How to set the flasher?

Question 1: How to set up a 5-point camera when using a SLR camera with a flasher? Adjust the shutter, tripod and ISO values you want, and then manually adjust the output power and flashing distance of the flash. If the maximum power of the flash can't meet your needs, change the camera parameters. For example, improve ISO.

Question 2: How to use the flasher? Generally, flash lamps are divided into TX and RX, where TX is placed on the hot boots of the camera and RX is placed on the flash lamp. If TX and RX are installed backwards, it will lead to no flashing, and WFC-0 1 flasher is integrated with receiving and sending, so this will not happen. Maybe it's the channel setting. In the use of flasher, channel setting is very important. For example, two flashers should have the same channel. As long as the channel is set correctly, there is generally no unavailability.

Question 3: How to set the Kimbe TR-A4 flasher? The main consideration is flash synchronization. At this time, the shutter priority mode is used, and the shutter speed is generally 125 seconds. A better flash can last 200 seconds. Take a pat and you'll know if it's synchronized.

Question 4: How does the studio adjust the flash trigger between the light box and the flasher to make them interfere with each other? The only solution is to find a way from the trigger principle.

There are two kinds of flashing lights to trigger * * *, light and wireless.

If you can't see between the two sheds, there will be no lights flashing.

Even if a room is divided into two rooms, as long as the middle partition is relatively sealed, that is, thick curtains are used to separate it (pay attention to the reflection of the ceiling and floor), the flashing of lights can be avoided.

As long as the flasher does not use the same wireless signal frequency, wireless serial flicker can be avoided.

If your flasher can adjust the frequency of signal transmission and reception (a pair of 2-position microswitches on the transmitter and receiver), as long as the flashers in two sheds use different working frequencies, that is, the combination of 1 and 2 switches on the transmitter and receiver is different (the combination switches in different sheds are different, and the combination of transmission and reception in the same shed is the same), wireless flicker can be avoided.

If your current flasher doesn't have the function of adjusting channels.

You have to buy another set of flashers.

Note that it must be a different brand. When you buy it, bring your current flash, and don't use the old and the new.

It's best to buy an adjustable channel, and you can change the frequency by adjusting the channel in the future, which is convenient and flexible for grouping.

Finally, I would like to remind you that lighting and wireless lighting must do a good job of preventing crosstalk at the same time, so that the two sheds can not crosstalk.

If only the grouping of wireless flash is solved, but the light leakage between the two sheds is serious, it will still cause flash.

If you have any questions, please ask.

Question 5: How to set the aperture F8~F 1 1, shutter1125 ~1/250s and ISO to the lowest?

The low-grade flasher only has flashing function, while the high-grade flasher can directly control the output power of the lamp, and it can be adjusted by pressing+-.

Question 6: How to set the flasher and external flash? Playing with lights in a 5-point big scene is nothing more than manual operation, and m-block jumping is king ~ ~ ~

Question 7: The problem of flasher. I was a photographer a few years ago. There are usually four flashers about this.

The channel of the flasher plugged into your camera should be the same as the channel on the flash, so that it can flash. For example, if the flash is set to a, the flash above the flash should also be set to a.

The reason why the flash has several channels is that some large wedding photo studios have several photographers, so even if they take pictures at the same time, there will be no conflict as long as the channels are different. It can be seen that there is no problem for the flasher to flash six or seven times.

He is a sign that power is open. It doesn't matter. I hope to adopt.

Question 8: How to connect the flash of Canon 6D camera? I don't know how to set the flash. Please tell me that two flashers have the same frequency, so that they can work at the same time. Then set the flash mode, which is synchronous flash.

Question 9: First of all, it's best to choose "old" brands that have been listed earlier, because they entered the field earlier and their technology is more mature, so it's not necessary to choose products from well-known manufacturers, because most of these well-known manufacturers don't produce their own products, but only order other people's products for OEM. Secondly, we should know the level of repair rate and the supplier's three guarantees. When reading the product manual, don't be confused by the manufacturer's patent, serial number, single chip microcomputer,1/2000s, 4th gear and16th gear. After seeing a brand, the only thing that can prove the quality is the actual test. Connect the receiver to the flashlight and the transmitter to the camera. Set the camera shutter to11000 seconds or 1/500 seconds. If the place permits, it can be more than 30 meters apart. Put the camera in various directions and postures, and shoot it repeatedly to see if there are any blind spots and whether it hits the target. Through the above tests, the reliability of the flasher can be explained. If your actual use environment is seriously disturbed, you should also choose products with good anti-interference performance, such as places where power tools are often used near the photo studio, and users had better borrow a pistol when buying. If there is no other photo studio within 30 meters of your photo studio, or there is only one studio in the photo studio, there is no need to choose multiple products. In addition to the frequency of 7KHZ, the performance of multi-file products will decrease the response speed to the next file, that is, the shutter speed of the camera will decrease accordingly. Do not choose products with 6V and 9V batteries. Both of these batteries have short service lives. It's best to choose the product of battery No.5, and battery No.7 will do. There are two types of wireless flashers: RF flashers and infrared flashers. Most flashers use this radio frequency signal. The RF flasher is not affected by sunlight, and the transmitter and receiver can flash even when they are not in sight, and the flashing distance is relatively far (Yuan Boxin micro scheme). Radio frequency flashers include: Puwei Plus II, Multimax, TT 1, TT 5 pixel F-5 10 TR-332 Yongnuo 602, PT-04Radio Popperking pro king Third Generation Wireless TTL high-speed synchronous color Amazon flagship store lead RF-604 Wireless transceiving flasher lead Amazon flagship store lead VF-90 1 Plug-in umbrella flasher and other infrared flashers are divided into two different devices (there are also two in 1). The transmitter must be in the line of sight before it can be used (that is, the receiver can see the transmitter directly, otherwise it can't flash. In addition, there must be no obstacles between the transmitter and the receiver). Infrared flasher is greatly influenced by sunlight, in this case, the use range of flasher will be shortened. The premise of using this flasher is that the flasher must have its own infrared device. Many models of flashlights, including Canon and Nikon, are equipped with infrared devices (Yuan Bo Core Micro Scheme). The devices with infrared devices are: Canon Flash (Yuan Boxin Micro Scheme): 580EX (transmitting and receiving), 580EX II (transmitting and receiving), 430EX (receiving), 430EX II (receiving) and so on. Nikon flash: SB900 (transceiver), SB800 (transceiver), SB600 (receiver), etc. Yongnuo flash: YN465, YN467, YN468, etc. Infrared controller (Yuan Boxin micro scheme): Canon ST-E2, Nikon SU-800, Yongnuo ST-E2, etc. There are not many advantages in using infrared devices to trigger the flash, but if you already have devices that support this technology, infrared may be suitable for you. However, the photographer should consider the needs of the shooting task when choosing which flash mode to use. The most important decision is whether the shooting task needs TTL automatic flash. Flash always suggests shooting in manual mode (camera and flash), but in some cases only TTL flash can be used. So let's look at TTL first. TTL is a photometric system of flash, which is used to represent a flash system that uses "through lens" to measure exposure. TTL is a more accurate system, because all shooting factors, including aperture, focal length, object distance, filter and reflected light, can be considered by lens test, so as to calculate the best flash power. TTL is very suitable for shooting moving objects or other situations where manual flash cannot be set in advance. Many wedding photography, children photography, sports photography, news photography, etc. Will choose to use TT>>.

Question 10: How does the studio flash? 1 You must buy a set of flasher or connecting cable first, and the emitter of the flasher is plugged into the camera;

2. Determine the main lamp, and insert the receiving end of the flasher into the main lamp;

3 turn on all flashlights to be used;

Because there is a red "light sensor" on each studio lamp, as long as the main lamp can shoot or refract to the sensor when flashing, other lamps without flash receiver will automatically flash;

Now some indoor shooting also uses multiple flashers instead of sensitivity, because if there are fewer refractors and the angle is wrong, the success rate of flashing will be reduced. The receiver installed on each lamp is different. You don't need to test the light sensor, just accept the camera stalk directly;

6 When there are many outdoor lights, it is best not to flash by lights, which will make you angry in many cases.