What should I do if a piece of wooden floor becomes warped?

What should I do if a piece of wooden flooring is warped?

What should I do if a piece of wooden flooring is warped? Nowadays, for the sake of convenience and beauty, wooden floors are all used. However, families with wooden floors may encounter such a problem, that is, the wooden floor may warp under the action of external force. So what should I do if a piece of wooden floor warps? What should I do if a piece of wooden floor warps1

< p> 1. The reason why the wooden floor is warping

1. There is no expansion joint left when laying the floor, causing it to warp

Due to the lack of gaps between the wooden floor and the wall base during the paving process Because of the gaps, the floor does not have enough elastic expansion space after being wet during the rainy season, so it naturally arches. This type of arching is common and is typically characterized by a wooden floor arching over the foot that collapses and that arches when the foot is lifted. For this kind of arching, as long as the expansion joint of the floor can be cut, it must be discovered and dealt with in time. Vaulted wood floors must be replaced once they have been arched for a long time.

2. After laying the wooden floor, moisture causes it to warp.

Some consumers’ wooden floors have been damaged by water. If exposed wood flooring is covered in moisture, it may cause the pads to swell and the top wood flooring to lift. At this time, if you step on the raised wooden floor, you will find out how to step on the wooden floor without collapsing. To fix this situation would be more troublesome, we would have to lift the wood flooring and underlying mat and then repave it.

2. Repair methods for warped floors

1. If the floor warps due to moisture, please drain the floor water. At the same time, the water absorption device can be used to absorb the water vapor soaked in the joints of the floor, or use a hair dryer to blow cold air.

2. If the floor in your home is warped, it is because the floor itself is dry. Then you can further turn on the humidifier at home to increase the humidity of the ground. It can also be improved by increasing the air humidity. You can turn on the air conditioner to adjust the humidity. Generally, the indoor temperature should be 28 degrees Celsius, and the humidity should not be lower than 40 degrees Celsius. Generally, in rooms with wooden floors, the humidity is usually between 50 degrees and 50 degrees. But you are not told to pour water on the wooden floor. Only by avoiding large-scale "water replenishment" can you protect the wooden floor.

3. If after a period of time, the seams are raised but too far away from the previous layer, you can try to wax the floor after the water layer after waxing is almost the same as the original one. If the color and shape of the waxed floor differ significantly from the original floor, then only the floor will be partially replaced.

If the floor is raised, it is correct to deal with it as soon as possible. Once the warping is not dealt with, the damage to the wooden floor will indeed become more and more serious. When the floor is warped, repairs can be made based on the cause. The waterproof function of some consumers' home wooden floors is not very good, or water intrusion occurs, causing the wooden floors to be covered with moisture. It is very easy for the wooden floors to swell and the top wooden floors to be lifted. Then it is recommended to buy branded wooden floors, which are less likely to deform. What to do if a piece of wooden floor is warped 2

How to repair a warped wooden floor:

1. How to repair a warped wooden floor---absorb water

< p> If the weather is humid and causes the floor to warp, just absorb the moisture on the floor. The water in the small seams of splicing needs to be dried with cold air from a water absorber or hair dryer.

2. How to repair the warped wooden floor---squeeze with heavy objects

If only a small area is warped, you can put heavy objects on it. After a while, the floor will be It will automatically restore to its original state. If the damp area is too large or the deformation is severe, the floor needs to be re-paved. In addition, in daily life, you should often open windows for ventilation to evaporate indoor moisture.

3. How to repair the warped wooden floor---wax or replace the floor

If the color of the floor is too different after soaking in water, you can try to wax the floor. , to restore the floor to its original state. If it has not recovered, it can only be partially replaced.

4. How to repair a warped wooden floor --- air humidification

If the warped floor is caused by dryness, the problem can be solved by increasing the ground and air humidity. But you need to use a humidifier to adjust the temperature, and don't "water supplement" too much. In addition, it is best to keep the indoor temperature at 28 degrees and the humidity at 50 to 70 degrees.

What are the reasons for warping of wooden floors:

1. Not enough expansion joints

Before the floor is laid, the wooden floor and wall heels must be reserved. Leave enough gaps so that the floor has a place to extend if it gets wet. If there are no gaps, it will lift. In addition, in order to prevent the wooden floor from lifting, the expansion joints of the floor must be cut larger.

2. Warping of the cushion caused by moisture

Some families’ wooden floors are laid on the basis of floor tiles. The wooden floors laid in this way are more susceptible to moisture, causing the wood to become damp. The floorboards are lifted.

3. In addition, there are other moisture factors

The moisture content of the building walls and floors is relatively high, and the ground is not completely dry during the paving process. Insufficient moisture-proof isolation measures will cause the wooden floor to become warped due to moisture. What to do if a piece of wooden floor is warped 3

The simplest method to repair the warped floor

1. Absorb the water

If it is caused by moisture on the floor If the floor is raised, drain the water on the floor. At the same time, you can use a water absorber to suck away the water vapor in the splicing gaps of the water-soaked floor, or use a hair dryer to blow dry with cold air.

2. Squeeze with heavy objects

If the joint is only a small area of ??warping, you can use heavy objects to press it. After a while, the wooden floor will return to normal on its own. . After you find that the solid wood floor is damp, you should immediately lift the floor around the room to disperse the moisture. This can alleviate the degree of deformation. If the damp area is large and the degree of deformation is large, it is recommended to resurface the base layer and dry it before re-paving the floor.

3. Wax or replace the floor

If after a period of time, the seams bulge, but they are too far from the original floor, you can try to wax the floor. Waxing, the water-soaked floor after waxing will basically be the same as the original. If the color and shape of the floor after waxing are still very different from the original state, then the only option is to partially replace the floor.

4. Air humidification

If the floor in your home is raised due to indoor dryness, you can solve the problem by increasing the humidity of the ground and air. However, large-scale "water replenishment" should be avoided. Humidifiers and air conditioners are recommended to adjust the humidity. It is most suitable to keep the indoor temperature at 28 degrees, and the humidity to be kept at 50 to 70 degrees, and not lower than 40 degrees.

Tips for repairing warped floor tiles

1. Remove all the warped bricks, then clean the bottom of the bricks, smooth them with cement, and then remove the bricks. Just put it on.

2. Find a cutting machine and cut slits on the raised floor. Be careful to cut the areas that have just become raised, otherwise they will not be cut. Lift up all the raised parts of the floor tiles and sweep them clean underneath. Just apply floor glue to each floor and stick it on.

3. Floor tiles warp and burst, which usually occur when the temperature changes drastically, including freezing or hot weather. The simple reason is that floor tiles and other building materials expand and contract with each other due to thermal expansion and contraction. This is usually caused by improper decoration and construction. Caused by the quality of building materials. When laying floor tiles, attention should be paid to the use of cement above No. 425 for laying floor tiles. The sand should be filtered and medium coarse sand, with a ratio of 1:2, and a 1 mm expansion joint should be reserved.