What is the driving computer display screen of the EX series vehicles of BAIC New Energy?

Figure-Partial view of instrument cluster: display screen of trip computer

The display screen of the driving computer can display a variety of different driving interfaces, and the switch can be adjusted by button A/B. ..

It should be pointed out that:

In cold areas (-25℃ and below), the display content of the instrument may be slow to respond. In extremely cold areas, the instrument may not even start normally, but with the increase of the temperature in the car, the instrument will gradually return to normal working condition.

Figure-Driving Computer Display: Voltage Value

Voltage value:

Refers to the voltage value of vehicle power battery.

Illustration-Driving Computer Display: Vehicle Speed

Speed:

Indicates the current vehicle speed, and the right side is shown as

The word speed.

Illustration —— Driving computer display: ammeter

Ammeter:

The current value indicates the current charging/discharging of the power battery, a positive value indicates that the power battery is discharging, and a negative value indicates that the power battery is charging.

Illustration-display of driving computer: speed value of driving motor

Speed value of driving motor:

Indicates the current speed of the drive motor.

Illustration-Driving Computer Monitor: Instantaneous Power Consumption

Instantaneous power consumption:

Indicates the instantaneous power consumption intensity when the vehicle is running, and the power consumption increases from the middle to both sides in turn.

Illustration-Driving Computer Display: Maintenance Mileage

Maintenance mileage:

The initial default maintenance mileage of the instrument is 10000km, and the subsequent maintenance is once every 10000km. When the vehicle maintenance mileage is less than 150km, every time the start switch is in the "ON" position, the text prompt "Please maintain the vehicle" will be displayed on the display screen of the driving computer, which will be automatically eliminated after 5 seconds.

It should be pointed out that:

When the instrument prompts "Please maintain the vehicle", please maintain the vehicle as soon as possible. When the instrument is in the maintenance mileage interface, press and hold the A 10s button to reset the maintenance mileage to 10000km.

Illustration-Driving a Computer Monitor: Average Power Consumption

Average power consumption:

Average power consumption means the average power consumption when the vehicle is running, and the unit is kWh/100 km, that is, KWH/ 100 km.

It should be pointed out that:

"—"will be displayed at the initial stage of vehicle startup. As the driving time becomes longer, the vehicle controller will continuously calculate the average power consumption during the current driving period and display it through the instrument.

Illustration-Driving Computer Display: Electric Meter

Electricity meter:

The electric meter is divided into ten units.

When there are 3 cells left, it will be orange;

When there is only one cell left, the line segment displayed is red. Please choose a nearby charging pile to charge the vehicle as soon as possible.

Illustration-Driving computer display: cruising range

Cruising range:

Indicates the distance that the vehicle can travel under the current power, and the minimum display accuracy of the instrument is 1km.

When the cruising range is displayed as "-"and the energy bar disappears, it may be caused by the following reasons:

1. The remaining power of the power battery is too low, so drive it slowly and charge the vehicle as soon as possible.

2. When the start switch is in the "ON" position, the vehicle controller starts to calculate the cruising range, and the instrument will display the current cruising range after a delay of several seconds.

It should be pointed out that:

The cruising range will be affected by driving mode, weather, temperature, driving environment and other data.

Illustration-Driving computer monitor: gear indicator:

The vehicle gear indicator is located on the LCD screen of the driving computer. The EX200 vehicle has four gears, namely, R, N, D and E, and the EX260 vehicle has four gears, namely, R, N, D and S. As shown in the figure, it is displayed in the N gear position.

The above figure will appear on the left side of the gear, and the number 1/2/3 indicates the current energy recovery intensity. The larger the number, the stronger the recovery intensity.

Illustration-Driving Computer Display: Total Mileage, Subtotal Mileage and Subtotal Mileage:

The total mileage is the accumulation of all the mileage when the vehicle leaves the factory. Resetting settings cannot be done through buttons. The digital meaning of the total mileage is 6 digits, and the accuracy is 1km. The display range is 0 ~ 999999km, and it will stay at 999999km when it reaches the maximum.

The effective digit of subtotal mileage is 4 digits, and the accuracy is 0. 1km. The display range is 0 ~ 999.9 km. When the maximum value is reached, the subtotal mileage will be automatically cleared and recalculated. When the vehicle stops, the calculation of subtotal mileage stops. Pressing button B for more than 3 seconds will clear the mileage subtotal.