What are the precautions for winter car film?

Question 1: What are the ideas of winter car film? Is the movie as expensive as possible? The film is not seasonal, but the temperature in winter is not high, which belongs to the off-season of film pasting. In hot summer, most people will consider laminating. In fact, each has its own advantages. There are many people pasting films in summer, so you need to make an appointment to queue up. The master posts all day, and it is hot, which is a great test for physical strength and patience. There is no need to queue up in winter, and the master posts more attentively, so don't worry. The film is not a single thermal insulation, but also has ultraviolet isolation and explosion-proof functions.

In winter, the film will dry slowly, and the time without lifting the window will be longer, 3-7 days, and three days in summer palace will be enough. Others are no different.

It is best to wear a film that suits you, not the more expensive the better. It's like a woman wearing clothes, which are beautiful and expensive, but it's wrong to wear clothes that are too small or inappropriate for her age or occasions. Is it beautiful? Of course not. No matter how cheap clothes are, as long as they are of good quality, the right size and comfortable to wear, they look good. The same is true of movies.

It is understandable that high-end cars are expensive to stick a good film, but it is not necessary to stick high-end cars. The same is true of economy cars. You can choose the cheap one, but it's not that you can't stick to it well. Movies are for your own use, for your own enjoyment, and for your own use is the most important thing.

Question 2: What are the precautions for car film? There was not much problem before the film was applied to the car. Just clean the window. The most important thing is to pay attention to the problems after filming. 1 try not to wash the car for three days to avoid the car film falling off. 2. The defogging line of the rear window can't be electrified within one week, and heating is easy to cause membrane deformation. 3. Do not lift the film doors and windows for a week to prevent the film from shifting and rolling.

Question 3: What are the precautions for winter car film? 1. Within 48 hours after the membrane construction is completed, contact the after-sales department for quality inspection and take water from the remaining water points again.

2. It takes 5-7 days for the car film to be fixed on the window. In the meantime, don't open the window, and don't clean or wipe the car film, so as to avoid the incomplete adhesive film shifting.

Please don't tear off the window lift sticker posted by the film maker for you within 7 days.

3. Do not turn on the defogging or heating device within 0/0 days of the front gear/KLOC and 30 days of the rear gear; Within 72 hours after sticking the film, the air conditioner should not blow the film directly, and the gear of the air conditioner should be below the second gear, otherwise the film will become warped.

4. If the edge of the film bubbles, it should be repaired within 24 hours. If the treatment time is exceeded, because the glue around the bubble has dried out, the periphery of the film can no longer move, and creases will definitely appear during treatment.

Question 4: What precautions should be paid attention to in car film? There are seven points to note in this film:

1. After the Wrigley film is attached to the front bumper, stop during the day and get as much sunshine as possible, which will make the front bumper film dry faster. It usually takes about half a month to dry completely, including the rear gear.

2. Avoid lifting the window within three days after the car is pasted. Because there is still water between the window glass and the newly pasted film, it is easy to cause the edge of the film to fall off when lifting the window glass, which will seriously make the film unable to stick to the glass again.

Don't wash the car for three days. Due to the high water pressure of professional car washing equipment, water easily penetrates from the edge of the window, which will cause high water content in the edge of the glass and film, and it is easy to cause the edge of the film of Wrigley car to fall off when the window is lifted three days later.

4. Vehicles with skylights are driving within three days, especially at high speed. Don't open the skylight. Because there will be convection in the air inside and outside the car after the skylight is opened, it is easy to cause the upper edge of the front baffle to fall off.

5. If the edge of Wrigley car film bubbles, it should be repaired at the construction site within 24 hours. If it exceeds the time, it will be dealt with. Because the glue around the bubble has dried up, the periphery of the automobile film can no longer move, and creases will definitely appear when handling.

6. It is forbidden to stick the super adhesive label directly on the film within one month after sticking the film, so as not to cause the separation between the film and the glass.

7. After pasting Wrigley film in winter, it is recommended not to lift the window or wash the car for a week.

Question 5: Can cars be painted in winter? What problems should be paid attention to in winter film mulching? The only thing to note is that after plastic film mulching in winter, the glass may not rise or fall for 10 and a half days, and the water evaporation in the film is slower. Don't wipe the solar film with a towel, and don't open the rear windshield. If there is a film on the front windshield, pay attention to the smaller air volume when blowing and defogging the front windshield. If there is any problem, go to the film pasting place to solve it in time.

Question 6: What should I pay attention to after pasting the car (1)? Do not start the side window within 48 hours after pasting;

(2) After a week of pasting, do a quality inspection back to the pasting place;

(3) Do not start the defogging heating wire within 15 days after sticking the film;

(4) If the membrane edge bubbles, it should be repaired at the construction site within 24 hours. If it exceeds the time, it will be dealt with. Because the glue around the bubble has dried up, the periphery of the film can no longer move, and creases will definitely appear when processing;

(5) Within 15 days after pasting the film, please do not paste some items with suction cups on the film, such as GPS suction cup base and some plush ornaments with suction cups;

(6) Please don't stick the self-adhesive label directly on the membrane, please ask the construction unit for the annual electrostatic transfer sticker of Gu Wei specialty;

(7) Don't worry if there is fog between the film and the glass after pasting, it will naturally dry out and disappear within 4- 10 weeks.

Question 7: Precautions for car film 1: After the car film is attached, avoid lifting the window for three days; 2: Don't wash the car within three days; 3: Vehicles with skylights are driving within three days, especially when driving at high speed, do not open the skylights; 4. It is recommended not to lift the window and wash the car one week after filming in winter. It takes about a month for the front and rear gears to dry completely. 5. If the edge of the membrane bubbles, it should be repaired at the construction site within 24 hours. If it exceeds the time, it will be dealt with. Because the glue around the bubble has dried up, the periphery of the membrane can no longer move, and creases will definitely appear during treatment. 6. It is forbidden to stick the super adhesive label directly on the film within one month after sticking the film, so as not to cause the separation between the film and the glass. 7. Car film should also understand the car inspection policies of various cities. For example, in some cities, if the visible light perspective ratio between the windshield used in the driver's visual area and the glass other than the windshield is less than 70%, the annual inspection will not pass. When sticking the car film, the triangle area of the front window cannot be stuck, otherwise it will affect the normal annual inspection of the vehicle.

Question 8: What are the precautions after the car film is applied? 1, don't lift the glass for five days after filming, and don't lift the glass on cloudy and rainy days seven days a week!

2. Please do not start the defogging heating wire within 30 days after pasting.

3. If blistering is found on the membrane edge, it should be repaired at the construction site within 24 hours.

4. Please don't stick the adhesive label directly on the film. You can use the electrostatic sticker in the store for annual inspection, and electrostatic adsorption will not cause harm to the film.

5. It is normal that there is mist between the film and the glass after pasting. Please don't worry, 1-2 months later.

6. Don't blow the front defogging tuyere within one week after the front bumper film is pasted.

7. After cleaning the inside of the glass, you can wipe it with a clean, soft and lint-free microfiber towel. Be careful not to have sand and other stolen goods in the towel to avoid sharp things scratching the film.

8. Avoid hard objects touching the film to avoid scratches.

Question 9: Can I take pictures of cars in winter? Car film regardless of season, winter concern. Now the professional car film is dust-free closed workshop film. The workshop is kept at constant temperature and humidity, so the film is not affected by season and weather. However, in winter, the film may spread slowly, but it does not affect the quality, so it doesn't matter.

Question 10: What should I pay attention to for car film? If you want to have a good effect, you must grasp several points. First of all, we need product fidelity. Now all good auto beauty shops can do heat insulation tests. Before and after pasting, you can ask the store to do tests to see if it meets the insulation requirements. If it is a brand-name film, it must be a formal guarantee, and it is doubtful whether it is guaranteed or not. Secondly, we must find a well-built shop. The membrane is divided into three parts and seven parts. If the construction is not good, the membrane will be dirty and easy to bubble. Finally, do not lift the glass within 3 days after pasting, so as not to affect the firmness of pasting. Don't coat the film with super glue for a week. Of course, the good effect needs to match the color of the car body, and so on, which requires you to choose a store with good service quality and more reliable.