Traditional Culture Encyclopedia - Photography and portraiture - Xiangyun torch can withstand several strong winds and will not go out.
Xiangyun torch can withstand several strong winds and will not go out.
The torch of Beijing Olympic Games is 72 cm long and weighs 985 grams. Combustion time15min, flame height 25-30 cm at zero wind speed. It can be recognized and photographed in strong light and sunlight. In terms of technology, one-step forming technology of conical surface and aluminum etching coloring technology are adopted. The fuel is propane, which meets the requirements of environmental protection. The torch shape is made of recyclable and environmentally friendly materials. The internal combustion system of the torch is to install a set of equipment inside the torch, so that the torch can keep burning in a certain range of complex environment for a period of time after being ignited, and complete the relay transmission. Academician Liu Xingzhou said that the internal combustion system of the torch of the Beijing Olympic Games consists of three parts: burner, pressure stabilizing device and gas storage tank. "We just need to carefully install and fix these devices in a small, curved and irregular space." Propane was chosen as the torch of Beijing Olympic Games. Propane mainly produces water vapor and carbon dioxide after combustion, which will not pollute the environment. More importantly, propane can adapt to a wide temperature range, and it can still produce a saturated vapor pressure above 1 at MINUS 40 degrees Celsius, which is higher than the external atmospheric pressure and forms combustion; Moreover, the flame produced by propane is bright yellow, and when torchbearers run, the dynamic fluttering flame is more eye-catching in different backgrounds. An important innovation of the torch internal combustion system of Beijing Olympic Games is to set up a "double flame" scheme. Academician Liu Xingzhou said that after the gas flows out, part of it enters the main combustion chamber of the burner, forming a relatively full flame outside the torch. The other part enters the precombustion chamber and keeps a relatively small but very stable flame in the torch. If extreme conditions occur, the flame in the main combustion chamber goes out, and the pre-combustion chamber can still keep burning, so as to ensure that the torch will not go out. Angel's Wings Answer Time 2008-06-05 10:20 The creative inspiration of the torch of Beijing 2008 Olympic Games comes from the "auspicious clouds" pattern of "symbiosis and harmony". The cultural concept of Xiangyun has a time span of several thousand years in China, and it is a representative cultural symbol of China. The design of the torch was inspired by the traditional paper roll in China. Paper is one of the four great inventions in China and spread to the west through the Silk Road. Human civilization spread with the appearance of paper. The application of lacquer red, which originated in the Han Dynasty, on the torch makes it obviously different from the torch design of previous Olympic Games. The contrasting colors of red and silver produce striking visual effects, which is beneficial to various forms of media communication. The torch is divided into upper and lower parts, the auspicious cloud pattern and the three-dimensional relief process design make the whole torch elegant and gorgeous, with rich connotations. The torch of Beijing Olympic Games is 72 cm long and weighs 985 grams. Combustion time15min, flame height 25-30 cm at zero wind speed. It can be recognized and photographed in strong light and sunlight. In terms of technology, one-step forming technology of conical surface and aluminum etching coloring technology are adopted. The fuel is propane, which meets the requirements of environmental protection. The torch shape is made of recyclable and environmentally friendly materials. The torch of Beijing Olympic Games has reached a new technical height in terms of combustion stability and adaptability to the external environment, and it can keep burning under the conditions of strong wind with a speed of 65 kilometers per hour and 50 mm rainstorm. In terms of technology, it is designed with light and high-quality aluminum alloy and hollow plastic parts, which is very lightweight. The lower part is sprayed with high-touch plastic paint, which feels comfortable and is not easy to slip. The torch of Beijing Olympic Games is a product independently designed and developed by China, which has complete intellectual property rights. The fuel used for the torch of the Beijing Olympic Games is propane, which is a low-cost common fuel. Its main components are carbon and hydrogen. After burning, there are only carbon dioxide and water, and there are no other substances, which will not pollute the environment. Aerospace core, that is, the combustion system of the torch for the 2008 Beijing Olympic Games, includes two parts: fuel supply system (fuel bottle, pressure stabilizing device and heat storage device) and burner. When working, the switch tool opens the normally closed switch valve on the fuel bottle clockwise. The high-pressure propane vapor in the bottle is depressurized by the pressure stabilizing device and maintained at a relatively stable pressure value, and then enters the regenerative copper tube through the side hole of the fuel distributor with five air holes, flows through the combustion chamber and the fuel bottle, re-enters the fuel distributor, and enters the precombustion chamber and the main combustion chamber from two paths for combustion respectively. The main components of the fuel supply system for fuel bottle are pressure stabilizing device and fuel bottle, which are independently developed by adopting domestic advanced technology and technology. The fuel bottle adopts seamless cold-drawing technology, with a diameter of 32 mm, that is, it is drawn into its present shape by a whole piece of plate, so it is very resistant to pressure (up to 14 MPa), which is equivalent to bearing the pressure above 1400 meters underwater. Due to the time requirement of torch burning, a bottle of fuel needs to burn for more than 15 minutes. Besides the torch shape, the burner also has certain flow requirements. Therefore, in order to ensure the matching with the torch shell and meet the burning time, the fuel bottle can only be made thin and long. This is technically more difficult. Because it is integrally formed, and the wall thickness of the fuel bottle wall is less than 1 mm, it is easy to crack when the slenderness ratio reaches 7.5 times. The choice of fuel is propane with purity over 99%. Historically, the Olympic torch has used more mixed fuel. Propane fuel is used to meet the environmental temperature requirements in the torch relay route. Secondly, color is also a consideration. After propane burns, the flame is orange and the visibility is good. The voltage stabilizing device is also specially developed. The pressure of the gas coming out of the fuel bottle is unstable and decreases with the decrease of temperature. The combustion of the torch needs a stable flow, and the function of the regulator is to provide fuel supply with a certain pressure and flow, which is the same as the principle of the general regulator. The gas fuel enters the inlet of the pressure stabilizing device at a higher pressure and flows out at a pressure higher than the ambient pressure in a certain range to ensure the fuel pressure and flow required for combustion. The design requirements of voltage regulators are usually small, light and multifunctional. The current voltage stabilizing device has four functions: first, the flashlight switch is designed on the voltage stabilizing device, and the voltage stabilizing device is missing a part; The second is decompression; The third is voltage stabilization; The fourth is to ensure that the torch continues to burn without danger in the event of accidental fall. Connection of fuel bottle and pressure stabilizing device The fuel bottle and pressure stabilizing device are connected by threads, and the fuel bottle mouth has external threads, and the pressure stabilizing device has internal threads. Although this is not original, it is rarely used in the torch. In the past, some torches used ready-made fuel bottles, and most of them used direct jacking. If the air pressure is too high, the thimble will be pushed tightly and it will be difficult to use. If the pressure is too small, it is easy to loosen due to vibration during use, resulting in air leakage; At the same time, due to inaccurate positioning and sealing, it is easy to leak due to lax sealing during compaction or use, which is neither safe nor easy to extinguish. We have learned the experience and lessons of foreign torches and adopted a threaded interface. Both the 2000 Sydney Olympic Games and the 2002 Salt Lake City Winter Olympics torches used heat preservation devices. Because for gas phase combustion, if there is no effective heat supplement, the temperature of the fuel bottle will drop. When the fuel is at low temperature, the steam pressure will decrease, which may affect the combustion performance of the torch. The original design encountered this problem. When it was first developed, the fuel bottle was bulky, so it cooled slowly. Now the fuel bottle is smaller, the burning time is longer, and the thermal device needs to be added back. To heat, there must be a heat source, so it is natural to use the flame heat of the torch itself-the fuel does not directly enter the combustion chamber after it comes out, but heats the fuel bottle through the heat storage system to slow down the cooling speed and meet the combustion time. Another advantage of the regenerative tube is that it is impossible to exchange all the heat through heat exchange, so the temperature of the gas in the tube is also increased, which is beneficial to combustion, which is an additional benefit. The burner is designed with double flames as the core, which is used for the first time in China. After heat storage, the fuel oil is divided into two paths, one of which enters the precombustion chamber and the other enters the main combustion chamber, and is basically distributed according to the ratio of 1:2. The center of the bottom of the precombustion chamber is a nozzle, and the periphery is an air inlet. There is also an air inlet channel with a certain area at the bottom of the torch shell. When the fuel in the precombustion chamber is injected upward, it will drive the surrounding air to rise and enter the precombustion chamber, which is the injection effect. The fuel and air in the precombustion chamber are mixed and then burned. Just like our gas stove, the flame is well mixed and burned fully. The flame has high temperature, short shape and blue color, which is not easy to see under strong light. However, the fuel in the main combustion chamber is not premixed, and it is mixed with air after being sprayed out, and then diffused and burned, and the flame temperature is slightly lower and it is opaque orange. The flame height is higher than 25 cm. The precombustion chamber is equivalent to a stable fire source, ensuring that it will never go out. Even if the flame of the outer main combustion chamber goes out, the main flame will be ignited immediately. There are similar designs of double flames abroad, but they are not the same, and they are not premixed. Like the 2006 Winter Olympics in Turin, there are also two combustion chambers, but both are diffusion flames. We consider using premixed flame, mainly because its temperature is higher and it is easier to reignite the main flame. On the other hand, the main flame is above and the pre-combustion flame is below, which is relatively less affected by the outside world and is easier to protect the flame. Our design is actually inspired by the air-breathing engine. Because some engines also have a small precombustion chamber. It should be said that this scheme is the first time in the use of the torch. It is also very special that the main flame is ejected from the uniform holes in the circular tube. Many foreign countries use small nozzles, or although there are multiple nozzles, the size is relatively large. We have also done experiments on this scheme. On the one hand, it is not conducive to the stability of the flame, on the other hand, it has a large smoke when burning. In our current design, the flame can be ejected from the small hole of a ring. One of the advantages is that the ejected fuel is relatively uniform and is a circular flame; The other is that the sprayed fuel can be mixed with air more evenly, and the smoke will be small when it is fully burned, which is beneficial to viewing and environmental protection. During the development of the torch, we found that the wind speed has the greatest influence on the torch's work, and a lot of experiments were carried out on special equipment to ensure that the torch will not stall under strong winds and small winds. We really hope to get a flashlight with reliable and stable performance. We believe that we should continue to evaluate the torch parameters in the actual environment in the future and ensure the development quality through strict production processes. We expect the Beijing Olympic torch to spread the same dream in the same world.
Please accept it, thank you!
- Previous article:The most beautiful Datong Tik Tok photo contest
- Next article:Can I bring pets on Taohua Island in Gan County?
- Related articles
- Island photography skills
- Nanjing Institute of Art fractional line
- What are the balls on both sides of Yuzhu joint?
- Untitled photography Gordon Underwood
- How to choose delicious crabs? Simple 4 tricks teach you to choose fresh crabs.
- Hongye wedding photography
- Esther was photographed by a photographer.
- What are the flower viewing strategies in Chengdu in March 2022?
- What competition did Alice have with the Queen?
- Why is it not recommended to visit Humble Administrator's Garden when traveling to Suzhou, a paradise on earth?