Traditional Culture Encyclopedia - Weather forecast - Does it matter to stick tiles indoors in rainy days?

Does it matter to stick tiles indoors in rainy days?

Does it matter to stick tiles indoors in rainy days?

Does it matter to stick tiles indoors in rainy days? Many people want to decorate their houses quickly, so they will continue to decorate in rainy days, but it will be very troublesome to decorate in rainy days because it is easy to get wet indoors in rainy days. Does it matter to stick tiles indoors in rainy days?

Does rainy day affect the laying of indoor tiles? 1 1. Rainy days are not suitable for indoor tile laying, because too much moisture will affect the quality. In southern cities, the air humidity is high, the tiles are too good, and the water can't penetrate. Try to spread them on sunny days. After the renovation, the ground will regain its moisture, and it will take more than 40 days for ventilation in sunny days.

2. The biggest problem in the rainy season decoration is that the moisture content of the large core board itself is high, and it will absorb more moisture in the wet rainy season. Once in the dry season, it will cause serious cracking and deformation, which is also the biggest hidden danger of decoration in the rainy season.

3. For tiles, it is easy to cause the tiles to absorb too much water in rainy days, which leads to the tiles easily cracking or even falling off. If you don't buy better brand tiles, the problem will be more serious.

Can I stick indoor tiles on rainy days?

Too fast drying of cement mortar will affect the strength of bonded tiles, and rainy days can just increase the bonding time, which is beneficial to the molding strength of cement mortar.

According to the relevant national standards, the initial setting time of portland cement should not be earlier than 45 minutes, generally 1 ~ 3 hours, and the final setting time should not be later than 390 minutes, generally 5 ~ 8 hours.

Two days later, the cement mortar has solidified. It should be noted that at this time, the cement mortar has not reached the full strength, only about 50% strength.

Walk as little as possible and don't do strenuous exercise. The total strength of cement mortar takes about 10 days. After the masons are finished, the carpenters usually come to the fields.

The time interval between the entry of woodworking materials and the completion of tile laying should be more than one week, so as to avoid adverse effects on floor tiles when handling materials, such as unevenness and hollowing.

In fact, with the improvement of technical level, various decoration materials have better and better adaptability to climate. The workability and constructability are getting better and better, which greatly improves the working efficiency of construction personnel and ensures the construction quality.

Does indoor tiling have an effect on rainy days? 2 The construction weather does have an impact on the construction, but it has little impact on indoor tiling, but has a greater impact on outdoor tiling. First, it is dangerous to stick external wall tiles in rainy days, mainly because of the safety of construction workers; Secondly, under the scouring action of rain, it is easy to wash away the cement that sticks to the tiles, making the tiles non-stick and affecting the paving effect of the tiles.

For ceramic tiles, it is easy to cause excessive water absorption in rainy days, and it is easy to crack or even fall off in the later stage. If the quality of tiles is not good, there may be more problems.

Key points of tile laying:

1. When plastering with cement mortar, the wall tiles should be soaked in water, and the floor tiles should not be used. Wall tiles should be soaked in water for 2~4 hours, subject to no foaming. The purpose is to make the water-absorbing ceramic tile unable to absorb the water in the cement layer quickly, thus making the cement lose its corresponding performance.

2. Before laying floor tiles, the thickness of bonded mortar should be determined according to the design requirements, and the total thickness and surface flatness of stone and floor tiles should be controlled by pulling the reticle. When sticking floor tiles, you should also do slurry sweeping treatment in advance to keep the ground clean and free of sundries. It is best to use a professional napping roller to nap the wall tiles.

3. Pay attention to the ratio of cement to sand: too much cement shrinks too fast, and too little cement is easy to stick. Under normal circumstances, wet plastering is generally used for wall tiles, and the amount of cement is more; Floor tiles are generally dry-bonded, which requires more sand.

If the wall is new, it's best to hang the net first, and then plaster it. If you need to hang heavy objects such as water heaters, it is best to use lightweight bricks of more than 8 cm.

4. After paving at1hour, the cement, caulking agent or other sticky objects left on the brick surface should be wiped clean immediately, because it is difficult to clean them after being stuck like caulking agent for four hours.

5. After paving 12 hours, remember to knock on the brick surface for inspection. If you find that the drums are free, you should relocate them immediately. The overall empty drum phenomenon of floor tiles should be controlled within 3%, and the empty drum on the main channel must be reworked. 3% refers to a single corner empty drum, the whole block shall not be empty drum.

It will be 6.24 hours before laying bricks. Thoroughly scrub, mix the detergent with clean water, and thoroughly clean the tiles.

7. There are also some stresses on the joint of ceramic tiles: the joint of antique ceramic tiles is generally 2~3mm, the wall tiles 1~ 1.5 mm, and the floor tiles1~ 2 mm. The thickness and height of bricks are generally about 3cm.

Does rainy day affect the laying of indoor tiles? 1. Rainy days will affect the wall decoration. When decorating a house, people should scrape putty and paint the walls. Some people who pursue quality will also buy wallpaper that matches the style of home decoration. But all these must be carried out on the premise that the wall is dry.

First of all, we should do a good job of drying putty at the grass-roots level during construction. The wall should be painted with putty three or four times before painting, and each layer should be painted in a dry condition for the next step. Secondly, when painting or pasting wallpaper, we should wait until the wall is dry before starting construction, otherwise it will cause problems such as wall cracking, peeling and moldy wallpaper.

Second, when it rains, the indoor air is very humid. So there are many places to pay attention to when laying the floor and painting. Under normal circumstances, wood materials will absorb water, expand and deform due to the influence of humidity.

When paving the floor, it is necessary to ensure that the ground is dry, and because the wood will expand due to moisture, it is necessary to keep the gap small when paving to prevent the shrinkage gap of wood from getting bigger in dry weather, especially for solid wood floors and composite floors.

Third, when it rains, tiling has no effect. Because in the case of normal tiling, it is necessary to sprinkle some water in advance, especially in the open air. But the air humidity is high in rainy season, so it is not necessary. The ceramic tile itself should keep a certain amount of water, so that it will not quickly absorb the water in the cement to produce a chemical reaction, which will lead to the decline of cement strength and lead to the phenomenon of hollow bricks.

What should I pay attention to when tiling the whole house?

1. Tiles are soaked in water as needed: Have friends learned anything from the above explanation of what tiles on the wall are stained with? At that time, it was very troublesome to stick tiles no matter what method was used, so special attention should be paid when sticking tiles.

For example, tiles must be soaked in water before pasting, but according to the construction progress of workers, tiles must be soaked in water, and tile merchants who have soaked in water refuse to return them.

2. Make a brick arrangement plan before tiling: Make a brick arrangement plan before tiling, which not only avoids the unexpected situation that tiles have to be removed and repaved due to uncoordinated proportions, but also avoids the easy wear of tiles.

3. Correct mix proportion of cement sand: Because cement mortar is easy to expand and tile cracks after paving, it is necessary to control the mix proportion of cement sand. If it is a wall brick, the proportion of cement sand is 1:3, and the floor brick is 1: 2.

4. The joint of ceramic tile should not be too small: due to the influence of weather, the glaze will crack after thermal expansion and contraction, so the joint of ceramic tile should not be too small during construction. When buying tiles, ask the merchant how many seams to leave.

5. It is best to fill the joints until the tiles are dry. Tile jointing can only be carried out after the tiles are dry and solid. If you do it right away, it is easy to loosen the tiles, which will lead to the tiles falling off after a long period of use and avoid hidden dangers to life.