Ask Sony Sony VPL-CX6 Manual ~ ~ Before 0: 00 on July 5th ~

Advantages: The appearance of this machine is the same as CX-5, which is fashionable and concise. It has the functions of automatically opening the lens cover, automatically adjusting the projection height and electric tilt adjustment, and automatically adjusting the projection angle to the angle when it was used last time. It is very practical to recognize and adjust the projection angle and automatically correct the trapezoidal distortion of the picture. The design is more humanized.

It seems useless up there.

Instructions before use

Safety instructions

1 Please check whether the working voltage of this machine is consistent with the local power supply voltage.

If liquid or solid falls into the casing, please unplug the power plug of the machine and ask professional technicians to check it before using it.

When the machine is not used for several days, please unplug it from the wall outlet.

4 When unplugging the power cord, please hold the plug and pull it out. Never pull the wire itself.

5. The power socket on the wall should be close to the machine and dry wired.

Even if the power supply of this machine is turned off, as long as its plug is connected to the power socket on the wall, this machine will not be separated from the AC power supply.

Don't look directly at the camera when projection lamp is turned on.

8 Don't put your hands or articles near the ventilation holes. Because the discharged air is very hot.

9 Be careful not to be caught by the regulator. When the power supply is turned on, the power inclination adjuster of this machine will automatically extend out and retract when the power supply is turned off. Do not touch this machine when the regulator is running. After the automatic operation of the electric tilt adjuster is completed, make fine adjustment.

10 Please don't put cloth or paper under the machine.

Lighting instructions

1 In order to get the best image, the front of the screen should not be exposed to direct light or sunlight.

It is recommended to use lifting fluorescent lamps. Please cover the fluorescent lamp with a lampshade to avoid reducing the contrast.

Cover all windows facing the screen with opaque curtains.

It is best to install the projector in a room where the floor and walls are not made of reflective materials. If the floor and walls are reflective materials, it is best to change carpets and wallpaper into dark colors.

Preventive measures for internal heat accumulation

The projector has ventilation (air intake) holes and ventilation (air exhaust) holes. Do not block these holes or place anything near them, otherwise internal heat accumulation may occur, which may lead to image quality degradation or projector damage.

Cleaning instructions

1 In order to make the cabinet look brand-new, please clean it regularly with a soft cloth. Stubborn stains can be wiped off with a cloth dipped in neutral detergent. Do not use strong solvents such as thinner, gasoline or polishing agent, otherwise it will damage the shell.

Don't touch the camera. Please wipe the dust off the lens with a soft dry cloth. Do not use wet cloth, detergent or thinner.

Please clean the filter regularly.

About LCD data projector

The LCD data projector is manufactured with high precision technology. However, you may find some small black spots and/or bright spots (red, blue or green) on the LCD data projector. This is a normal result in the manufacturing process, not a fault.

Improper installation

Please do not install the projector in the following places. Otherwise, the projector may fail or be damaged.

Poor ventilation

1 Ensure good ventilation and avoid internal heat accumulation. Do not put this machine on the surface (carpet, blanket, etc.). ) or nearby items (curtains, curtains, etc. ) may block the vent. When the internal heat is accumulated due to blockage, the temperature sensor will send out "Working temperature is too high! /kloc-turn off the lights after 0/minute. " 1 minute, the power will automatically turn off.

Leave more than 30 cm of space around the machine.

3 Pay attention to the possibility that small objects, such as paper scraps, may be sucked into the ventilation holes.

High temperature and humidity

1 Do not install this machine in a place with extremely high or low temperature or humidity.

To avoid water vapor condensation, do not install this machine in a place where the temperature may rise rapidly.

Please do not install this machine in a dusty place, or it will block the air filter. Dust will prevent air from penetrating through the filter, which may lead to an increase in heat inside the projector. Please clean the air filter regularly.

Uncomfortable environment

Do not use the projector under the following conditions.

Dumper

Do not use this machine when it is upside down. Otherwise, it may lead to failure.

Tilt the machine beyond the range set by the regulator.

Do not use the machine when it is tilted beyond the range set by the regulator. This installation method may lead to color shadow or greatly shorten the life of the projector lamp.

Tilt the machine to the right or left.

Do not tilt the machine at an angle of 15 degrees, and do not install the machine in any other way unless it is placed on the floor or hung from the ceiling. This installation may lead to colored shadows or greatly shorten the life of projection lamp.

Blocking ventilation hole

Do not cover the vent (exhaust/air inlet) with articles; Otherwise, internal heat will accumulate.

For more information about the vent (air intake/exhaust), please refer to "Location and function of the controller" on page 8.

1 power saving indicator

Lights when the projector is in power saving mode. When the "power saving mode" item in the operation setting menu is set to "On", if there is no signal input for 10 minutes, the projector will enter the power saving mode. Projection lamp goes out, but the cooling fan will continue to rotate. When a signal is input or any key is pressed, the power saving mode is released. In power-saving mode, after the projection lamp is turned off, any key will not work for the first 60 seconds.

2 menu key

A display menu for display that screen. Press the key again when you want to cancel the menu.

4 Enter key

Used to input the setting values of items in the menu system.

5 Temperature/Fan Indicator

The light is on or flashing when:

When the internal temperature of the projector is abnormally high, (1) lights up.

(2) Flashing when the fan is damaged.

For more information about the temperature/fan indicator, see page 44.

6 light (projection light)/cover indicator light

The light is on or flashing when:

(1) The projector lamp is reused or lit at high temperature.

(2) Flashing when the lamp cover or air cleaner cover is not installed tightly.

See page 44 for more information about the light/cover indicator.

Connector panel

1 input a connector (hd d pair 15 core, female)

Connect to an external device such as a computer.

Connect the monitor output port on the computer with the attached cable. When inputting component signals or 15k rgb signals, please use the optional cable.

For details, see "Connecting 15k rgb/ component devices" on page 19.

Two usb connectors (upstream usb plug, 4 cores) are connected to the usb connector of the computer. When connecting the projector to the computer, you can control the mouse function with the included remote control. (When you use the vpl-exl model, you need to use the optional remote control to control the mouse function of the remote control. Connected application software (vpl-cx6 model only) can be installed on the computer connected to this connector.

3 Memory slot (VPL-cx6 model only)

The memory module can be inserted. Do not insert anything other than the memory stick.

For more information, please refer to the attached "Operating Instructions" about the memory stick.

4 audio (stereo mini jack) connectors

When listening to the sound output from the computer, please connect the audio output from the computer.

Connect the audio output of the video recorder when listening to the audio output of the video recorder.

5 service lights (VPL-cx6 model only)

In the process of accessing the memory stick, this light comes on.

Do not take out the memory stick when the channel light is on.

6 video input interface

Connect to an external video device such as a video recorder.

(1) video (shielding): Connect the composite video output port of video equipment.

(2) S video (mini din 4 core): connected to the S video output (y/c video output) port of video equipment.

7 AC input (AC input) socket

Used to connect the supplied AC power cord.

remote control

The remote control buttons with the same name as the buttons on the control panel have the same function.

About vpl-cs6/vpl-cx6 model

2 apa (automatic pixel correction) key

When the signal is input from the computer, it is used to automatically adjust the image to be projected to the clearest. This key is used when "Smart apa" in the operation setting menu is set to "Off". Usually set to "On".

When the complete image is displayed on the screen, press the apa key. If there is a black border around the image, the apa function will not work properly and the image may exceed the screen.

(1) When "Adjust" appears on the screen, press the apa key again to cancel the adjustment.

(2) Depending on the type of input signal, the image may not be adjusted correctly.

(3) When manually adjusting the image, please adjust the items of Point Phase, Dimension H and Offset in the input setting menu.

3 pic mute key

Used to temporarily weaken the tone of the image. Press this key again to restore the image.

4 Enter key

These keys imitate mice.

These keys have the same function as the mouse keys of a computer connected to the projector through a usb cable.

A)l click key (back): it plays the role of the left mouse button.

B) joystick

C)r click key: play the role of the right mouse button.

Only when the projector is connected to the computer with a usb cable, the functions of these keys are the same as those of the mouse keys of the computer.

For more information, please refer to "Controlling the Computer with the Attached Remote Control" on page 24.

6 function1,2 key (VPL—-cx6 model only)

When connecting the projector to the computer, just press the function key to open the file on the screen. This will enhance your publishing effect. To use this function, use the attached application software to assign files to function keys.

For more information, please refer to the readme file and help file of the application program.

Connect the computer to the projector with usb cable and activate the function key.

For more information, see "Connecting an ibm pc/at Compatible Computer" on page 17.

7 reset key

Used to restore the value of the project to its factory preset value, or to restore the enlarged image to its original size. This key works when a menu or setting item is displayed on the screen.

10 menu key

12 enter key

13 freeze key

Used to fix the projected image. When you want to unpin the image, press this key again.

14 ms slide rail (ms key (only applicable to vpl-cx6 model)

Used to show slides. When the input signal is non-millisecond, it will be switched to millisecond ... To start the slide show, please press this key again.

15 infrared transmitter

Install the battery

1 Press and push the battery cover, and then install two aa (r6) batteries with correct polarity (attached).

2 Replace the battery cover.

Applicable to vpl-ex 1 model.

3 menu key

5 infrared emitter

6 freeze key

Used to fix the projected image. When you want to unpin the image, press this key again.

7 Enter key

8 apt (automatic pixel correction) key

When the signal is input from the computer, it is used to automatically adjust the image to the clearest. This key is used when "Smart apa" in the operation setting menu is set to "Off". Usually set to "On".

9 d keystone (digital adjustment trapezoidal distortion) key

10 reset key

Used to restore the value of the project to its factory preset value, or to restore the enlarged image to its original size. This key only works when the menu or setting item is displayed on the screen.

Precautions before using the remote control

Please remove the transparent film from the lithium battery bracket.

To replace the battery

1 Remove the lithium battery holder to unlock it, and then remove the holder from the remote control.

2 Install the lithium battery.

3 Put the lithium battery bracket back to the remote control.

Matters needing attention of lithium battery

1 Keep the battery out of the reach of children.

If the battery is swallowed, you should go to the hospital immediately.

Matters needing attention in remote control operation

1 Make sure that nothing blocks the infrared beam between the remote control and the remote control detector on the projector. Please point the remote control directly at the remote control detector in front or behind.

The effective working range is limited. The shorter the distance between the remote controller and the projector, the wider the angle at which the remote controller can control the projector.

project

1 Open the connector panel, plug the AC power cord into the wall socket, and then connect all devices.

The on/standby indicator lights up in red, and the projector enters the standby state.

When the projector is turned on, the startup screen will pop up (vpl-cx6 model only). For more information about the startup screen, please refer to the attached "Operating Instructions for Memory Stick".

4 Press the Enter key to select the input source.

Intelligent apa (Automatic Pixel Adjustment) adjusts the image of the connected device so that it can be projected clearly.

1 If "Automatic Input Search" is set to "On", the projector will search for signals from connected devices and display the found input channels of input signals.

For details, please refer to "Automatic Input Search" in the operation setting menu on page 35.

Intelligent apa is only valid for input signals from the computer.

For more information about the tilt adjustment key, please refer to "How to use the electric tilt adjuster" on page 9.

When the tilt key is used to adjust the electric tilt adjuster, automatic keystone distortion correction adjustment will be performed at the same time. If you do not want to perform automatic keystone correction, set the vertical keystone correction menu to manual. (See page 37. )

6 Rotate the zoom ring to resize the image.

7 Turn the focus ring to adjust the focal length.

Looking directly at the camera when projecting may hurt your eyes.

To switch from intelligent automatic setting function to manual adjustment, you can use the menu to switch the following functions from intelligent automatic setting to manual adjustment.

1 Vertical keystone distortion correction (keystone distortion correction)

Set the "Vertical Trapezoidal Distortion Correction" item in the installation setting menu to "Manual".

2 intelligent apa (automatic pixel adjustment)

Set "Smart apa" in the operation setting menu to "Off".

3 automatic input search

Set "Automatic Input Search" in the operation setting menu to "Off".

For more information about menu operations, see "Using Menus" on page 30.

modulate the sound

You can adjust the volume in the on-screen menu. See "Volume" in the image setting menu on page 32.

Temporarily reduce the image tone (only applicable to vpl-cs6/cx6 models)

Press the pic mute button on the remote control. Press the key again to restore the image.

Use the included remote control to control the computer.

When the ibm pc/at compatible computer is connected to the projector through usb cable, the computer mouse can be controlled through the remote controller.

The functions of the p/l click key and joystick are as follows:

For more information about usb connectors, see "Connecting an ibm pc/at Compatible Computer" on page 17.

Make sure that nothing blocks the infrared beam between the remote control and the remote control detector on the projector.

Use a safety lock

1 Please press the menu key on the installation setting menu, and then turn on the "Security Lock" setting.

2 Enter the password.

Then, the screen for entering the new password is displayed. (Even if you want to save the current password, please enter the password on this screen. )

3 Enter the password again to confirm.

If an incorrect password is entered, the message "Invalid password" will be displayed on the menu screen.

4 The security lock has been completed.

1 If you forget your password and the password manager is invalid, you will not be able to use the projector. In this case, it should be recognized that security locks can also prevent effective use. It is recommended that you record the selected password.

If you call the after-sales service center because you forgot your password, you need to check the serial number of the projector and your identity. (In other countries, this procedure may be different. Once your identity is confirmed, we will provide you with a password.

Power off

3 After the fan stops running and the on/standby indicator is red, unplug the AC power cord from the wall socket.

Do not unplug the AC power cord while the fan is still running; Otherwise, even if the internal heat is high, the fan will stop running, which may damage the projector.

Air filter screen description

Please clean the air filter every 300 hours in order to keep the best working condition. See "Clean Air Screen" on page 40 for details.

Use menu

The projector is equipped with on-screen display menu, which can make various adjustments and settings. Set the items to be displayed in the pop-up menu or drop-down menu. If you select an item name with a dot (…), a drop-down menu with setting items will appear. You can change the color of the menu display and the language in which the menu is displayed on the screen.

To change the menu language, see "Selecting a Menu Language" on page 20.

Show items

Input signal indicator lamp

Input signal indicator lamp

Input signal setting indicator light

Input A: Display "Computer", "Component" or "Video Signal Input gbr".

Input Video /s Video: Display the setting of "Auto" or "Color System" in the operation setting menu.

1 Press the menu key.

Menu display.

The currently selected menu displays a yellow button.

4 Set or adjust a project.

When setting the menu language, please refer to "Selecting a Menu Language" on page 20.

Cancel menu

Press the menu key.

If you don't press the key within 1 minute, the menu will be cancelled automatically.

To restore the settings of an adjusted item

Press the reset button on the remote control.

"over!" Appears on the screen, and the various settings that appear on the screen are restored to the factory default values.

The recoverable items are:

1 Adjust the contrast, brightness, color, hue, sharpness and enhance rgb in the image … menu.

2 Adjust the signals in the menu … "Point Phase", "Size H" and "Shift".

On the storage of set values

The setting value is automatically stored in the memory of the projector.

When there is no signal input

If there is no signal input, "This item cannot be adjusted" will appear on the screen.

About menu display

You can set the display position of the menu, the brightness of the background image and the tone of the menu item according to your own preferences.

See "Menu Settings" on page 36 for details.

Image setup menu

The image setting menu is used to adjust the image or sound.

According to the input signal, items that cannot be adjusted in the menu will not be displayed.

For more information about nonadjustable items, see page 49.

menuitem

Image mode

Select the image mode.

Dynamic: emphasize contrast to produce an "ecological" image.

Standard: This setting is usually selected. If the image feels rough when "Dynamic" is set, this setting can reduce this rough feeling.

roll

Adjust the sound

Adjust image ... menu item

For each "dynamic" or "standard" image mode, the machine can store the setting values of the following drop-down menu items respectively.

Adjust the image ...

When a video signal is input

When an rgb signal is input,

contrast

Adjust the image contrast. The higher the setting value, the greater the contrast between the dark and bright parts of the image. The lower the setting, the smaller the contrast.

clever

Adjust the brightness of the image. The higher the setting value, the brighter the image. The lower the setting, the darker the image.

colour

Adjust the color density. The higher the set value, the greater the concentration. The lower the set value, the smaller the concentration.

colour

Adjust the hue. The higher the setting value, the greener the image. The lower the setting value, the more purple the image is.

acutance

Select image sharpness from high, medium and low. The setting value of "high position" makes the image vivid; The "Low" setting softens it.

Enhanced rgb

Adjust the image definition when rgb signals are input.

The higher the setting value, the clearer the image. The lower the setting, the softer the image.

Gamma model

Select the gamma correction curve.

Picture: Improve the reproduction effect of midtones. Photos can be reproduced in natural tones.

Text: Enhance the contrast between black and white. Suitable for images with more words.

colour temperature

Adjust the color temperature.

High position: make white and blue.

Low position: make white reddish.

Input settings menu

The input setting menu is used to adjust the input signal.

According to the input signal, items that cannot be adjusted in the menu will not be displayed.

For more information about nonadjustable items, see page 49.

When a video signal is input

When an rgb signal is input,

menuitem

Wide mode

Sets the aspect ratio of the image. Set to ON when16: 9 (compressed) signal is input from dvd player and other devices.

Off: When an image with an aspect ratio of 4: 3 is input.

On: When inputting an image with an aspect ratio of16: 9 (compressed).

Adjustment signal … menu item (only when rgb signal is input)

Point phase

Adjust the point phase of LCD panel and computer output signal.

Press the apa key to adjust the image, and then further adjust it to get a clearer image.

Adjust the image to the clearest.

Dimension h

Adjust the horizontal size of the output image of the connector. The higher the setting value, the larger the horizontal size of the image. The lower the setting value, the smaller the horizontal size of the image. Please adjust the setting value according to the number of points of the input signal.

Please refer to page 50 for a detailed description of the appropriate values of preset signals.

change

Adjust the position of the image. H adjust the horizontal position of the image. V Adjust the vertical position of the image. With the increase of h setting value, the image moves to the right; As the set value decreases, the image moves to the left.

Scanning converter

Convert the signal according to the screen size to display the image.

On: Displays the image according to the screen size. The clarity of that image will be reduce.

Off: Displays the image when the input image signal matches the pixels of the LCD screen. The image is clear, but the image size will be smaller.

1 When xga, sxga or sxga signals are input, this item will not be displayed (vpl-cx6/exl models).

2 When svga or xga signals are input, this item will not be displayed (vpl-cs6 model).

About the preset storage quantity

This projector connector has 38 kinds of input signals (suitable for vpl-cx6/exl models) and 25 kinds of preset data (preset memory). When the preset signal is input, the projector automatically detects the signal type and calls the data of the signal from the preset memory to adjust the signal to obtain the best image. The storage number and signal type of the signal are displayed in the information menu (see page 38). It can also be

Enter the setting menu to adjust the preset data.

The projector also has 20 kinds of user storage for the input -a connector, which can store setting values of adjustment data of non-preset input signals.

When the non-preset signal is input for the first time, the storage number is displayed as 0. If the signal data is adjusted in the input setting menu, it will be registered in the projector. If more than 20 logged-in users are stored, the latest stored value will automatically replace the oldest value.

Please refer to the table on page 50 to find out whether the signal has been registered in the preset memory.

Because the data of the following signals are called from the preset memory, these preset data can be used by adjusting the "size h" item. Fine-tune by adjusting the "shift" item.

When the aspect ratio of the input signal is not 4∶3, some pictures are displayed in black.

Damn, I'm so fucking tired ... there's still so much ... remember to add points.

Operation setting menu

The Operation Settings menu is used to change the operation settings of the projector.

Intelligent apa

Activate or deactivate the intelligent apa 1).

On: This setting is usually selected. When the signal is input from the computer, apa automatically executes so that the image can be clearly seen. Once the intelligent apa adjusts the specified input signal, it will not be readjusted even if the cable is disconnected and the input channel is reconnected or changed. Even if smart apa is set to ON, you can adjust the image by pressing the apa key on the remote control.

Off: When you press the apa key on the remote control, apa starts to work.

1) For the input signal from the computer, apa (Automatic Pixel Adjustment) will automatically adjust "Point Phase", "Size H" and "Offset" in the input setting menu.

Automatic input search

Usually set to "Off".

When set to "On", the projector detects input signals in the following order: input a/ms (only applicable to vpl-cx6 models)/video /s video. When the power is turned on or the enter key is pressed, the input channel will be displayed.

Input signal selection

Select the computer, component or video gbr signal input through the input A interface.

If the setting is incorrect, the image color will become abnormal or "Please confirm the input of setting A" will appear on the screen, and the image will not be displayed.

color system

Select the color system of the input signal.

If "Automatic" is selected, the projector will automatically detect the color system of the input signal. If the image is distorted or colorless, please select the color system according to the input signal.

Power saving mode

When set to "On", the projector will enter the power-saving mode if the machine is not operated for 10 minutes without signal input.

infrared detector

Select the remote detectors (infrared receivers) in front of and behind the projector.

Front or rear: Both front and rear detectors are activated.

Front: Only the front detector is activated.

Rear: Only the rear detector is activated.

explain

Select whether the sony logo on the back of the projector lights up when the projector is turned on. Usually this setting is on. If you want it to be completely black or think this setting is unnecessary, please change this setting to "Off".

Menu settings

Menu Settings Menu is used to change the operation settings of the projector.

menuitem

Status (screen display)

Set the screen display status.

On: Displays all screen display contents.

Turn off: Turn off all screen displays except menus, information when power is turned off and warning information.

language

Select the language used for menu and screen display. Available languages are: English, Dutch, French, Italian, German, Spanish, Portuguese, Russian, Swedish, Norwegian, Japanese, Chinese and Korean.

Menu position

Select the display position of the menu from top left, bottom left, middle, top right and bottom right.

Menu color

Select the hue of the menu display from black or white.

Set menu

The Installation Settings menu is used to change the installation settings of the projector.

menuitem

slanting ...

Vertical trapezoidal distortion correction

Depending on the temperature of the room or the angle of the screen, automatic vertical keystone distortion correction may not completely correct keystone distortion.

Flip the image

Flip the image on the screen horizontally and/or vertically.

Off: The image cannot be flipped.

Hv: Flip the image horizontally and vertically.

H: Flip the image horizontally.

V: Flip the image vertically.

When the image flip is set to "hv" or "V", projection lamp works at the "standard" setting.

background

Select the screen background color when there is no signal input from the projector. Choose black or blue.

Usually set to "blue".

Photographic lamp mode

Sets the brightness of the projection lamp in the projection.

High position: Brightly illuminate the projected image.

Standard: Reduce fan noise and power consumption. The brightness of the projected image is lower than that when "High Position" is set.

High altitude model

Off: Use this setting when using the projector at normal height.

On: Use this setting when using the projector at an altitude of 1500 m or higher.

safety lock

Turn on the projector's security lock function.

Off: Turn off the safety lock function.

On: Turn on the safety lock function. Once the password is set, the projector will be locked.

For more information, see "Using Security Locks" on page 25.

P.s plus points! ! ! ! !

I searched for 2 hours and found an address from the source code. ...

There are many pictures that can't be displayed. I can't help it sorry

And "maintenance" I don't care. ...

Hehe, I wish you a smooth use.