How to write a good lathe worker training report

First day at work. After meeting in front of the factory next to the 24th floor in the morning. The others scattered and fled. We will meet the difficulties. The lathe worker went! ! After entering the workshop, we have a strong feeling that Tianda is indeed one of the best engineering colleges. Things that look bad can also be used (and generally work well). The windows that look shabby outside are as flexible as the new goods in the dormitory. And because this kind of window is almost never seen before, it adds surprise and freshness. Go to the middle of the workshop, climb the "cupboard table" with all kinds of turning tools and exquisite workpieces, and listen to the teacher's teachings. The first sentence the master said will always be remembered: turning is the most dangerous. I met you as soon as I came up. Therefore, we must pay attention to safety, and girls must wear safety helmets (that is, military training hats). This phone is too scary! Make the flowers look pale, make the grass look twisted, and make every little heart nervous. If the group is divided, it will all be scattered. Ben San and seven other people were lucky enough to get together and follow Master Meng. The master is not tall, but he is round everywhere. Except for the flat head and flat soles, almost all the lines on the whole person are curved. Use a disrespectful metaphor (note: teachers are generally described as disrespectful. But please believe that these teachers have a lot to respect and learn from. Like jujube stones. Unlike most frightened little people (us), the host wears short clothes: T-shirts and sandals. It really relieved us a lot: after all, we can see from the master that he is not afraid. Who are we afraid of with master here? When the master opens his mouth, he speaks Tianjin dialect and is amiable. This has also increased our confidence index. After listening to the introduction of lathe, I assigned a lathe and began to practice shaking table. Three directions, three handwheels. Started the first close contact with the machine tool. I was lucky to be assigned to bed 6 (which started smoothly). It was very easy to use and I spent four happy days with me. 90% satisfaction, weakness is turning tool. In the first 5 minutes, shake it; Five minutes later, run and run. We began to compare the feel of the old and new beds and handwheels. Take a closer look. Well, there are four kinds of eight beds. Although similar, contrast is absolutely necessary. Fortunately, the master followed me for a long time. Let's try it one by one. After about 30 minutes, the real work began! ! ! ! Beautiful! ! First, the master drilled holes and cut materials for the performance. As the first person to eat crabs, I experienced a drill and a cut. Almost effortless. It's a little hard to accept that steel, which is usually considered unattainable, is so easy to process. After that, they distributed materials and went back to their beds to do "private work". Knock the hammer down first. I have experienced the process of rough turning first and then fine turning, squatting on an immobile car cone for half an hour. Our waist and legs passed the test. It's not easy! ! ! It took about two and a half days. Our hammer handle is finished (our group also has two defective products, my pocket type and another classmate's creative type). But they all have something to watch. Please call 1684774474) for specific symptoms. It's all hard work ! ! ! And then enter the real private life time. Each of us should be a part of a vise. The teacher assigned the two most difficult parts to two people who clamored for the simplest part (this distribution method was recognized by everyone) and began to work! ! We have a short time to make every part, but the time limit is very long. So the rest of the time we talked about eating everywhere. From Tianjin to Fujian, I told all the delicious foods in the world. Our tired legs for four days (I won't explain) and our long-suffering intestines (because the smell of engine oil is horrible and we can't eat anything, so our intestines are very painful) have been comforted mentally. Goodbye, Turner! !

Item 2: Forging, welding, milling and planing

On the fifth day, we bid farewell to the already familiar lathe worker. One after another (there should be four) new jobs. Let's forge first. When I walked into the forge classroom, I saw the stove on the wall, the stump on the ground and the anvil on it. I immediately felt the grandeur of Mo Xie, a great machine, and I don't know why there was a fear of Zhou Wang's brand. Plus, the house is too high, and it feels evil. So all the girls want to meet an honest teacher. Cheer up The teacher has a generous face. Have sincere eyes. As soon as I saw him, everyone thought Yang Yang was very warm. In addition, the teacher stuttered a little, which narrowed the distance between him and us (have you seen that ghost stutter? However, if we say it, we can see how much heart the teacher has wasted from the phenomenon that the teacher stutters much less than chatting in class! ! Awe). Class begins first. The temperature of 1300~850 swept away those ghosts. Everyone feels hot yellow molten iron flowing around in front of their eyes. Afraid. Then the teacher lit a big fire, and the imaginary molten iron suddenly turned into a delicious roast duck. These two hours are really a great test of our imagination. Then, air hammers and stamping devices of various specifications were started in turn, which made people feel that thunder rumbled and guns burst, without exception. When the biggest air hammer starts: it is vibrating, the wall is vibrating, the ground is vibrating, and our hearts are vibrating. At that moment, there was only one thought in my mind: Is our foundation solid enough? ! This feeling is like going through the baptism of a horror movie (don't laugh, I have never seen the world. Because the machines in the real factory are much scarier than this one. Of course, there will be times when the bitter comes the sweet. We're going to strike the iron soon! ! A round iron burns in a small stove. All we have to do is swing a sledgehammer and try our best to chisel it into a square! We all became little blacksmiths in Milan, tinkling. This is really easier said than done. If the hammer swings high, it can't be hit; If you swing low, you won't hit deep. It's been smashed all morning, and one of them has the meaning of a square. In the afternoon, under the pressure of the air hammer, our small square became a small square in the first few seconds. Looking at the master's performance, we only have admiration in our hearts. I experienced the process of taking out a stick from the high-temperature furnace and smashing it on the air hammer over and over again in the afternoon (I practiced my courage because I was watched by the master, but I was desperate without the master). Our admiration for teachers has been upgraded to worship. Who says workers are incompetent? If you have the ability, you can strike the iron within three tempering! Still smashed! I scared you to death! !

Day six. Let's go welding. The first time in the morning was even scarier. I took classes all morning. I knew something was coming, and the wind cast a shadow in front of it. Sure enough. Wear a mask and arc weld yourself as soon as you get up in the afternoon! ! I don't need to elaborate on this fear. It's enough for me to play with the protective glass that can only see the super bright arc on the mask. Because my arc welding is not in a straight line at all (it's all solder joints, you can experience it yourself), so I won't say much (hehe, don't hit me). I said gas welding. Gas welding is more dynamic than arc welding. Because arc welding has at least masks and gloves, and gas welding is not allowed at all! ! You must melt the slices first, and then add covered electrode to them. Every time I add it, there are colorful sparks flying. It's really unbearable! ! ! Fortunately, I have been ironed once as a lathe worker, and I don't care about this second meeting. It is worth winning a compliment from the teacher! ! ! But the most puzzling thing is that such a dangerous job is actually a female teacher! ! ! Really! Before leaving work in the afternoon, we listened to the introduction of stamping again. I really think workers are too dangerous! Pay tribute to the master worker! ! !

Days 7 and 8. What a grind! I thought the so-called milling worker was done in a medium with water. It won't be like that when you get there! ! ! Also sharp tools and similar lathes. But the difference is that a lathe worker is a knife and a milling worker is a piece. You can also process planes. Ben: Because the things we process will be used by ourselves in the future, we have finely ground the parts, and all the parts have reached the accuracy of 120%. Pray for good luck! ! !