Traditional Culture Encyclopedia - Hotel accommodation - Chinese bed-making steps
Chinese bed-making steps
2. Laying plate: Laying plate is completed in three steps.
Throw the sheet first: grab the label at the end of the sheet with your left hand, release it with your right hand and throw it at the end of the bed, then grab the sheet head with your right hand and open the sheets on the left and right sides respectively.
Second, billing: the distance between hands is about 80- 100 cm (depending on the center line of the bed sheet), palms down, grab the head of the bed sheet and press it on the mattress for about 30cm, then lift the bed sheet to a height of about 70cm, so that the air enters the end of the bed in a bulging shape. Lean forward slightly and throw the sheets out. When the air pushes the tail of the sheet away, it will adjust the sag by 35cm.
Third, wrap the corner: wrap the bedside first, tuck the bedsheets of the drooping part of the bedside under the mattress, wrap the right corner, pull up the bedsheets of the right corner with your left hand, tuck the bedsheets of the right corner under the mattress with your right hand, and then wrap the folded corner with your left hand to make a right angle. Tuck the bedsheets of the drooping corner under the mattress with your right hand, and wrap the left and right corners in the same way.
* Note: After the whole sheet is laid, the front of the sheet is on it, the label of the sheet is at the end of the bed, and the center line is in the middle. Invoicing should be positioned once, sheets should be tightly wrapped, and the four corners should be at right angles.
Third, quilt cover: quilt cover is divided into three steps.
First, hold the quilt cover, open the quilt cover on the bed surface, and then fork the entrance of the quilt cover, face up and bottom down.
Second, take the folded quilt to the end of the bed. To distinguish the quilt tail (trademark is quilt tail), grasp the quilt head with the left hand, and grasp the two corners of the quilt into the two corners of the quilt. First, align the left quilt corner with the left quilt corner, then align the right quilt corner and pull down along the quilt edge.
Third, you can straighten or swing according to your height, so that the quilt can conform to the quilt cover as much as possible. Put the quilt in the middle of the bed. The quilt should be flat and not wrinkled. The length of both sides should be consistent, natural and vertical, and should not protrude. The quilt tail should be 20 cm away from the carpet, based on the inclination of the two corners of the quilt tail.
4. Pillow case: put the pillow core flat on the bed, spread the pillow core bag mouth with both hands to let it enter the air, put the pillow core into the pillow core bag mouth, lift the upper edge of the pillow core bag mouth with the left hand, put the pillow core into the pillow core bag with the right hand, then hold the bag mouth with both hands, stir while lifting it, and finally insert the pillow core bag beyond the pillow core into the pillow core and seal the bag mouth.
Fifth, put the pillow: the pillow is flat and centered by the bedside. Placed pillows must be full, smooth around, and the pillow core is not exposed.
- Previous article:2016 Jiyuan City Bus Arrangement
- Next article:Part-time adventure sketch line
- Related articles
- What is the best route from Guangzhou to Tibet? Which is the fastest way to go by car or plane?
- What's the road condition like after 20 1 1 August from Guangyuan Baolun Town to Jiuzhaigou via Wenxian County, Gansu Province? It is better to have a picture.
- Can I stay in Zhangzhou Jinluan Bay if I am on the credit blacklist?
- How to pronounce this Dian character?
- 4 Project Tender Format Templates
- 20 19 Taiwan Province province free travel strategy
- Phuket, the largest island in Thailand, is located in which country?
- How far is the International Exhibition Store of Shanghai Goldman Sachs Hotel from Hongqiao high-speed railway station and how to get there ~
- Is there a bus to Changbai Mountain Airport after ten o'clock in the evening?
- What are the software for ordering high-speed rail? What software should I download to take the high-speed train?