe store system method: edit this paragraph and return to the catalog.

Take shoelace tying method as an example to explain the tying method of shoes.

1. Thread the toe strap from the bottom (gray part) directly into the two shoe holes at the bottom.

2. The two side ends (blue ends) of the shoelace are pulled obliquely to the uppermost shoe hole on the right side and passed out.

3. The right end of the forehead (yellow end) zigzags through the remaining shoe holes.

Evaluation: Lazy tying method reduces the remaining length of shoelaces and adjusts the length of shoelaces.

Sawtooth system: edit this paragraph and return to the directory.

Sawtooth tying method of shoelace tying diagram

1. Thread the bottom (gray part) of the toe strap directly into the two shoe holes at the bottom from top to bottom.

2. One end of the shoelace (yellow end) goes straight out along the right side and horizontally passes through the second row of shoe holes.

3. The other end of the shoelace (blue end) jumps over the second row of shoe holes, obliquely penetrates from below, and passes through the third row of shoe holes on the right.

4. Continue to push the two toe caps in pairs upward through the hole until one end (yellow head in the figure) extends from the right side to the top hole.

5. The other end of the shoelace (the yellow end in the figure) goes up along the left side and goes out from the uppermost hole on the left side.

Segmentation method: edit this paragraph and return to the directory.

Sectional fastening method of shoelace fastening diagram

1. Each shoe has two shoelaces, each of which is slightly longer than half of the original shoelaces.

2. First, put the first shoelace straight in from the bottom (gray part), go out from the bottom of two shoe holes, and then cross to the middle of the shoe.

3. Thread the second shoelace through the middle upper shoe hole and wear it to the top of the shoe in the same way.

4. Each "segment" should be knotted according to the specific situation. For example, if the foot surface is narrow, fasten the lower part; If your feet are wide, you can tie them loosely.

Evaluation: Customizable, practical and chaotic;

Two-color system method: edit this paragraph back to the directory.

Two-color tying method of shoelace tying diagram

1. Take two shoelaces of different colors, each of which is slightly longer than the normal shoelaces of shoes.

2, cut the shoelaces in half, be careful not to start from the middle, it should be offset by 2-3 cm.

3. Tie the shorter part of one color (yellow in the legend) with the longer part of another color (blue in the legend), and then trim the knot.

Extra parts. To be on the safe side, you'd better apply some glue. The remaining two sections are made into two-color shoelaces of the other shoe;

4. Pass the long section (blue) through the shoe hole in the lower right corner until it is blocked by the knotted joint.

5, and then according to the direct method (fashion).

Evaluation: it is very decorative and requires a little discomfort.

Bootstrap method: edit this paragraph back to the directory.

Explanation of whip method and shoelace method

1. Obliquely pass through the shoelaces at both ends (gray parts) and respectively pass through the lower left and upper right shoe holes;

2. The upper end of the shoelace (blue) crosses from the top to the middle hole in the shape of "shoelace"

3. The lower end of the shoelace (yellow) zigzags through the middle shoe hole from below by "shoe store tying method".

Evaluation: unique design, beautiful appearance and special use.

Double reverse link method: edit this paragraph back to the table of contents.

Double-back tying method for shoelace tying diagram

1. Thread the shoelaces directly through the holes in the second row above (gray part).

2. Cross the ends of shoelaces, skip the third row of shoe holes and enter the fourth row of shoe holes.

3. Continue downward and pass through two rows of shoe holes at the same time;

4. After passing through the bottom two shoe holes, pass through the spare shoe holes in pairs.

Evaluation: the remaining shoelaces are short and difficult to fasten;

Hash system method: edit this paragraph and return to the directory.

Hash method of shoelace tying diagram

1. Insert the toe cap directly from the bottom (gray part) and go out from the bottom of each shoe hole.

2. Skip two rows of shoe holes and enter the fourth row of shoe holes after passing through.

3. Then the two ends of the shoelace pass vertically downward through the third shoe hole;

4. Continue to wear upward, go up three rows after each crossing, and then come back and wear it out from the next row of shoe holes.

Evaluation: The leftover shoelaces for decoration are short and difficult to tie.

Chessboard system method: edit this paragraph and return to the directory.

Chessboard tying method for shoelace tying diagram

1. Take two pairs of shoelaces with different colors, preferably the flat one.

2. Tie the shoelaces straight (popular) or straight (lazy) with one of the colors (yellow in the legend).

3. Use another color shoelace (blue in the legend) to thread the first shoelace up and down from the bottom until it reaches the top. 、

4. Fold the shoelace at the top, then go down and up until it reaches the bottom.

5. Repeat the third and fourth steps and continue to wear until the gap in the middle is filled or the shoelaces are tied;

6. Put all the shoes that have grown into shoes;

Evaluation: strong decoration, easy to wear, easy to take off and easy to loosen;