Emergency plan for preventing rainstorm in factory

Emergency plan for preventing rainstorm in factory

In daily study, work or life, some unexpected things will inevitably happen. In order to control the development of accidents, it is usually required to prepare emergency plans in advance. How to write the emergency plan to play a better role? The following is the emergency plan for preventing rainstorm in the factory area that I have compiled for you. Welcome everyone to learn from it. I hope it helps you.

Emergency plan for preventing rainstorm in the factory 1 In order to prevent lightning and rainstorm from harming the safety of mine facilities and personnel in rainy season, strengthen the lightning protection and rainstorm prevention work in coal mines, establish an efficient and orderly disaster relief organization, improve the overall level of disaster prevention work, and effectively do a good job in mine disaster prevention work quickly and efficiently, the emergency plan for lightning protection and rainstorm prevention is specially formulated.

I. Scope

This plan is applicable to lightning protection and rainstorm emergency work within the mining area of Xuzhou Li Tang Mining Co., Ltd.

Second, the organization and responsibilities

1, emergency organization system

Set up a leading group for lightning protection and rainstorm prevention, be responsible for the leadership of lightning protection and rainstorm prevention in this mining area, and supervise and inspect the lightning protection and rainstorm prevention work. Responsible for the rescue of sudden lightning storm disasters, the team members must quickly rush to the relevant posts to direct the handling of problems. Team members are required to be familiar with the on-site working environment and have the ability to deal with unexpected problems in time.

Team leader: Song Shigang

Deputy leaders: Wang Fuhai, Liu Chengwen and Lu Xianwei.

Members: Cheng, Cenfeng, Song,,, Zhu.

2. Specific responsibilities

(1) Be responsible for studying and formulating specific measures and opinions on lightning protection and rainstorm disaster work arrangement and accident emergency treatment in this area;

(2) Responsible for the emergency support and response to lightning and rainstorm disasters;

(3) Responsible for joint inspection, quality supervision and acceptance of lightning protection and rainstorm prevention;

(4) Responsible for the handling, rescue and accident aftermath of lightning and rainstorm disasters;

(5) Responsible for the construction and management of lightning protection and rainstorm accident handling team;

(6) Responsible for organizing the deployment of personnel and materials;

(7) In case of serious disaster, take countermeasures and report to the superior in time.

Three, disaster prevention requirements and points

In the case of lightning and rainstorm, according to the actual situation of thunderstorm, the leader of the emergency plan team decided to release the start and end time of the emergency plan for lightning protection and rainstorm prevention in our mine and organize its implementation. Relevant personnel are on standby at any time to ensure the safety of life and property of employees in our mine.

IV. Safe implementation of lightning protection and rainstorm prevention

1. According to the specific conditions of the company's buildings and related facilities, check the connection between the existing lightning protection devices and the metal objects on the roof, whether the down conductor is broken or corroded, whether the soil near the grounding device sinks, and whether the drainage pipeline is blocked. Clean all flood discharge pipes to ensure smooth flow.

2. Conduct annual inspection of all lightning protection products and facilities. Do a good job in the daily maintenance of lightning protection devices, and designate a special person to be responsible.

3. During a thunderstorm, employees in the factory are forbidden to walk near high-voltage lines to prevent high-voltage discharge from hurting people.

4. In case of lightning, when the high-voltage line is disconnected from the ground, contact Fengxian Power Supply Bureau for power outage and evacuate people as soon as possible. Don't go near the break point within 30 meters, and evacuate employees in an orderly and organized manner.

5. In case of water disaster, the personnel on duty should report to the planning team in time, and the members of the planning team should be under unified command and assume their respective responsibilities.

6. Install submersible pump in the cable trench of the ground substation, and drain the water into the main drainage ditch in time when the accumulated water is serious.

7, rainy days, mechanical and electrical personnel on duty to inspect the factory, the focus is on the substation and distribution station.

8, thunderstorm days must arrange personnel on duty in the substation, to ensure the normal power supply.

9, the rainy season three prevention materials must meet the requirements. Mainly check the implementation of water pumps, drainage pipes, switches, cables, iron hoists, woven bags, raincoats, rain boots, canvas, miner's lamps, safety helmets and other materials, and hang special cards for management.

10, before the thunderstorm season comes, the hidden dangers of double-circuit power supply lines must be handled well:

(1) Cut down trees that pose a threat to the power supply line along the way to prevent the power supply line from tripping due to grounding or short circuit caused by contact between overhead lines and trees in thunderstorm weather;

(2) Replace defective porcelain bottles and stay wires;

(3) All lightning arresters must be tested and qualified.

1 1. Check the lightning rods, lightning wires and grounding grids of all buildings, and take measures to rectify those that do not meet the requirements.

12. If the grounding resistance is greater than 2 ohms, salt or other measures must be taken to reduce the resistance to below 2 ohms.

13. In case of frequent lightning and rainstorm, the personnel on duty of the preplan team shall be responsible for starting and stopping the main and auxiliary winches according to the weather conditions.

14. During the thunderstorm, the leading group of emergency plan work should arrange inspection, and the responsible person should rectify the existing problems within a time limit.

Five, 35KV ground substation emergency plan

(1) facility maintenance

Power accidents are mainly prevented, and the main equipment in the substation should be regularly maintained and inspected. The main measures are as follows:

1, quoted from the 35KV two-way mine power supply of Litang Coal Mine ground substation (the first Li I line and I line), to ensure the first run, and the other one must be hot standby.

2, do a good job of 35KV substation equipment maintenance, to ensure that the equipment platform in good condition.

3. Patrol the lines beyond 35KV once a month to ensure the normal power supply of the power supply lines from Shouxian Substation and Shunhe Substation to Litang Coal Mine.

4. Strengthen the contact with the superior substation and the dispatching room of Fengxian Power Supply Bureau.

5, the personnel on duty strictly implement the power supply technology operating rules and the rules and regulations of the substation.

6, in strict accordance with national standards, according to the provisions of equipment performance testing.

7. Regularly set and check the relay protection to ensure that the protection is sensitive and reliable.

8, found that the equipment anomalies or defects should be timely investigation and handling, leaving no hidden dangers.

(2) Normal operation mode of the line

There is a ground substation in the ground industrial site of Litang Coal Mine, in which two power sources (the first I line) are led out from Zitong 1 10kV substation, and the other route is led out from Shunhe 1 10kV substation (Li Shun I line). This line is overhead, and the conductor is LGJ- 185.

(3) Active lines and emergency response to accidents

Active power lines: the first Li I line in Litang Coal Mine supplies power and the Li Shun I line in Litang Coal Mine supplies power.

Accident emergency: When the primary circuit is out of power, the faulty line should be cut off quickly and the active line in the other circuit should be connected.

(4) Substation accident power failure

If the first Li I line (or I line) in Litang Coal Mine can't restore power supply temporarily after power failure, it is necessary to switch the switch in time to supply power to the I line (or I line) movable line in Litang Coal Mine.

In case of power failure of Li Shun I Line (or Juri I Line) in 35KV Litang Coal Mine, the personnel on duty should first determine the cause of the accident, deal with it quickly, and report the situation to the mine operation department and superior leaders. If the accident line is the power supply network in the mine, the accident network should be removed first, and then the power supply should be restored; If the superior substation loses power or the line fails, another line should be activated immediately.

The specific operation steps are as follows:

Li Shun I line accident power outage operation:

1, turn off switches 35204, 35203 and 10206, and confirm the disconnection;

2. Check whether the incoming switching power supply of 35 104 is charged and confirm that it is charged;

3. Confirm that the incoming switch handcart of 35 104 is in the working position;

4. Turn on the 35 104 switch and confirm that it is closed;

5. Check whether the instructions of 35 104 switching power supply are normal and confirm that they are normal;

6. Confirm that the 35 103 switch is in the working position; Close the switch 35 103 and confirm that it is closed;

7. Check whether the 1 # 5000 kva transformer works normally, and confirm that it is normal;

8. Check whether the 10KV 10 105 incoming line cabinet and the original 10KV feeder cabinet are closed, and confirm that they are in normal working condition.

Emergency power outage operation of Shouli Line 1:

1, turn off switches 35 104, 35 103, 10 105, and confirm the disconnection;

2. Check whether the incoming switching power supply of 35204 is charged, and confirm that it is charged;

3, confirm the 35204 incoming switch handcart in the working position;

4. Turn on the 35204 switch and confirm that it is closed;

5. Check whether the instructions such as 35204 switching power supply are normal and confirm that they are normal;

6, confirm the 35203 switch in the working position; Turn on the 35203 switch and confirm that it is closed;

7, check whether 2 # 5000 kva transformer works normally, and confirm its normal;

8. Check whether the 10KV 10206 incoming cabinet and the original 10KV feeder cabinet are closed, and confirm that they are in normal working condition.

After emergency power failure and brake switching operation:

Restore the power supply of each power supply location, and contact the superior substation and the dispatching room of Fengxian Power Supply Bureau until the equipment runs safely and normally. After confirming that it is normal, put the first Li I line (or I line) and main transformer in Litang Coal Mine into hot standby state.

Six, 35KV substation belongs to the main load emergency plan

(a), the main shaft winch room high voltage power outage emergency plan

1. If the power supply of line I (or line II) of the main shaft winch room cannot be restored temporarily after power failure, the brake must be switched in time to supply power to the active line of line II (or line I) of the main shaft winch room.

When the power supply of line I (or line II) in the main shaft winch room is out of power, the personnel on duty should judge whether it is an accident or other reasons in a very short time, deal with it quickly, and report the situation to the mine dispatching room and superior leaders. If the person on duty judges that it is an accident trip, the equipment or line at the accident point should be cut off first, and the other circuit power supply should be activated immediately.

The specific operation steps are as follows:

Main shaft winch room I line accident power outage operation:

(1) Confirm that the I-line power supply of spindle 10 109 is in the off position.

2. Confirm that the handcart of 10209 spindle II line is in the closing position.

(3) Close the spindle 10209 line II.

(4) Restore the normal power supply of the spindle II line.

5] Check the fault cause of spindle I line, and put the power supply into hot standby after it is confirmed to be normal.

Emergency power failure operation of line II of main shaft winch room:

(1) Confirm that the power supply of spindle 10209 line II is in the off position.

2. Confirm that the handcart of 10 109 spindle I line is in the closing position.

(3) close the spindle 10 109 line I.

(4) Restore the normal power supply of spindle I line.

5] Check the fault cause of spindle II line, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) immediately switch all spindle winches to the stop position.

⑵ Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply, and resume main shaft hoisting after repair.

(2) Emergency plan for winch room during high-voltage power failure.

1. If the power supply of line I (or line II) of the auxiliary shaft winch room cannot be restored temporarily after power failure, it must be supplied to the active line of line II (or line I) of the auxiliary shaft winch room in time.

When the power of line I (or line II) in the auxiliary winch room is cut off, the personnel on duty should judge whether it is an accident or other reasons in a very short time, deal with it quickly, and report the situation to the mine dispatching center and superior leaders. If the personnel on duty and electrical maintenance personnel judge that it is an accident trip, they should first cut off the equipment or lines at the accident point and immediately activate the other circuit for power supply.

The specific operation steps are as follows:

During the power failure operation of I-line accident in winch room:

(1) Confirm that 10 108 auxiliary shaft I line power supply is in the off position.

⑵ Confirm that 10208 auxiliary line II handcart is in closing position.

(3) Close the auxiliary shaft 10208 line II.

(4) Restore normal power supply of auxiliary shaft II line.

5] check during I line fault reason, confirm the normal power supply into hot standby.

Emergency power failure operation of line II of auxiliary winch room:

(1) Confirm that the power supply of the auxiliary shaft 10208 line II is in the off position.

2 confirm 10 108 during I line handcart in the closing position.

(3) Close the I line of 10 108 auxiliary shaft.

(4) Restore normal power supply of auxiliary shaft I line.

5] Check the fault cause of the auxiliary shaft II line, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) Switch all auxiliary winches to the stop position immediately.

⑵ Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply, and resume auxiliary shaft hoisting after repair.

(3) Emergency Plan for High Voltage Power Failure of Box Transformer in Compressor Room

1. If the power supply of line I (or line II) of the box-type transformer in the air compressor room cannot be restored temporarily after the power failure, the switch should be switched in time to supply power to line II (or line I) of the box-type transformer in the air compressor room.

When the I-line (or II-line) of the box-type transformer in the air compressor room loses power, the personnel on duty should judge whether it is an accident or other reasons in a very short time, deal with it quickly, and report the situation to the mine dispatching room and superior leaders. If the person on duty judges that it is an accident trip, the equipment or line at the accident point should be cut off first, and another loop power supply should be started immediately.

The specific operation steps are as follows:

Accident power failure operation of box transformer I line in compressor room;

(1) Confirm that 10 102 compressor room box transformer I line power supply is in the off position.

⑵ Confirm that 10205 compressor room box transformer II line handcart is in the closing position.

(3) Close line II of box transformer in 10205 compressor room.

(4) Restore normal power supply of box transformer II line in compressor room.

5] Check the failure cause of I-line of box transformer in compressor room, and put the power supply into hot standby after it is confirmed to be normal.

Emergency power failure operation of box transformer II line in compressor room:

(1) Confirm that 10205 power supply of box-type transformer in air compressor room is in the off position.

⑵ Confirm that the handcart of10/02 compressor room box transformer I line is in the closing position.

(3) Close 10 102 compressor room box transformer I line.

(4) Restore the normal power supply of I line of box transformer in compressor room.

5] Check the failure cause of box transformer II line in compressor room, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) Switch all compressors to the stop position immediately.

⑵ Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply and resume operation after the compressor is repaired.

(4) Emergency plan for power failure of fan room

1. If the power supply of line I (or line II) of the fan room cannot be restored temporarily after power failure, the switch must be switched in time to supply power to the active line of line II (or line I) of the fan room.

When the power supply of line I (or line II) of the wind turbine room is out of power, the personnel on duty should judge whether it is an accident or other reasons in a very short time, deal with it quickly, and report the situation to the mine dispatching room and superior leaders. If the person on duty judges that it is an accident trip, the equipment or line at the accident point should be cut off first, and another loop power supply should be activated immediately.

The specific operation steps are as follows:

Operation of I-line emergency power outage in the fan room:

(1) Confirm that the I-line power supply of the fan in the low-voltage 400v transformer room is in the off position.

⑵ Check whether the power supply of line II of low-voltage 400V transformer room fan is charged, and confirm that it is charged.

(3) Close the low-voltage 400V transformer room fan II line power switch circuit breaker.

(4) Restore the normal power supply of fan II line.

5] Check the cause of fan I line failure, and put the power supply into hot standby after it is confirmed to be normal.

Emergency power failure operation of line II of the wind turbine room:

(1) Confirm that the power supply of line II of the fan in the low-voltage 400v distribution room is in the off position.

⑵ Check whether the I-line power supply of low-voltage 400V transformer room fan is charged, and confirm that it is charged.

(3) Close the low-voltage 400V transformer room fan I line power switch circuit breaker.

(4) Restore the normal power supply of fan I line.

5] Check the fault cause of the fan II line, and put the power supply into hot standby after it is confirmed to be normal.

2. Measures to be taken when the two lines are all blacked out or the electric control cabinet fails.

(1) Turn all switches of the main fan to the stop position immediately.

⑵ Report the accident to the superior in time.

(3) Immediately organize powerful personnel to repair power supply lines or low-voltage electric control cabinets and resume operation as soon as possible.

(4) Prepare standby power supply and resume operation after the main fan is repaired.

When a 35KV power outage occurs, well workers such as Gao Ming, Han, Song Huaidong and Zhang Fusong must quickly rush to the main shaft site, open the explosion door of the main shaft, and implement natural ventilation to ensure the safety of underground ventilation.

Emergency plan for preventing rainstorm in plant area II. In order to ensure that all emergency work can be carried out efficiently and orderly in the event of destructive rainstorm in the concentrator, and to minimize casualties and property losses, this plan is formulated in accordance with the State Council's Emergency Regulations on Rainstorms in Disaster Areas and combined with the actual work of our factory.

I. Composition of emergency agencies

1, leading group

The work of preventing rainstorm disaster in plant selection is organized and implemented under the leadership of the superior leading group for preventing rainstorm and reducing disaster. The leading group for storm prevention and disaster reduction in plant selection is led by the factory director, with the deputy factory director and section chief as team members, and the plant selection scheduling as the headquarters.

2. Main responsibilities

(1) Strengthen leadership, improve organization, strengthen post responsibilities, strengthen familiarity and understanding of destructive rainstorms and rainstorm disaster prevention and mitigation, and improve the formulation of various emergency plans and the implementation of various measures.

(2) Make full use of various channels to publicize and educate earthquake disaster knowledge, organize and guide the popularization education of full-length earthquake prevention and earthquake resistance knowledge, extensively carry out self-help and mutual rescue training for earthquake disasters, and continuously improve the awareness and basic skills of earthquake prevention and earthquake resistance practitioners.

(3) Do a good job in material support, actively prepare in strict accordance with the requirements of the plan, implement substances such as drinking water, antifreeze and rainproof, emergency equipment, and strengthen management to maintain a good combat readiness.

(4) After the destructive rainstorm, take all necessary measures to organize all forces to carry out disaster reduction work in an all-round way to minimize the losses caused by the disaster.

(5) Dispatch all positive factors, quickly restore production order, and fully guarantee the stability of production and employees' lives.

Second, the imminent earthquake emergency action

1. After receiving the rainstorm and imminent rain warning (alarm) report from the superior, the leading group immediately entered a state of war, issued relevant news and alarms according to law, and was fully responsible for various earthquake-resistant work. All relevant institutions are ready to carry out rain prevention and disaster reduction tasks at any time.

2. Organize relevant personnel to conduct a comprehensive inspection of the building, block and close dangerous places, and stop all large-scale activities.

3. Strengthen the management of flammable and explosive materials and toxic and harmful chemicals, strengthen the protection of important equipment and places such as large boiler hangars and power supply and distribution rooms, and ensure the smooth progress of earthquake resistance and disaster reduction;

4. Strengthen the publicity and education of employees, and do a good job in stabilizing employees' minds.

5, strengthen all kinds of duty on duty, keep communication smooth, timely grasp the grass-roots situation, maintain the order of production and life in the factory.

6, according to the plan to carry out the material preparation.

Three. Emergency action students after the earthquake

1. Whether it is a forecast or an alarm, the leading group should immediately go to the local command post after a destructive rainstorm occurs in the local area or adjacent areas, and all rescue and relief teams must assemble and stand by in their own units within 1 hour after the earthquake.

2. Under the unified organization and command of the superior, the leading group quickly organized the factory selection for emergency rescue and disaster relief.

(1) Immediately issue an emergency alarm (continuous ringing and shouting), and organize all personnel still stranded in various buildings to evacuate: a Employees in various sections enter long and long rain shelters.

(2) Quickly close and cut off bookstores (except emergency lighting system) to prevent other disasters from breeding after the rainstorm.

(3) Quickly carry out on-site rescue work with rescuers as the main content, transfer the injured in time, and send them to the attachment rescue station for rescue.

(4) Strengthen the protection of important facilities and articles.

3. Actively do a good job in the ideological propaganda and education of employees, eliminate panic, stabilize people's hearts, quickly restore normal order, and fully safeguard social security and stability.

4. Quickly understand and master the disaster situation of the whole plant, and timely summarize and report to the company office.

The other four

1. After entering the rainstorm emergency, the plant selection headquarters issued various orders and instructions in various ways, and the leading group for earthquake prevention and disaster reduction conveyed various orders and instructions by telephone and dictation.

2, in the emergency action of earthquake relief, to cooperate closely, obey the command, to ensure the smooth implementation of government decrees and work smoothly.

;