It's been raining. What's with the water drops on the wall?

It's been raining, and the wall tiles are full of water.

It has been raining, and the tiles on the wall are full of water. Decorating the house is a major event in our life. Floor tiles can be said to be a very common building material, but often in some low-rise households, when it rains, floor tiles will pop out of the ground. The following sharing has been raining. The tiles on the wall are all water.

It has been raining, and the tiles on the wall are full of water. 1 1. What's the matter with water droplets on the wall in rainy days?

1. What's with the water droplets on the wall in rainy days? There are many reasons. Indoor walls are damp, unventilated, and poor waterproof, which will be more serious in rainy days. If you want to check the project of the house, you can check it in rainy days to see if there is some color difference on the wall, which is large or darker than other walls. If there is moisture on the wall, you can touch it with your hand to see if there are some abnormal phenomena on other walls, then you can judge that there is water seepage.

2. If there are cracks in the wall, it means that the surface on the wall is obviously leaking and moldy, which is mostly caused by water leakage.

3. In addition, the temperature of ceiling and wall is lower than that of indoor air, so moisture will condense on the deposited wall and eventually produce water droplets. In fact, water droplets on the ceiling or walls are more common. Under normal circumstances, higher temperature can hold more water vapor. When the temperature drops suddenly, the moisture content in the air will increase. Far beyond the limit of water vapor that can be contained at this time, excess water vapor in the air will condense into water droplets.

Second, what's the matter with water drops on the wall in rainy days-wall protection skills

1. In general, the friction on the wall is relatively small, and the change of the wall is mainly caused by water drops or dust. So at this time, you can use a rag to remove the dust on the surface or use wax water spray for maintenance. Because spraying water not only plays a cleaning role, but also forms a transparent protective film, which is very convenient.

2. For the maintenance of the bathroom wall, it is recommended to use alkaline cleaning agent for maintenance, but after cleaning, it should be washed with clear water, otherwise the surface will lose its original brightness.

It has been raining, and the tiles on the wall are full of water. What are the tricks to deal with the water on the tiles in rainy days?

1, which is a common resurgence situation. You can drag it on the ground with a dry mop for a few times to relieve the damp phenomenon.

Spread a carpet on the floor to let the water absorb, and then take it away to dry when the weather is dry.

3, usually must pay attention to open the window ventilation, close the doors and windows when it rains, to prevent outdoor moisture from entering.

What are the reasons for the resurgence of tiles?

1, related to the season, especially in our south, when it rains, tiles are particularly prone to moisture regain. Rainy weather, the temperature is relatively high, so the humidity is relatively high, which is easy to produce water droplets, but this phenomenon will disappear when the weather improves.

2. Regarding the ground treatment, the waterproof treatment of the foundation was not done well when the tiles were laid, or the purchased tiles did not absorb water, resulting in the formation of water vapor in the underground soil. The tiles are wet, which leads to high humidity in the room. This situation is troublesome to deal with, and it is necessary to deal with the waterproof problem of foundation again.

3. The ventilation effect is not good, and there is water leakage in the room, which leads to the resurgence of tiles.

How to prevent tiles from foaming

1. When choosing tiles, you must choose tiles with high water absorption. You can pour water on the back of the tile. If the water expands quickly, it means that it does not absorb water, so it is not recommended to buy them.

When the weather is good, you must ventilate more to make the air at home drier.

3, you can put some desiccant or activated carbon in the corner of your home, so that you can absorb indoor moisture.

It has been raining, and the tiles on the wall are full of water. 3. When it rains, there is water on the tiles for the following reasons:

1. It shows that the waterproof layer under the floor tile is unqualified, because it is on the first floor or the bottom floor, and the whole moistureproof and waterproof treatment must be done under the foundation. So if it is rainy, it must be that the waterproof layer below is not done well.

2. The floor tiles always get wet on cloudy days. The reason why the floor tiles get damp is that when the humid air with higher temperature meets the floor tiles with lower temperature, it will easily condense into water on the ground. These floor tiles are smooth and do not absorb water.

Solutions to leakage of floor tiles in rainy days;

1, tear down the floor tiles, and do the whole moistureproof and waterproof treatment again.

2, or try to carefully remove the floor tiles and see if you can keep the removed floor tiles for secondary use, thus reducing some costs.

Classification of floor tiles

The varieties of floor tiles are brick, glazed tile, polished brick, infiltrated brick, infiltrated polished brick and so on. These floor tiles are not all non-slip, especially those with old people and children at home. Be sure to do anti-skid test when buying to avoid problems. Common floor tiles are glazed tiles, vitrified tiles, polished tiles, inferior smooth brick, glazed tiles, printed tiles, non-slip tiles and special acid-resistant floor tiles.

Floor tile laying method

There are two ways of paving floor tiles, one is dry paving and the other is wet paving. The difference between the two is that:

1, dry paving is actually the method of paving marble. 1: 3 cement mortar was kneaded into a ball by hand and blossomed on the ground. Dry bricklaying is not easy to be hollowed out, saving time and construction period. However, the mortar thickness of dry-fired bricks is relatively large (3~4cm), so dry-fired bricks can be used if large-sized bricks are used in the living room.

2. Wet paving is to spread cement directly behind the brick, and then spread it directly on the wall or the ground. Wet paving is used to lay tiles on the wall. If the flatness of small bricks and the ground is good, it is best to use wet paving, which can save the thickness of the ground.

3. The quality of the two paving methods is the same, and the choice of which method depends on the specific situation (generally, the bricklayer's paving decision is correct. ) Generally, the kitchen and bathroom are wet-paved, and the living room can be dry-paved. Dry floor mortar needs a certain thickness (at least 3~4cm), and the kitchen floor is definitely not thick enough to be wet.

It has been raining, and the tiles on the wall are full of water. 4. What should I do if the tile floor at home suddenly absorbs a lot of water?

1. Because of dew condensation, there is a temperature difference in ceramic tile insulation, and indoor humidity produces dew condensation. Wipe it with a dry cloth and dehumidify it with a dehumidifier. After dehumidifying the room, the problem of water leakage can be solved.

2. Because the air humidity is high and the atmosphere is low, when the temperature difference between indoor and outdoor is large, the cold and warm air inside and outside interacts, and water mist will be formed on the surface when the doors and windows are opened. At this time, it is necessary to reduce the time to open the doors and windows, and then wipe them clean with a mop.

Second, what should I do if the water pipe at home bursts?

1. Let's see if the power is off first. Because water is conductive, it is easy to be dangerous, so turn off the power first. Then start to check how much water leaked after the water pipe burst, which is generally directly related to the water pressure in the pipe. Whether it is dripping or spewing out, the most important thing at this time is to immediately close the valve of the water supply pipe and report it to the local property department for repair.

2. Wrap the damaged part of the water pipe with special tape for repairing the water pipe. In addition, glass fiber tape or epoxy resin glue can also be used to repair cracks in water pipes.

If the water pipe bursts seriously, you can wrap the broken part of the water pipe with a towel. This can not only prevent water from spraying everywhere, but also introduce water into the placed bucket to avoid huge waste. At the same time, the valve of the main water pipe in the house can be closed, and the tap water supply in the house can be completely cut off.

5. If the cause of the water pipe burst is that the water pipe is too old, you should find a plumber to check and repair it in time.