Solution of phototherapy nail polishing step

Illustration of polishing steps of phototherapy nails

Illustration of polishing steps of phototherapy nails. Phototherapy nail art is a new nail art. One of the most commendable advantages is that it is conducive to environmental protection and healthy ingredients. Phototherapy of nails will not produce any irritating smell during the operation. The following is a schematic diagram of the polishing steps of phototherapy manicure.

Schematic diagram of phototherapy nail polishing steps 1 phototherapy nail polishing process

A, suspected glue structure reinforcement of course A program flow (of course A has been repaired):

1, grinding (pay attention to grinding edges and nail grooves in time)

2, special cleaning liquid to clean the nail surface

3. Apply a thin layer of adhesive and bake for 30 seconds.

4. Apply transparent (pink) suspected glue (note that the edges and nail grooves need not be injected) and bake for 2 minutes (the outer edges should be wrapped with suspected glue).

5. Apply sealant, not too thin, and bake for 2 and a half minutes.

6, cleaning liquid cleaning

7. Apply nutritious oil.

B, repair the suspected plastic nail:

1, grinding

2. Mount the patch, and the surface of the patch needs to be carved and polished.

3, cleaning liquid to clean the nail surface

4. Apply adhesive for 30 seconds.

5. Apply transparent (pink) suspected glue for 2 minutes (wrap the outer edge with suspected glue) and polish the nail shape.

6. Apply sealant and bake for 2 minutes.

Step 7 clean up

8. Apply nutritious oil.

C, color suspected plastic nail:

1, grinding.

2. Clean the nail surface with cleaning liquid.

3. Apply adhesive and bake for 30 seconds.

4, paper pad, outer edge and interconnection with transparent glue, baked for 2 minutes, pinched.

5. Dip colorful glue in shell powder paint until the outer edge is "Z" shaped, for 2 minutes.

6. Apply crystal-clear glue to nails and bake for 2 minutes.

7. Polishing, shaping and cleaning the nail surface.

8, apply sealant, phototherapy for 2 minutes and a half, the outer edge needs to be wrapped.

9. Apply nutritious oil. If you need painting and carving, start at the end of step 7.

D. Suspected rubber nails in Europe:

1, disinfection and sterilization

Step 2 remove nail polish

3. Grinding and ash removal

4. Use a special cleaning solution to remove the nail surface, which should be comfortable and clean.

5. Install paper backing plate

6. Wipe the nail surface from the root to the nail edge with a small amount of adhesive to generate chromatography and phototherapy for 30 seconds. Phototherapy can also be the other hand. Too much glue is easy to fall off, you can do four fingers at a time, and you can't clean it after phototherapy.

7. To make the outer edge, use a phototherapy pen to take a small amount of milky white or colored extension glue, from the outside of the fingernail to the left side of the nail edge. These extension adhesives should not be too thick. Take a zigzag shape on the side of the pen, skim off unnecessary suspected glue along the smile line of the extended glue, and phototherapy for 2 minutes. Using technical medical tweezers to bend, it can't be cleaned after phototherapy.

8. Apply the pink extension glue to the nail, and then take it off after the phototherapy pen penetrates into the pink extension glue, and pull out a trace of suspected glue, and connect it to the nail surface that needs to be repaired, so that it can recover after there is liquid on the nail surface, resulting in a smooth plan. Repeat this whole process on other nails, wipe off the suspected glue on the nearby skin and roots with plastic glue to prevent it from falling off, and phototherapy for 2 minutes.

9. Use special cleaning liquid to remove the residual glue, remove the paper pad, let the consumer's hand rotate backwards, and phototherapy the back of the nail 1 min.

10, clean nails, file an idealized wireframe with a white file to remove dust.

1 1. Apply super glue to the nail surface for chromatographic analysis to prevent contact with the skin. Phototherapy lasts two and a half minutes.

12, and use the special cleaning solution to remove the residue again.

13, apply nutrient oil, massage the roots, and the nail surface will be smooth and flawless.

Phototherapy nail polis step figure 2 method/step

Remove the dead skin, push and shovel the dead skin on the edge of the finger with the dead skin, and cut off the shoveled dead skin with the dead skin scissors. Peeling dead skin is the key to doing a good job of phototherapy manicure. Dead skin can't be removed cleanly, and the finished products of phototherapy nails are easy to become warped. )

Manicure, manicure has two positions to be repaired. One is to polish the nail surface. The surface of a person's real nail is smooth and greasy, so it must be polished quickly, otherwise the phototherapy nail will not stick firmly. The second is to cut the front edge of the nail short, and polish the front edge of the nail into an arc that matches the front edge of the paper tray with a grinding strip.

After grinding, use a dust brush to remove dust, and use a cotton pad to clean the nail surface with a certain amount of cleaning liquid.

Apply a small amount of phototherapy primer to the polished nail surface. Apply primer and light the lamp for 3 minutes.

Apply phototherapy glue and use a phototherapy pen to get a proper amount of phototherapy glue. Apply it to nails to make the desired shape and length, put it in a phototherapy lamp for 3 minutes and cure it.

Repeat the fourth step, and the phototherapy glue coated twice is more difficult to fall off.

Apply no-wash sealant, and apply a small amount of sealant on the polished nail surface for 3 minutes. So the phototherapy glue is finished.

Photo nail polishing step Figure 3 Photo nail polishing step

Materials needed for making phototherapy nails

Phototherapy machine, phototherapy kit (adhesive/filler/model glue/super bright seal), detergent, phototherapy pen, phototherapy color glue (pink)

Manufacturing steps of basic phototherapy nails

1. Be sure to get your nails done before you do them. First, roughen the nail surface.

2. Next, polish the "surface" of the nail with a polishing rod to smooth the uneven lines on the nail surface. On the one hand, it can make the mirror effect of phototherapy more flawless, on the other hand, it can remove the grease on the nail surface and make the phototherapy glue stick to the nail more firmly.

3. Then apply a thin layer of glue evenly, and take it out in the phototherapy machine for 30 seconds.

4. Apply pink sequined glue evenly, make two-thirds gradient, and put it into the phototherapy machine for 30 seconds to take it out.

5. Apply model glue, put it into phototherapy machine for 50 seconds and take it out. Then use a pinch of cloth to polish off the sequins, and trim out your favorite A according to your personal preference, and the beautiful phototherapy manicure will be completed.

Note: the adhesive should be applied evenly, and the adhesive and sealing layer adhesive should not be too thick. When applying the adhesive smoothly, don't touch the skin with a pen, and the complete phototherapy nail will be completed.