The maple board is too smooth. How to paint, what color to use, and what paint to use are easier to ensure that the color will not turn yellow.

If you want to use white maple board, I suggest you keep the color of the log and paint it with varnish, because no matter whether you add toner or color, the average worker will brush it unevenly! If you really want to change the color, then I suggest you use toner that matches the paint and find a good worker. The board can't be primed for the first time before entering the site! I'll tell you more about painting construction technology, hoping to help you! Paint is said to be "three-point carpenter's seven-point paint" in decoration. The position of painting technology in decoration is very critical.

The commonly used painting processes are listed as follows for reference.

First, wood lacquer

First, the glazing process

1) is coated with colored oil or colored oil (note: it is only used for projects with discoloration requirements, and this process is not required for ordinary projects. )

2) Brush varnish to protect primer (if there is no 1 procedure, this procedure is the first procedure).

If the paint is a primary color paint, the surface must be cleaned after purchasing materials at the construction site, and the first protective primer should be applied immediately. Primer usually consists of topcoat.

* varnish surface painting must be carried out before wall painting.

3) Clean the dust and dirt on the wood surface.

4) Use sandpaper to polish the board surface or wood line surface.

5) Brush the paint for the first time.

6) After thoroughly drying, use prepared toner, cooked rubber powder and Shuangfei powder as putty to cover nail holes and tree scars to make them consistent with their true colors.

7) After thorough drying, polish the rough part of the toner with fine sandpaper. At this time, polishing the surface is very important.

8) Brush the paint once.

9) Dry and polish with fine sandpaper.

10) Brush the paint once.

(that is, after painting, add fine sandpaper to polish it, and so on. If there is a special primer, replace the first coat with a special primer)

1 1) First wet the wood surface with a wet cloth, and then wet the surface with sandpaper, commonly known as water mill.

12) brush for the last time.

Generally speaking, counting the last layer, * * * needs to be painted for about 4 to 8 times to get better results. The more times of surface painting, the better, but generally not more than 10 times.

During construction in wet weather, the paint film will turn white, which can be eliminated by adding nitro magnetized white water with dilution of 10 ~ 15%.

B, oil mixing process

1) Clean up the dust and dirt on the wood surface first.

2) Mix the surface of the whole batch of wood with pig blood ash and Shuangfei powder.

3) Dry thoroughly and polish with sandpaper.

4) Brush the paint for the first time

5) make up for the defects.

6) Dry thoroughly and polish with sandpaper.

7) Brush the paint for the second time

8) Dry thoroughly and polish with sandpaper.

9) Brush the paint for the third time.

Generally speaking, it is advisable to mix oil two or three times.

Precautions:

1. Paint construction must be carried out within the indoor temperature required by the product. Different products have different temperature requirements, which can be found in the product packaging or instructions.

2, each working procedure to ensure the second dry edge.

3. Use the same coating, and don't mix different kinds of coatings to avoid adverse reactions.

4, construction, to do a good job in safety measures, such as masks.

5, keep indoor ventilation, in case of poisoning.

6. When using corrosive paint, such as Tinea water, please wear rubber gloves.

7. Don't smoke or use naked flame in the construction site to prevent fire or explosion.

8. Avoid forced construction in the case of high humidity or cold.

9. If there is a gap in the ceiling or wooden partition that needs to be concealed, it can be treated with putty and then pasted with high-quality anti-crack tape; Wall cracks can be scraped flat, filled with gypsum, and then pasted with high-quality anti-crack tape. Then brush the surface.

10, insist on buying paint in regular shops, and the quality will be guaranteed.